How Should You Safely Service the Fuel Filler Hose on an All Wheel Drive (AWD) on Ford Fusion?

Operation of the all wheel drive (AWD) vehicle fuel tank filler pipe demands that users remain away from fuel-related components which contain highly flammable mixtures because it is dangerous to smoke or use open flames or personal electronic devices while working in this area. It is necessary to ease fuel system pressure before unconnecting fuel system components because this action prevents accidental fuel spraying. The first step involves hoisting the vehicle in neutral position to next remove the muffler together with the tailpipe. Through proper care disable the battery ground cable and twist the fuel tank filler cap counter-directionally until it unlocks. The agitating motion during fuel draining hose removal should be gentle to maintain its position to the fitting. Connect a fuel storage tanker to the fuel draining hose which should be inserted into the fuel tank filler pipe to enable the safety valve and enable draining about one-eighth of the tank volume while lowering fuel below the inlet. First uninstall the three fuel tank filler pipe retaining screws then remove the LH rear wheel and tire and three rivets and six pin-type retainers and the LH wheel splash shield. The fuel tank filler pipe heat shield can be removed by detaching the fresh air hose fitting from its housing and removing its three nuts prior to reinstallation with a torque of 9 Nm (80 lb-in). The worker should disconnect the fuel vapor assembly from the recirculation tube followed by unfastening the fresh air hose from the dust separator and removing the fuel tank filler nut. Reinstallation of this part requires a torque of 10 Nm (89 lb-in). You should disconnect the swivel clips before removing four screws to free the fuel tank filler pipe housing while loosening the LH fuel tank strap bolts to 40 Nm (30 lb-ft) for reinstallation. Lower down the LH portion of the fuel tank enough for accessing the fuel tank filler hose and clamp and drain remaining fuel into an appropriate container. The technician either releases the clamp during the procedure and disconnects the filler hose from the fuel tank at a torque value of 4 Nm (35 lb-in) before tightening it for reinstallation. Before removing the fuel tank filler pipe assembly from the vehicle motorists need to position it upward into the fuel door opening while also extending it partially through the aperture. The installation process should be finished by reverting back to all removal steps.

OEM Ford Fusion Fuel Filler Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Fuel Filler Hoses found

View related parts
Ford Fusion Pipe Assembly Part Number: AE5Z-9034-AF
$182.06 MSRP: $265.00
You Save: $82.94 (32%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Filler Pipe
- Replaces: AE5Z-9034-R, AE5Z-9034-AC, AE5Z-9034-U, AE5Z-9034-Y
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | S, SE, SEL, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Filler Neck Part Number: AE5Z-9034-AH
$141.06 MSRP: $205.33
You Save: $64.27 (32%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Pipe Assembly; Filler Pipe
- Replaces: AE5Z-9034-AA, AE5Z-9034-X, AE5Z-9034-AE, AE5Z-9034-T
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Fusion Filler Tube Part Number: 8U5Z-17B068-B
$6.11 MSRP: $8.67
You Save: $2.56 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Funnel; Fuel Filler Neck Adapter; Fuel Filler Neck Sleeve; Filler Neck Sleeve; Fuel Filler Hose; Fuel Tank Filler; Filler Pipe Tube; Tube; Filler
- Manufacturer Note: Attached To Underneath 42624 In Luggage Compartment
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Hybrid, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, SEL, SEL Hybrid, Sport, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Connector Hose Part Number: DG9Z-9047-C
$74.44 MSRP: $108.35
You Save: $33.91 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose - Filler Pipe; Fuel Filler Hose; Fuel Filler Neck; Filler Hose
- Replaces: DG9Z-9047-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, SEL, SEL Hybrid, Sport, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Pipe Assembly Part Number: AE5Z-9034-AG
$142.32 MSRP: $207.17
You Save: $64.85 (32%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Filler Pipe
- Replaces: AE5Z-9034-Z, AE5Z-9034-AD, AE5Z-9034-V, AE5Z-9034-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | S, SE, SEL, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Connector Hose Part Number: DG9Z-9047-B
$270.13 MSRP: $396.67
You Save: $126.54 (32%)
ADD TO CART
Product Specifications
- Other Name: Hose - Filler Pipe; Fuel Filler Hose; Fuel Filler Neck; Filler Hose
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | Energi SE, Energi Titanium | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Fusion Filler Hose Part Number: 7E5Z-9047-A
$36.23 MSRP: $51.83
You Save: $15.60 (31%)
Product Specifications
- Other Name: Hose - Filler Pipe; Fuel Filler Hose; Lower Hose
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2012 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Filler Hose Part Number: 7E5Z-9047-B
Product Specifications
- Other Name: Hose - Filler Pipe; Fuel Filler Hose; Filler Neck Hose; Lower Hose
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2012 Ford Fusion | S, SE, SEL, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Lower Hose Part Number: 6E5Z-9047-AA
Product Specifications
- Other Name: Hose - Filler Pipe; Fuel Filler Hose
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

Ford Fusion Fuel Filler Hose

OEM Fuel Filler Hose boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Fuel Filler Hose with long life and a perfect fit. Come to our website and find genuine Ford Fusion parts. We keep a wide inventory of OEM Fusion parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Ford Fusion Fuel Filler Hose in the Ford Fusion automobiles is an essential part considering the fact that it plays the role of a fuel filler hose that delivers fuel safely and efficiently to the fuel tank of the automobile. This Fuel Filler Hose is capable of fixing firmly to the fuel fill cap inlet with the help of strong clamps and screws that firmly fix the fuel system making it more accurate and dependable. Its compatibility with different ford fusion model, produced since 2005, stresses its importance for preserving the car fuel system's integrity. The Ford Fusion Fuel Filler Hose is not only an aid in providing required fuel to the car but also contributes to a better performance of a car and probably efficiency too. The ever reliable Fuel Filler Hose in the automotive market is appreciated for its durability and efficiency by offering the Ford's owners appropriate security from fuel threats and system vulnerability. Ford Fusion has been realized to have strong env ironmental features and the Fuel Filler Hose supports th is by delivering fuel without leakage or wastage. Furthermore, the Design of the Fuel Filler Hose corresponds to Ford quality and innovation hence, it is part of Fusion's engineering. Thus, the Ford Fusion Fuel Filler Hose can be viewed as embodying the essential features of the brand as a performance- and safety-oriented element in the Ford Fusion fuel system.

Ford Fusion Fuel Filler Hose Parts and Q&A

Filler Hose
7E5Z-9047-A
Q: How Should You Safely Service the Fuel Filler Hose on an All Wheel Drive (AWD) on Ford Fusion?
A:
Operation of the all wheel drive (AWD) vehicle fuel tank filler pipe demands that users remain away from fuel-related components which contain highly flammable mixtures because it is dangerous to smoke or use open flames or personal electronic devices while working in this area. It is necessary to ease fuel system pressure before unconnecting fuel system components because this action prevents accidental fuel spraying. The first step involves hoisting the vehicle in neutral position to next remove the Muffler together with the tailpipe. Through proper care disable the battery ground cable and twist the fuel tank filler cap counter-directionally until it unlocks. The agitating motion during fuel draining hose removal should be gentle to maintain its position to the fitting. Connect a fuel storage tanker to the fuel draining hose which should be inserted into the fuel tank filler pipe to enable the safety valve and enable draining about one-eighth of the tank volume while lowering fuel below the inlet. First uninstall the three fuel tank filler pipe retaining screws then remove the LH rear wheel and tire and three rivets and six pin-type retainers and the LH wheel splash shield. The fuel tank filler pipe heat shield can be removed by detaching the fresh air hose fitting from its housing and removing its three nuts prior to reinstallation with a torque of 9 Nm (80 lb-in). The worker should disconnect the fuel vapor assembly from the recirculation tube followed by unfastening the fresh air hose from the dust separator and removing the fuel tank filler nut. Reinstallation of this part requires a torque of 10 Nm (89 lb-in). You should disconnect the swivel clips before removing four screws to free the fuel tank filler pipe housing while loosening the LH fuel tank strap bolts to 40 Nm (30 lb-ft) for reinstallation. Lower down the LH portion of the fuel tank enough for accessing the fuel tank filler hose and clamp and drain remaining fuel into an appropriate container. The technician either releases the clamp during the procedure and disconnects the filler hose from the fuel tank at a torque value of 4 Nm (35 lb-in) before tightening it for reinstallation. Before removing the fuel tank filler pipe assembly from the vehicle motorists need to position it upward into the fuel door opening while also extending it partially through the aperture. The installation process should be finished by reverting back to all removal steps.