How to Safely Service and Repair a Fuel Pump Module on Ford Fusion?

The high flammability of mixtures inside the fuel gauge sender and fuel pump module demands necessary safety guidelines before maintenance operations. The first step should include lowering fuel system pressure followed by disconnecting the battery ground cable. You should turn the fuel tank filler cap counterclockwise about one-fourth turn before placing it safely to the side. The procedure for removing the Fuel Draining Hose involves slight shaking movements to prevent the fitting from breaking loose while the hose should be inserted into the fuel tank filler pipe until the fitting activates the safety valve. The Fuel Storage Tanker should be connected to the Fuel Draining Hose for drawing out one-eighth of the fuel tank volume until the fuel sits below the fuel pump module mounting flange. Begin by removing the rear seat lower cushion and then proceed to take four screws off the fuel pump module access cover for front-wheel drive vehicles but use three screws for all-wheel drive vehicles. The user should disconnect both the fuel pump module electrical connection and the quick connect coupling between the fuel tube and the fuel pump module. The technician should place absorbent pads on the floor pan before carefully removing the fuel pump module from the vehicle while installing a new fuel pump module O-ring seal and lock ring. The Fuel Tank Sender Unit Wrench should be used to eliminate and dispose of the fuel pump module lock ring. All-wheel drive vehicles require the fuel pump module to be lifted from the fuel tank for exposing the quick connect coupling between the fuel tube and fuel pump module. Take care with the fuel pump module handling to protect the float arm while you fill fuel residue into appropriate storage. A replacement of either the fuel pump module or fuel tank is necessary if any evidence of bending, scratching or corrosion is present on their contact surface areas during mating surface inspection. Clean engine oil must be applied to the new O-ring seal for installation then the repair procedure should be done in reverse order while checking for proper alignment of the fuel pump module alignment tab with the fuel tank before tightening the lock ring.

OEM Ford Fusion Fuel Pump

Gas Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

29 Fuel Pumps found

View related parts
Ford Fusion Fuel Pump Part Number: HG9Z-9H307-K
$776.25 MSRP: $1254.55
You Save: $478.30 (39%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Assembly
- Replaces: HG9Z-9H307-H, HG9Z-9H307-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: EJ7Z-9350-A
$239.64 MSRP: $351.90
You Save: $112.26 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly - Fuel; Direct Injection High Pressure Fuel Pump; Gasoline Direct Injector Pump
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: EG9Z-9H307-A
$279.27 MSRP: $474.55
You Save: $195.28 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Electric Fuel Pump; Fuel Pump Module Assembly; Fuel Pump Assembly
- Manufacturer Note: Before Ordering Please Refer To OASIS Message SSM 46126 Or BCM 3847
- Replaces: DG9Z-9H307-S, DG9Z-9H307-D, PFS-958, PFS-1000
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | S, S Hybrid, SE, SE Hybrid, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: DG9Z-9H307-Y
$228.86 MSRP: $380.00
You Save: $151.14 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Electric Fuel Pump; Fuel Pump Module Assembly; Fuel Pump Assembly
- Replaces: PFS-996, DG9Z-9H307-A, PFS-955, DG9Z-9H307-N
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: DG9Z-9H307-AA
$394.20 MSRP: $654.55
You Save: $260.35 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Electric Fuel Pump; Fuel Pump Module Assembly
- Manufacturer Note: Before Ordering Please Refer To SSM 46126
- Replaces: DG9Z-9H307-U, PFS-1002, DG9Z-9H307-G, PFS-967
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013 Ford Fusion | S, SE, Titanium | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Fuel Pump, Driver Side Part Number: DG9Z-9H307-T
$336.17 MSRP: $558.18
You Save: $222.01 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module Assembly; Fuel Pump Assembly
- Position: Driver Side
- Replaces: DG9Z-9H307-F, PFS-966
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | S, SE, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Fuel Pump, Driver Side Part Number: AE5Z-9H307-J
$230.41 MSRP: $369.09
You Save: $138.68 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Manufacturer Note: Service Kit
- Position: Driver Side
- Replaces: AE5Z-9H307-C, PFS-540
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Fuel Pump, Passenger Side Part Number: DG9Z-9275-A
$101.22 MSRP: $160.73
You Save: $59.51 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Electric Fuel Pump, Right; Fuel Transfer Unit; Fuel Pump Assembly
- Manufacturer Note: Before Ordering Please Refer To OASIS Message SSM 46126 Or BCM 3847
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | S, SE, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: 7E5Z-9H307-T
$241.00 MSRP: $363.64
You Save: $122.64 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: FT4Z-9350-B
$299.64 MSRP: $440.00
You Save: $140.36 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly - Fuel; Direct Injection High Pressure Fuel Pump
- Replaces: FT4Z-9350-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: DS7Z-9350-C
$273.92 MSRP: $426.67
You Save: $152.75 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly - Fuel; Direct Injection High Pressure Fuel Pump; Gasoline Direct Injector Pump
- Replaces: DS7Z-9350-A, DS7Z-9350-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit, Passenger Side Part Number: 7E5Z-9275-C
$66.79 MSRP: $92.40
You Save: $25.61 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger; Sending Unit; Fuel Level Sensor; Fuel Pump.; Fuel Pump Assembly; Fuel Sender Unit
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2012 Ford Fusion | SE, SEL, Sport | 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: AE5Z-9H307-L
$329.60 MSRP: $547.27
You Save: $217.67 (40%)
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump and Sender Assembly; Fuel Pump Module Assembly; Electric Fuel Pump; Fuel Pump Assembly
- Manufacturer Note: Service Kit
- Replaces: AE5Z-9H307-E, PFS-542
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | SE, SEL | 6 Cyl 3.0 L FLEX
View related parts
Ford Fusion Fuel Pump, Driver Side Part Number: DG9Z-9H307-R
$272.85 MSRP: $463.64
You Save: $190.79 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Electric Fuel Pump, Left; Fuel Pump Module Assembly; Fuel Pump Assembly; Electric Fuel Pump
- Manufacturer Note: Before Ordering Please Refer To OASIS Message SSM 46126 Or BCM 3847
- Position: Driver Side
- Replaces: DG9Z-9H307-B, PFS-956
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | S, SE, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: 8E5Z-9H307-T
$221.49 MSRP: $376.36
You Save: $154.87 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump and Sender Assembly; Fuel Pump Module Assembly; Strainers & Misc Prt; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: 6E5Z-9H307-G
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: 7E5Z-9H307-S
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Replaces: 6E5Z-9H307-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: 7E5Z-9H307-U
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: 8E5Z-9H307-S
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: AE5Z-9H307-G
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Manufacturer Note: Service Kit
- Replaces: PFS-539, AE5Z-9H307-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Sport | 6 Cyl 3.5 L GAS

| Page 1 of 2 |Next >

1-20 of 29 Results

Ford Fusion Fuel Pump

OEM Fuel Pump boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Fuel Pump with long life and a perfect fit. Come to our website and find genuine Ford Fusion parts. We keep a wide inventory of OEM Fusion parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Fuel Pump in Ford Fusion cars is responsible for the supply of fuel from the tank to the engine's fuel injection part. First of all, it is necessary to underline that in Ford Fusion models, there is often an electric fuel pump used, which is mounted inside a fuel tank, and may be connected to a sending unit that displays fuel quantity in the tank. These pumps are intended to deliver higher pressures made an imperative requirement in the current day fuel injection control to promote better combustion and performance of the engine. On the other hand, older Ford Fusion cars models may have used mechanical fuel pumps often located outside the vehicle and function using lower pressures that are appropriate for carburetor equipped engines. Mechanical pumps are no longer used in most systems due to poor efficiency but they are used in situations whereby low pressures suffice. The change of fuel pumps working mechanically to electric pumps in the Ford Fusion automobiles demonstrates new inventions to better control fuels as well as aspects of safety.

Ford Fusion Fuel Pump Parts and Q&A

Fuel Pump
8E5Z-9H307-T
Q: How to Safely Service and Repair a Fuel Pump Module on Ford Fusion?
A:
The high flammability of mixtures inside the fuel gauge sender and fuel pump module demands necessary safety guidelines before maintenance operations. The first step should include lowering fuel system pressure followed by disconnecting the battery ground cable. You should turn the fuel tank filler cap counterclockwise about one-fourth turn before placing it safely to the side. The procedure for removing the Fuel Draining Hose involves slight shaking movements to prevent the fitting from breaking loose while the hose should be inserted into the fuel tank filler pipe until the fitting activates the safety valve. The Fuel Storage Tanker should be connected to the Fuel Draining Hose for drawing out one-eighth of the fuel tank volume until the fuel sits below the fuel pump module mounting flange. Begin by removing the rear seat lower cushion and then proceed to take four screws off the fuel pump module access cover for front-wheel drive vehicles but use three screws for all-wheel drive vehicles. The user should disconnect both the fuel pump module electrical connection and the quick connect coupling between the fuel tube and the fuel pump module. The technician should place absorbent pads on the floor pan before carefully removing the fuel pump module from the vehicle while installing a new fuel pump module O-ring seal and lock ring. The Fuel Tank Sender Unit Wrench should be used to eliminate and dispose of the fuel pump module lock ring. All-wheel drive vehicles require the fuel pump module to be lifted from the fuel tank for exposing the quick connect coupling between the fuel tube and fuel pump module. Take care with the fuel pump module handling to protect the float arm while you fill fuel residue into appropriate storage. A replacement of either the fuel pump module or fuel tank is necessary if any evidence of bending, scratching or corrosion is present on their contact surface areas during mating surface inspection. Clean engine oil must be applied to the new O-ring seal for installation then the repair procedure should be done in reverse order while checking for proper alignment of the fuel pump module alignment tab with the fuel tank before tightening the lock ring.