How to service the fuel level sensor safely and effectively on Ford Fusion?

Service of the fuel level sensor must begin with safety precautions such as preventing smoking and using open flames and personal electronic devices close to fuel components because these areas contain flammable mixtures. You must first drain fuel system pressure while disconnecting the ground cable from the battery. Rotate the fuel tank filler cap in the counterclockwise direction only a quarter turn then place it safely aside. The Fuel Draining Hose removal must involve slow hose movement to stop fitting detachment while proper funnel placement inside the fuel tank filler pipe until the fitting activates safety valve operation. The Fuel Storage Tanker needs attachment to the Fuel Draining Hose for fuel removal until the sensor mounting flange reaches a position below the fuel level. Afterward, the fuel level sensor access cover can be accessed by removing three screws which must be torqued to 2 Nm (18 lb-in) following reinstallation. The sensor requires you to disconnect its electrical connector then put absorbent pads under work area and release the lock tab to rotate counterclockwise until you lift it out. Carefully handle the fuel level sensor to prevent damage to its float arm while inspecting the sensor flange and O-ring contact areas of the mating surfaces; bendage or corrosion or scratches require replacement of the sensor or fuel tank. Always replace the O-ring seal and apply clean engine oil to it before the installation process. Reverse all removal steps by placing the locking tab of the fuel level sensor in its correct position.

OEM Ford Fusion Fuel Level Sensor

Gas Gauge Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 Fuel Level Sensors found

View related parts
Ford Fusion Fuel Pump Part Number: HG9Z-9H307-K
$776.25 MSRP: $1254.55
You Save: $478.30 (39%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Assembly
- Replaces: HG9Z-9H307-H, HG9Z-9H307-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: FP5Z-9A299-B
$117.94 MSRP: $187.27
You Save: $69.33 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit; Fuel Level Sensor; Fuel Sending Unit; Sending Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: AE5Z-9A299-G
$36.39 MSRP: $50.34
You Save: $13.95 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Sending Unit
- Manufacturer Note: Service Kit
- Replaces: AE5Z-9A299-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | SE, SEL | 6 Cyl 3.0 L FLEX
View related parts
Ford Fusion Fuel Gauge Sending Unit, Driver Side Part Number: AE5Z-9A299-F
$69.47 MSRP: $96.10
You Save: $26.63 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Pump Module; Fuel Level Sensor; Sending Unit; Fuel Sender Unit; Sending Unit
- Manufacturer Note: Service Kit
- Position: Driver Side
- Replaces: AE5Z-9A299-B, PS-392
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: 7E5Z-9A299-T
$56.80 MSRP: $78.58
You Save: $21.78 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Sending Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: DG9Z-9A299-M
$159.84 MSRP: $269.09
You Save: $109.25 (41%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit; Fuel Level Sensor; Fuel Sending Unit; Sending Unit
- Replaces: DG9Z-9A299-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, SEL, SEL Hybrid, Sport, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: HG9Z-9A299-G
$102.56 MSRP: $172.18
You Save: $69.62 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Level Sensor; Fuel Sending Unit; Sending Unit
- Replaces: HG9Z-9A299-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: EG9Z-9A299-A
$98.88 MSRP: $166.00
You Save: $67.12 (41%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Sending Unit; Fuel Pump Module; Level Sensor.; Sending Unit
- Replaces: DG9Z-9A299-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | S, S Hybrid, SE, SE Hybrid, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: EG9Z-9H307-D
$364.61 MSRP: $623.64
You Save: $259.03 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Electric Fuel Pump; Fuel Pump Module Assembly; Fuel Pump Assembly
- Replaces: PFS-1077, DG9Z-9H307-M, EG9Z-9H307-B, PFS-982
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, SEL, SEL Hybrid, Sport, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit, Driver Side Part Number: DG9Z-9A299-C
$64.46 MSRP: $102.36
You Save: $37.90 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Left Fuel Tank Sending Unit; Fuel Pump Module; Fuel Level Sensor.; Sending Unit
- Manufacturer Note: Use With 9H307 Fuel Pump
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: DG9Z-9A299-H
$96.93 MSRP: $162.73
You Save: $65.80 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit; Fuel Level Sensor; Fuel Sending Unit; Sending Unit
- Replaces: DG9Z-9A299-D, PS-945
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Pump, Passenger Side Part Number: DG9Z-9275-A
$101.22 MSRP: $160.73
You Save: $59.51 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Electric Fuel Pump, Right; Fuel Transfer Unit; Fuel Pump Assembly
- Manufacturer Note: Before Ordering Please Refer To OASIS Message SSM 46126 Or BCM 3847
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | S, SE, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit, Passenger Side Part Number: DG9Z-9A299-E
$61.72 MSRP: $98.00
You Save: $36.28 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit, Right; Fuel Transfer Unit; Fuel Level Sensor; Fuel Sending Unit; Sending Unit
- Manufacturer Note: Use With 9275 Fuel Pump
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | S, SE, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: DG9Z-9A299-G
$111.61 MSRP: $183.64
You Save: $72.03 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Sending Unit; Fuel Pump Module; Level Sensor.; Sending Unit
- Replaces: PS-942, DG9Z-9A299-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: HG9Z-9A299-A
$119.08 MSRP: $189.09
You Save: $70.01 (38%)
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit; Fuel Level Sensor; Fuel Sending Unit; Sending Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Pump Part Number: FT4Z-9350-B
$299.64 MSRP: $440.00
You Save: $140.36 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly - Fuel; Direct Injection High Pressure Fuel Pump
- Replaces: FT4Z-9350-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit, Passenger Side Part Number: 7E5Z-9275-C
$66.79 MSRP: $92.40
You Save: $25.61 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger; Sending Unit; Fuel Level Sensor; Fuel Pump.; Fuel Pump Assembly; Fuel Sender Unit
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2012 Ford Fusion | SE, SEL, Sport | 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: AE5Z-9A299-H
$36.39 MSRP: $50.34
You Save: $13.95 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Sending Unit
- Manufacturer Note: Service Kit
- Replaces: AE5Z-9A299-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | SE, SEL | 6 Cyl 3.0 L FLEX
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: 7E5Z-9A299-S
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Fuel Sender Unit; Sending Unit
- Replaces: 6E5Z-9275-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Fuel Gauge Sending Unit Part Number: 8E5Z-9A299-S
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Fuel Sender Unit; Sending Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

| Page 1 of 2 |Next >

1-20 of 22 Results

Ford Fusion Fuel Level Sensor

OEM Fuel Level Sensor boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Fuel Level Sensor with long life and a perfect fit. Come to our website and find genuine Ford Fusion parts. We keep a wide inventory of OEM Fusion parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

When it comes to the function and efficiency of Ford Fusion automobiles, the Ford Fusion Fuel Level Sensor plays a major role. With respect to fuel, this electronic device also monitors the fuel level of the tank and display it to the driver and thus increase efficiency and safety. The Ford Fusion Fuel Level Sensor was intended to work in a high temperature environment; encompassing a float that delegates within an actuating rod and a resistor which in collaboration furnishes the fuel gauge with actual rates. This keeps drivers informed immediately there is a need to refuel to avoid long periods of staking, not to mention mistakes. The Ford Fusion Fuel Level Sensor is useful with different Fusion series; one can effortlessly adjust the Fuel Level sensor across the series, and its functionality will not differ from model to model. The company's reliability is further supported by its fast response-time and energy efficient capabilities that set this particular feature aside in the automotive industry. Furthermore, the Ford Fuel Level Sensor is also a part of the vehicle's eco-friendliness thus supporting the company's key priority of sustainability. Since the Ford Fusion Fuel Level Sensor is made of strong materials and the latest technology, it provides not only luxury to the driver and passengers but also ensures them about the fuel level of their car. In conclusion, the Ford Fuel Level Sensor is an assertation of the company's standards and creativity, which makes it an essential part of the Ford Fusion's engineering prowess.

Ford Fusion Fuel Level Sensor Parts and Q&A

Fuel Gauge Sending Unit
8E5Z-9A299-S
Q: How to service the fuel level sensor safely and effectively on Ford Fusion?
A:
Service of the fuel level sensor must begin with safety precautions such as preventing smoking and using open flames and personal electronic devices close to fuel components because these areas contain flammable mixtures. You must first drain fuel system pressure while disconnecting the ground cable from the battery. Rotate the fuel tank filler cap in the counterclockwise direction only a quarter turn then place it safely aside. The Fuel Draining Hose removal must involve slow hose movement to stop fitting detachment while proper funnel placement inside the fuel tank filler pipe until the fitting activates safety valve operation. The Fuel Storage Tanker needs attachment to the Fuel Draining Hose for fuel removal until the sensor mounting flange reaches a position below the fuel level. Afterward, the fuel level sensor access cover can be accessed by removing three screws which must be torqued to 2 Nm (18 lb-in) following reinstallation. The sensor requires you to disconnect its electrical connector then put absorbent pads under work area and release the lock tab to rotate counterclockwise until you lift it out. Carefully handle the fuel level sensor to prevent damage to its float arm while inspecting the sensor flange and O-ring contact areas of the mating surfaces; bendage or corrosion or scratches require replacement of the sensor or fuel tank. Always replace the O-ring seal and apply clean engine oil to it before the installation process. Reverse all removal steps by placing the locking tab of the fuel level sensor in its correct position.