How to service the 60 percent bench seat armrest on Ford Ranger?

The first step for servicing the 60 percent bench seat armrest requires depowering the supplemental restraint system (SRS) to maintain safety because the safety belt pretensioner operates using pyrotechnics. Safety glasses must be worn by everyone during this operation. Mark the position of safety belt buckle pretensioner wire harness connections as you remove the 60 percent bench seat and write down routing paths which will be needed for reinstallation. First disconnect the safety belt buckle pretensioner electrical connector after removing its anchor clips. Then guide the wire harness through the seat frame. The safety belt buckle pretensioner cover screw needs removal followed by the cover together with the removing of the safety belt buckle pretensioner nut to complete the operation. Unfasten J-clips from the beginning then unfasten the rear armrest J-clip followed by the hook and loop strip while guiding material toward the tether anchor. Users need to first raise the cushion cover with foam pad section and locate the armrest bolts before removing these four bolts to extract the armrest assembly. First disconnect the two armrest bracket bolts before sliding off the respective covers while releasing the bracket cover clips. To install the component begin by reversing the uninstallation procedure starting with the armrest assembly followed by the two armrest bracket bolts then the two armrest bracket covers and finishing with the armrest brackets. Mount the seat cushion foam pad and put on the cover before reattaching the tether anchor material and securing both hook and loop strip and rear armrest J-clip. You should apply the J-clips before putting on the safety belt buckle pretensioner and tightening its nut. After placing back the safety belt buckle pretensioner cover and screw you should connect the safety belt buckle pretensioner wire harness to the seat while securing the clips and electrical connector at its cushion pan. Reinstall the 60 percent bench seat then activate the SRS power while checking for complete functionality without defects until vehicle release.

OEM Ford Ranger Armrest

Car Armrest

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

32 Armrests found

View related parts
Ford Ranger Armrest, Front Driver Side
Part Number: 4L5Z-1024101-AAA
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Left; Arm Rest
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2011 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Front Driver Side
Part Number: 4L5Z-1024101-AAC
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Left; Arm Rest
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2011 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest
Part Number: 6L5Z-10644A22-AA
Product Specifications
- Other Name: Armrest Assembly; Seat Armrest
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Ford Ranger | FX4, Sport, STX, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest
Part Number: 1L5Z-10644A22-CAH
Product Specifications
- Other Name: Armrest Assembly; Seat Armrest
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Ranger | Edge, Splash, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest
Part Number: 4L5Z-10644A22-DAC
Product Specifications
- Other Name: Armrest Assembly; Seat Armrest
- Replaces: 4L5Z-10644A22-DAB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Ranger | Sport, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Front Driver Side
Part Number: 4L5Z-1024101-AAG
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Left; Arm Rest
- Position: Front Driver Side
- Replaces: F57Z-1024101-AAZ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2003 Ford Ranger | Edge, Splash, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest
Part Number: 2L5Z-10644A22-CAA
Product Specifications
- Other Name: Armrest Assembly; Seat Armrest
- Manufacturer Note: with cupholder , ,with 60/40 split bench seat
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Ranger | Edge, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Front Passenger Side
Part Number: 3L5Z-1024100-AAA
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Right; Arm Rest
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2008 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Front Driver Side
Part Number: 3L5Z-1024101-AAA
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Left; Arm Rest
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2008 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Front Passenger Side
Part Number: 4L5Z-1024100-AAA
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Right; Arm Rest
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2011 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Front Passenger Side
Part Number: 4L5Z-1024100-AAB
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Right; Arm Rest
- Position: Front Passenger Side
- Replaces: 1L5Z-1024100-AAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2008 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Front Passenger Side
Part Number: 4L5Z-1024100-AAC
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Right; Arm Rest
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2011 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Front Passenger Side
Part Number: 4L5Z-1024100-AAG
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Right; Arm Rest
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2003 Ford Ranger | Edge, Splash, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Front Driver Side
Part Number: 4L5Z-1024101-AAD
Product Specifications
- Other Name: Pad - Armrest; Door Armrest, Front Left; Arm Rest
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2008 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest
Part Number: 4L5Z-10644A22-AAB
Product Specifications
- Other Name: Armrest Assembly; Seat Armrest
- Manufacturer Note: (QP)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2009 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest
Part Number: 4L5Z-10644A22-CAA
Product Specifications
- Other Name: Armrest Assembly; Seat Armrest
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2009 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest
Part Number: 4L5Z-13644A22-AAA
Product Specifications
- Other Name: Armrest Assembly; Seat Armrest
- Manufacturer Note: (TF)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2009 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest
Part Number: AL5Z-10644A22-AA
Product Specifications
- Other Name: Armrest Assembly; Seat Armrest
- Manufacturer Note: (QF)
- Replaces: 4L5Z-10644A22-AAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011, 2004-2005 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest, Driver Side
Part Number: F37Z1024101BAB
Product Specifications
- Other Name: Pad - Armrest Red; Arm Rest; Pad - Armrest
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford Ranger | Splash, Sport, STX, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Armrest Assembly
Part Number: F37Z10644A22ABD
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford Ranger | Splash, Sport, STX, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS

| Page 1 of 2 |Next >

1-20 of 32 Results

Ford Ranger Armrest

Welcome to our website where you can discover high-quality, genuine Ford Ranger Armrest. We offer an extensive inventory of OEM Ford Ranger Armrest at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Ford Ranger Armrest Parts Questions & Experts Answers

Armrest
3L5Z-10644A22-AAC
Q: How to service the 60 percent bench seat armrest on Ford Ranger?
A: The first step for servicing the 60 percent bench seat armrest requires depowering the supplemental restraint system (SRS) to maintain safety because the safety belt pretensioner operates using pyrotechnics. Safety glasses must be worn by everyone during this operation. Mark the position of safety belt buckle pretensioner wire harness connections as you remove the 60 percent bench seat and write down routing paths which will be needed for reinstallation. First disconnect the safety belt buckle pretensioner electrical connector after removing its anchor clips. Then guide the wire harness through the seat frame. The safety belt buckle pretensioner cover screw needs removal followed by the cover together with the removing of the safety belt buckle pretensioner nut to complete the operation. Unfasten J-clips from the beginning then unfasten the rear armrest J-clip followed by the hook and loop strip while guiding material toward the tether anchor. Users need to first raise the cushion cover with foam pad section and locate the armrest bolts before removing these four bolts to extract the armrest assembly. First disconnect the two armrest bracket bolts before sliding off the respective covers while releasing the bracket cover clips. To install the component begin by reversing the uninstallation procedure starting with the armrest assembly followed by the two armrest bracket bolts then the two armrest bracket covers and finishing with the armrest brackets. Mount the seat cushion foam pad and put on the cover before reattaching the tether anchor material and securing both hook and loop strip and rear armrest J-clip. You should apply the J-clips before putting on the safety belt buckle pretensioner and tightening its nut. After placing back the safety belt buckle pretensioner cover and screw you should connect the safety belt buckle pretensioner wire harness to the seat while securing the clips and electrical connector at its cushion pan. Reinstall the 60 percent bench seat then activate the SRS power while checking for complete functionality without defects until vehicle release.