How to Service and Repair Blower Control Switches on Lincoln Town Car?

Starting the blower motor switch and speed control repair process requires draining the engine cooling system. Begin by removing the right-hand cowl grille along with both screws on the two right-hand cowl grille. The service requires separating the EVAP canister purge valve electrical connector before removing the bracket nuts which need to be tightened to 6 Nm (53 lb-in) when reinstalling them. The service requires that you first remove the two Evaporative Emission canister purge valve fittings before releasing the two heater outlet hose clamps to take off the heater outlet hose. You must first release the heater core inlet clamp before discharging the heater inlet hose from the heater core. Reattach the heater tube bracket nut and stud at the engine's rear part by tightening it to 12 Nm (106 lb-in). First disconnect the electrical connector of the blower motor speed control and then remove the control by taking out its screw followed by the nut. The installation concludes by following the reverse order of the removal phase while cleaning and applying lubrication to the system using plain water and maintaining the correct engine coolant level.

OEM Lincoln Town Car Blower Control Switches

HVAC Control Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Blower Control Switches found

View related parts
Lincoln Town Car Vacuum Control Valve Part Number: FOVY-19B888-A
Product Specifications
- Other Name: Valve Assembly - Vacuum Control; Vacuum Mode Switch
- Manufacturer Note: WITH ATC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1991-1992 Lincoln Town Car | Base, Cartier, Cypress, Executive, Signature, Touring Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Temperature Control Part Number: 7W1Z-19980-A
Product Specifications
- Other Name: Control; Climate Control Module; Blower Control Switch; Dash Control Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Lincoln Town Car | Designer Series, Executive, Executive L, Signature, Signature L, Signature Limited | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Temperature Control Part Number: 6W1Z-19980-AA
Product Specifications
- Other Name: Control; Climate Control Module; Blower Control Switch; Dash Control Unit
- Replaces: 5W1Z-19980-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2006 Lincoln Town Car | Cartier, Cartier L, Designer Series, Executive, Executive L, Executive Protection Series, Protection Series, Signature, Signature L, Signature Limited, Ultimate, Ultimate L | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Blower Motor Switch Part Number: FOVY-19986-B
Product Specifications
- Other Name: Switch Assembly; Climate Control Module; Blower Control Switch; Blower Motor Resistor
- Manufacturer Note: ATC microprocessor., with ATC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1991-1994 Lincoln Town Car | Base, Cartier, Cypress, Executive, Jack Nicklaus, Signature, Touring Edition, Tournament Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Blower Motor Switch Part Number: E4VY-19986-A
Product Specifications
- Other Name: Switch Assembly; Climate Control Module; Blower Control Switch; Blower Motor Resistor
- Manufacturer Note: WITH ATC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1990 Lincoln Town Car | Base, Cartier, Cypress, Executive, Signature, Signature SE, Touring Edition | 8 Cyl 5.0 L GAS
View related parts
Lincoln Town Car Vacuum Control Valve Part Number: E1LY-19B888-A
Product Specifications
- Other Name: Valve Assembly - Vacuum Control
- Manufacturer Note: WITH ATC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1990 Lincoln Town Car | Base, Cartier, Cypress, Executive, Signature, Signature SE, Touring Edition | 8 Cyl 5.0 L GAS
View related parts
Lincoln Town Car Temperature Control Part Number: 1W1Z-19980-AA
Product Specifications
- Other Name: Control; Climate Control Module; Blower Control Switch; Dash Control Unit
- Replaces: YW1Z-19980-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Lincoln Town Car | Cartier, Cartier L, Executive, Executive L, Signature | 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Dash Control Unit Part Number: FOVY-19980-A
Product Specifications
- Other Name: Control; Climate Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1992 Lincoln Town Car | Base, Cartier, Cypress, Executive, Signature, Touring Edition | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
Lincoln Town Car Temperature Control Part Number: F6VZ-19980-AB
Product Specifications
- Other Name: Control; Climate Control Module; Blower Control Switch; Dash Control Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Lincoln Town Car | Anniversary, Base, Cartier, Cypress, Executive, Signature, Touring Edition | 8 Cyl 4.6 L GAS

Lincoln Town Car Blower Control Switches

OEM Blower Control Switches boasts unmatched quality. Each part goes through full quality checks. They adhere to Lincoln's official factory standards. These steps remove flaws and inconsistencies. So you can get Blower Control Switches with long life and a perfect fit. Come to our website and find genuine Lincoln Town Car parts. We keep a wide inventory of OEM Town Car parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Lincoln Town Car Blower Control Switches are among the parts that have a main purpose of improving convenience of the driver and passengers by allowing them to control the climate inside the car. These switches are quite popular due to their usage in the heating and AC systems thus enabl,ng the drivers to control the speed of the fans and hence maintain the thermal comfort of all people in the vehicle. The Lincoln Town Car model produced between 1981 and 2011 is compatible with several models and therefore the Blower Control Switches can be said to be versatile especially in enhancing efficiency and safety in all those models. These switches are combined with the blower motor to work efficiently so that different areas of a human body can be managed depending on the temperature change wanted by the client. This feature not only makes the traveling comfortable but it is also helpful for making the visibility clear through defrosting or cooling the glass. Lincoln Town Car Blower Control Switches have certain unique features that make them well suited for the automobile market: high durability and simplicity of the controls, which show the concern of Lincoln for quality and its creativity. These switches give priority to glamour and power and therefore epitomize Lincoln Town Car, and would therefore be important in its legacy. Therefore, the Lincoln Town Car Blower Control Switches are not simple parts; they are a part of that prestige that identifies Lincoln cars as vehicles that promise an optimal riding experience.

Lincoln Town Car Blower Control Switches Parts and Q&A

Temperature Control
7W1Z-19980-A
Q: How to Service and Repair Blower Control Switches on Lincoln Town Car?
A:
Starting the blower motor switch and speed control repair process requires draining the engine cooling system. Begin by removing the right-hand cowl grille along with both screws on the two right-hand cowl grille. The service requires separating the EVAP Canister Purge Valve electrical connector before removing the bracket nuts which need to be tightened to 6 Nm (53 lb-in) when reinstalling them. The service requires that you first remove the two Evaporative Emission canister purge valve fittings before releasing the two heater outlet hose clamps to take off the heater outlet hose. You must first release the heater core inlet clamp before discharging the heater inlet hose from the heater core. Reattach the heater tube bracket nut and stud at the engine's rear part by tightening it to 12 Nm (106 lb-in). First disconnect the electrical connector of the blower motor speed control and then remove the control by taking out its screw followed by the nut. The installation concludes by following the reverse order of the removal phase while cleaning and applying lubrication to the system using plain water and maintaining the correct engine coolant level.