How to Service and Repair Automatic Transmission Shift Levers for the Floor Shift on Mercury Grand Marquis?

Service and repair of floor shift automatic transmission shift levers require a procedure to deplete back up power first to avoid air bag deployment; disconnect the battery ground cable and keep it off for one minute while also taking down auxiliary batteries and power supplies. Start by detachment of both the instrument panel finish panel and electrical connector while also raising and removing the console finish panel. The shift handle bezel requires downward displacement to detach the transmission control harness. After this step, users should remove the two retaining screws to separate the shift handle. Start by removing the bulb from underneath the indicator bezel by lifting the bezel up then release the interlock cable housing clip before disconnecting the interlock cable. The first step entails separating the automatic transmission shift lever cable from the automatic transmission shift lever assembly followed by letting go of the automatic transmission shift lever cable housing clip. You must pull back the electrical connector pushpin retainer before freeing the electrical connector and disconnecting the vacuum line from the parking brake release unit. Begin by taking out the four nuts keeping the automatic transmission shift lever mounted to the floorboard before extracting the automatic transmission shift lever component while applying 11 Nm (8 lb-ft) of torque to it when reinstalling. To install the automatic transmission shift lever cable you must check that the locking tabs are engaged while fitting the cable end onto the ball stud before gently pressing the cable into the bracket until it clicks and verifying its locked position. After removing the covering hardware run the installation procedures backward to finish the operation.

OEM Mercury Grand Marquis Automatic Transmission Shift Levers

Automatic Transmission Shifter

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Automatic Transmission Shift Levers found

View related parts
Mercury Grand Marquis Shift Lever, Graystone Part Number: 8W1Z-7210-AA
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Replaces: 5W1Z-7210-AAL
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shift Lever Part Number: XW7Z-7210-AA
Product Specifications
- Other Name: Lever - Transmission; Gear Shift Assembly; Lever - Transmission Gear Shift
- Replaces: F8AZ-7210-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shift Lever, Camel Part Number: 8W1Z-7210-AB
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Replaces: 5W1Z-7210-AAJ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shift Lever, Black/Charcoal Part Number: 8W1Z-7210-AC
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Replaces: 5W1Z-7210-AAK
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shift Lever, Black Part Number: XW7Z-7210-AMB
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Manufacturer Note: Includes knob, o/drv. switch and wire assembly, with Midnight Black seal., with boot
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Mercury Grand Marquis | GS, LS, LSE | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shift Lever Part Number: 8W1Z-7210-AJ
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Grand Marquis | GS, GSL, Limited Edition, LS, Ultimate Edition | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shift Lever, Black Part Number: 8W1Z-7210-AE
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Replaces: 5W1Z-7210-AAD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Grand Marquis | GS, GSL, Limited Edition, LS, Ultimate Edition | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shift Lever Part Number: 8W1Z-7210-AD
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Grand Marquis | GS, GSL, Limited Edition, LS, Ultimate Edition | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shift Lever Part Number: XW7Z-7210-AAA
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Manufacturer Note: Includes knob, o/drv. switch and wire assembly, with Light Flint seal., with boot
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Mercury Grand Marquis | GS, LS, LSE | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shift Lever Part Number: F5AZ-7210-A
Product Specifications
- Other Name: Lever - Transmission; Gear Shift Assembly; Lever - Transmission Gear Shift
- Manufacturer Note: Includes knob, o/drv. switch and wire assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1997 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS

Mercury Grand Marquis Automatic Transmission Shift Levers

OEM Automatic Transmission Shift Levers boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Automatic Transmission Shift Levers with long life and a perfect fit. Come to our website and find genuine Mercury Grand Marquis parts. We keep a wide inventory of OEM Grand Marquis parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Mercury Grand Marquis Automatic Transmission Shift Levers Parts and Q&A

Shift Lever, Black/Charcoal
8W1Z-7210-AC
Q: How to Service and Repair Automatic Transmission Shift Levers for the Floor Shift on Mercury Grand Marquis?
A:
Service and repair of floor shift automatic transmission shift levers require a procedure to deplete back up power first to avoid air bag deployment; disconnect the battery ground cable and keep it off for one minute while also taking down auxiliary batteries and power supplies. Start by detachment of both the instrument panel finish panel and electrical connector while also raising and removing the console finish panel. The shift handle bezel requires downward displacement to detach the transmission control harness. After this step, users should remove the two retaining screws to separate the shift handle. Start by removing the bulb from underneath the indicator bezel by lifting the bezel up then release the interlock cable housing clip before disconnecting the interlock cable. The first step entails separating the automatic transmission shift lever cable from the automatic transmission shift lever assembly followed by letting go of the automatic transmission shift lever cable housing clip. You must pull back the electrical connector pushpin retainer before freeing the electrical connector and disconnecting the vacuum line from the parking brake release unit. Begin by taking out the four nuts keeping the automatic transmission shift lever mounted to the floorboard before extracting the automatic transmission shift lever component while applying 11 Nm (8 lb-ft) of torque to it when reinstalling. To install the automatic transmission shift lever cable you must check that the locking tabs are engaged while fitting the cable end onto the ball stud before gently pressing the cable into the bracket until it clicks and verifying its locked position. After removing the covering hardware run the installation procedures backward to finish the operation.