How to Service and Repair the ABS Control Module on Mercury Mountaineer?

Workers performing service or repair tasks on the Electronic Brake Control Module ABS Module will first need to follow safety procedures because brake fluid contains polyglycol ethers and polyglycols which can injure eyes and damage paint and plastic components. Eyes that encounter brake fluid require donation with 15 minutes of running water followed by medical care if irritation does not resolve itself. When someone consumes brake fluid they need to drink water followed by vomiting then obtain emergency medical assistance. Stow break fluid carefully to prevent leaks then use water for cleaning any surfaces that came into contact with it. Electronic modules react to electric charges so exposure of the ABS module can cause damage to it. A new ABS module needs as-built data configuration and calibration using diagnostic tools according to manufacturer's procedures. Begin the removal sequence by removing the hydraulic control unit (HCU) followed by the removal of components in the correct order. The reverse sequence of removal procedures should be followed to finish up the installation.

How to Bleed the Brake System After Installing a New ABS Control Module on Mercury Mountaineer?

When installing a new four-wheel anti-lock brake (4WABS) hydraulic control unit (HCU) users need to plug in the scan tool DCL cable adapter to the vehicle data link connector (DLC) under the dash before starting the bleeding process as per scan tool instructions. Begin by cleansing the brake master cylinder filler cap followed by its removal for fluid filling of the correct brake fluid into the reservoir. Installation requires the RH rear bleeder screw to receive a drain tube with its other end submerged in recommended brake fluid in a partial container. An assistant must pump the brake pedal while keeping up continuous pressure on it. You should open the RH rear bleeder screw until brake fluid starts to come out before tightening the screw beneath the pressure maintained by your helper. The braking operation requires you to maintain clear fluid production until the reservoir requires filling. Follow the bleeder screw tightening procedure starting with LH rear and then move to RH front and finally end with LH front. The conventional bleed procedure needs to be performed one last time for every corner following the above steps.

OEM Mercury Mountaineer ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 ABS Control Modules found

View related parts
Mercury Mountaineer Control Module Part Number: 7L2Z-2C215-A
$694.24 MSRP: $949.38
You Save: $255.14 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve; ABS Control Unit
- Replaces: 6L2Z-2C215-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: XL2Z-2C219-BA
$269.00 MSRP: $364.62
You Save: $95.62 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 7A2Z-2C219-E
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Replaces: 7A2Z-2C219-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 9L2Z-2C219-D
$490.32 MSRP: $664.62
You Save: $174.30 (27%)
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Replaces: AL2Z-2C219-C, 9L2Z-2C219-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mercury Mountaineer | Base, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 4L2Z-2B373-BD
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 5L2Z-2C219-A
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 5L2Z-2C219-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Mountaineer | Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer ABS Control Unit Part Number: F5TZ2C215B
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Hydraulic Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997 Mercury Mountaineer | Base | 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 4L1Z-2B373-AA
Product Specifications
- Other Name: Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Replaces: 2L1Z-2B373-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2004 Mercury Mountaineer | Base, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: F57Z-2C219-A
Product Specifications
- Other Name: Module & Bracket Assembly; ABS Control Module; Module & Brkt Assembly-Power Steering
- Manufacturer Note: ECU, 4 wheel ABS
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997 Mercury Mountaineer | Base | 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Pressure Valve Part Number: F87Z-2B373-AE
Product Specifications
- Other Name: Valve Assembly - Modulator; Brake Proportioning Valve; Modulator Valve; Valve Assembly; Proportioner Valve
- Replaces: F87Z-2B373-ARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer ABS Control Unit Part Number: XL2Z-2C215-AA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Hydraulic Unit
- Manufacturer Note: Hydraulic control unit only
- Replaces: F87Z-2C215-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Modulator Valve Part Number: 1L2Z-2C215-AA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 1L2Z-2C219-AA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 1L2Z-2C219-BA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Modulator Valve Part Number: 2C5Z-2C215-AA
Product Specifications
- Other Name: Module; ABS Control Module; ABS Control Unit
- Manufacturer Note: HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 2L2Z-2B373-AA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Modulator Valve Part Number: 2L2Z-2C215-AA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 3L2Z-2B373-DA
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 4L2Z-2B373-AD
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Control Module Part Number: 4L2Z-2B373-CB
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS

| Page 1 of 2 |Next >

1-20 of 22 Results

Mercury Mountaineer ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Mercury Mountaineer parts. We keep a wide inventory of OEM Mountaineer parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Mercury Mountaineer ABS Control Module is the part of anticlock braking system (ABS) that has been integrated into Mercury Mountaineer vehicles which is well known for its service excellence. This module also has a significant function in improving economy and stability by averting wheel lock during hard braking for vehicle control and to avoid slipping. Leveraging on split wheel speed sensors, the Mercury Mountaineer ABS Control Module checks out potential lock conditions as its ECU changes brake pressure much more rapidly than a driver is capable of doing. This ABS Control Module can fit Mercury Mountaineer models made from 1996 to 2010, and this technology has three generations of growth which includes ESC and traction control, which helps in enhancing the adhesion of the car to the road during unfavorable conditions. High quality auto parts, luxurious interiors, powerful vehicle engine are some of the features that Mercury Mountaineer is known for, and the ABS Control Module is one amongst them that can promote better performance of the vehicle. Interestingly, though ABS has most of the time been known to decrease the overall stopping distances, it has been noted to increase the braking distances on soft ground thus making this technology a bit complicated. Another important improvement of the Mercury Mountaineer ABS Control Module is that it has an unique design and function, which refers to its importance in driver safety, that is why this is the part, which is critical for everyone, who owns Mercury Mountaineer and aims to have much more reliability and performance.

Mercury Mountaineer ABS Control Module Parts and Q&A

Modulator Valve
4L2Z-2C215-BA
Q: How to Service and Repair the ABS Control Module on Mercury Mountaineer?
A:
Workers performing service or repair tasks on the Electronic Brake Control Module ABS Module will first need to follow safety procedures because brake fluid contains polyglycol ethers and polyglycols which can injure eyes and damage paint and plastic components. Eyes that encounter brake fluid require donation with 15 minutes of running water followed by medical care if irritation does not resolve itself. When someone consumes brake fluid they need to drink water followed by vomiting then obtain emergency medical assistance. Stow break fluid carefully to prevent leaks then use water for cleaning any surfaces that came into contact with it. Electronic modules react to electric charges so exposure of the ABS module can cause damage to it. A new ABS module needs as-built data configuration and calibration using diagnostic tools according to manufacturer's procedures. Begin the removal sequence by removing the hydraulic control unit (HCU) followed by the removal of components in the correct order. The reverse sequence of removal procedures should be followed to finish up the installation.
Control Module
XL2Z-2C219-BA
Q: How to Bleed the Brake System After Installing a New ABS Control Module on Mercury Mountaineer?
A:
When installing a new four-wheel anti-lock brake (4WABS) hydraulic control unit (HCU) users need to plug in the scan tool DCL cable adapter to the vehicle data link connector (DLC) under the dash before starting the bleeding process as per scan tool instructions. Begin by cleansing the brake master cylinder filler cap followed by its removal for fluid filling of the correct brake fluid into the reservoir. Installation requires the RH rear bleeder screw to receive a drain tube with its other end submerged in recommended brake fluid in a partial container. An assistant must pump the brake pedal while keeping up continuous pressure on it. You should open the RH rear bleeder screw until brake fluid starts to come out before tightening the screw beneath the pressure maintained by your helper. The braking operation requires you to maintain clear fluid production until the reservoir requires filling. Follow the bleeder screw tightening procedure starting with LH rear and then move to RH front and finally end with LH front. The conventional bleed procedure needs to be performed one last time for every corner following the above steps.