How to remove and replace the engine mount on Mercury Mountaineer?

A hoist positioned vehicle requires neutral gear position and disconnecting battery cables for the start of engine mount removal and replacement. The installation requires removing the weather strip and bolt to set aside the power steering fluid reservoir then tightening everything to 7 Nm (62 lb-in) before completing reinstallation. Let your engine temperature decrease first before taking off the coolant expansion tank to stop air from entering the radiator while you disconnect the overflow hose and tighten its supporting bolts to 7 Nm (62 lb-in). The next step requires the removal of two bolts accompanied by unclipping the clips to extract the upper fan shroud before reinstalling with screws tightened to 7 Nm (62 lb-in). The Engine Lifting Bracket requires 42 Nm (31 lb-ft) tightening for its bolt before adding the Engine Support Bar while also installing the pair of Adapters for 303-290A. The LH engine mount requires removal via its bolt which needs tightening to 103 Nm (76 lb-ft) before reinstalling. After that disconnect the five pushpins and the RH inner fender splash shield. Replace the RH engine mount by first loosening the three nuts to 90 Nm (66 lb-ft) torque then raising the engine by 60 mm (2.36 in). AWD models need four bolts removal and two stabilizer bar brackets extraction to suspend the bar until setting torque to 55 Nm (41 lb-ft) at reassembly. Hang the assembly from a jack which should be set away from obstacles before performing any lower or upper motions and use a proper jack to stabilize the axle housing. Disconnect the axle housing vent tube and remove three bolts along with three flag nuts then lower the housing 25 mm (1 in) and retighten bolts to 66 Nm (49 lb-ft). To finish the installation normalize the reinstallation of the LH engine mount nut while tightening it to 90 Nm (66 lb-ft) and proceed with the removal procedure in reverse order.

How to service and repair the engine mount on Mercury Mountaineer?

Service and repair procedures for the engine mount must start with fan shroud removal. You should first remove the LH engine insulator nuts before proceeding to remove the RH engine insulator nuts. Support the vehicle through lifting and remove all LH and RH engine support insulator nuts. The next step is to raise the engine before you support it while uninstalling the engine support insulators. After servicing the installation requires following the reverse steps of removal.

OEM Mercury Mountaineer Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Engine Mounts found

View related parts
Mercury Mountaineer Motor Mount, Driver Side Part Number: 7A2Z-6038-CA
$74.11 MSRP: $91.67
You Save: $17.56 (20%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount, Left; Engine Mount Bracket; Front Mount
- Position: Driver Side
- Replaces: 7A2Z-6038-C, 7A2Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Motor Mount, Passenger Side Part Number: 7A2Z-6038-D
$70.30 MSRP: $102.33
You Save: $32.03 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Right; Engine Mount Bracket; Front Mount; Engine Mount
- Position: Passenger Side
- Replaces: 5L2Z-6038-AD, 7A2Z-6038-B, 5L2Z-6038-BB, 5L2Z-6038-AB, 6L2Z-6038-AB, 5L2Z-6038-BD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Motor Mount Bracket Part Number: 5L2Z-6031-BA
$22.74 MSRP: $31.46
You Save: $8.72 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Right; Motor Mount; Bracket - Engine Mounting; Engine Mount Bracket
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Mount Bracket, Driver Side Part Number: F87Z-6031-FA
$59.45 MSRP: $86.53
You Save: $27.08 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Engine Mount Bracket, Left; Motor Mount; Motor Mount Bracket; Engine Mount Bracket
- Position: Driver Side
- Replaces: F77Z-6031-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Motor Mount, Driver Side Part Number: 6L2Z-6031-BA
$28.44 MSRP: $39.34
You Save: $10.90 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Engine Mount Bracket, Left; Engine Mount, Left; Motor Mount Bracket; Front Mount; Bracket; Engine Mount Bracket
- Position: Driver Side
- Replaces: 7A2Z-6031-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Transmission Mount Part Number: 5L2Z-6068-CA
$64.37 MSRP: $89.05
You Save: $24.68 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount.; Rear Mount
- Replaces: 1L2Z-6068-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Transmission Mount Part Number: 9L2Z-6068-A
$82.77 MSRP: $114.51
You Save: $31.74 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount.; Rear Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mercury Mountaineer | Premier | 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Transmission Mount Part Number: 5L2Z-6068-BA
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount.; Rear Mount
- Replaces: 1L2Z-6068-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Motor Mount, Driver Side Part Number: 5L2Z-6038-BC
Product Specifications
- Other Name: Insulator Assembly - Engine; Engine Mount, Left; Engine Mount Bracket; Front Mount; Insulator Assembly - Engine Support
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Transmission Mount Part Number: 8L2Z-6068-A
$33.37 MSRP: $47.33
You Save: $13.96 (30%)
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount.; Rear Mount
- Replaces: 7A2Z-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Motor Mount, Driver Side Part Number: 3L2Z-6038-BA
Product Specifications
- Other Name: Insulator Assembly - Engine; Engine Mount, Left; Engine Mount Bracket; Front Mount; Insulator Assembly - Engine Support
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Motor Mount, Passenger Side Part Number: 3L2Z-6038-BB
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Right; Engine Mount Bracket; Front Mount; Engine Mount
- Position: Passenger Side
- Replaces: F5TZ-6038-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Transmission Mount Part Number: 5L2Z-6068-DA
Product Specifications
- Other Name: Insulator Assembly - Engine; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Insulator Assembly - Engine Support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Motor Mount Bracket, Passenger Side Part Number: 6L2Z-6030-AA
Product Specifications
- Other Name: Bracket; Engine Mount Bracket, Right; Motor Mount; Engine Mount Bracket
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Luxury, Premier | 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Motor Mount, Passenger Side Part Number: F87Z-6038-HA
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Right; Engine Mount Bracket; Front Mount
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Transmission Mount Part Number: F87Z-6068-DA
Product Specifications
- Other Name: Insulator Assembly - Engine; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Insulator Assembly - Engine Support
- Manufacturer Note: AWD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Transmission Mount Part Number: F87Z-6068-KA
Product Specifications
- Other Name: Insulator Assembly - Engine; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Insulator Assembly - Engine Support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Transmission Mount Part Number: 8L2Z-6068-B
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Transmission Mounts; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount
- Replaces: 6L2Z-6068-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Motor Mount, Driver Side Part Number: F87Z-6038-JA
Product Specifications
- Other Name: Insulator Assembly - Engine; Engine Mount, Left; Engine Mount Bracket; Front Mount; Insulator Assembly - Engine Support
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Transmission Mount Part Number: 8L2Z-6068-C
Product Specifications
- Other Name: Insulator Assembly - Engine; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Insulator Assembly - Engine Support
- Replaces: 6L2Z-6068-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mercury Mountaineer | Premier | 8 Cyl 4.6 L GAS

| Page 1 of 2 |Next >

1-20 of 23 Results

Mercury Mountaineer Engine Mount

OEM Engine Mount boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Engine Mount with long life and a perfect fit. Come to our website and find genuine Mercury Mountaineer parts. We keep a wide inventory of OEM Mountaineer parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Mercury Mountaineer Engine Mount is one of the best and an important part which has direct impact on Mercury Mountaineer which provides it maximum performance. This Engine Mount works to reduce the noise and vibration coming from the engine to provide a firm yet comfortable place for the engine and transaxle to be bolted to in the chassis. The compatibility with different models of Mercury Mountaineer automobile manufactured between 1996 and 2010 further appreciates the necessity and enrichment of vehicle safety and efficiency. For instance, the Mercury Mountaineer Engine Mount is fitted with hydraulic and even electronic "active" mounts that change stiffness in reparation to engine speed for superior, comfortable performance. These mounts may nevertheless have to be inspected for replacement over long periods of use owing to their durability: tardy but long-lasting. The Mercury Mountaineer with its luxury interior and high-wattage auto parts is a plus in having the Engine Mount in a lineup of mid-size luxury SUVS. Featuring some unique functions that helps to limit the possible movement of the engine and at the same time isolate vibrations, the Engine Mount is here to maintain the position of Mercury Mountaineer as one of the most comfortable and safe cars on the road.

Mercury Mountaineer Engine Mount Parts and Q&A

Motor Mount, Driver Side
7A2Z-6038-CA
Q: How to remove and replace the engine mount on Mercury Mountaineer?
A:
A hoist positioned vehicle requires neutral gear position and disconnecting Battery Cables for the start of engine mount removal and replacement. The installation requires removing the weather strip and bolt to set aside the power steering fluid reservoir then tightening everything to 7 Nm (62 lb-in) before completing reinstallation. Let your engine temperature decrease first before taking off the coolant expansion tank to stop air from entering the Radiator while you disconnect the overflow hose and tighten its supporting bolts to 7 Nm (62 lb-in). The next step requires the removal of two bolts accompanied by unclipping the clips to extract the upper Fan Shroud before reinstalling with screws tightened to 7 Nm (62 lb-in). The Engine Lifting Bracket requires 42 Nm (31 lb-ft) tightening for its bolt before adding the Engine Support Bar while also installing the pair of Adapters for 303-290A. The LH engine mount requires removal via its bolt which needs tightening to 103 Nm (76 lb-ft) before reinstalling. After that disconnect the five pushpins and the RH inner fender splash shield. Replace the RH engine mount by first loosening the three nuts to 90 Nm (66 lb-ft) torque then raising the engine by 60 mm (2.36 in). AWD models need four bolts removal and two stabilizer bar brackets extraction to suspend the bar until setting torque to 55 Nm (41 lb-ft) at reassembly. Hang the assembly from a jack which should be set away from obstacles before performing any lower or upper motions and use a proper jack to stabilize the axle housing. Disconnect the axle housing vent tube and remove three bolts along with three flag nuts then lower the housing 25 mm (1 in) and retighten bolts to 66 Nm (49 lb-ft). To finish the installation normalize the reinstallation of the LH engine mount nut while tightening it to 90 Nm (66 lb-ft) and proceed with the removal procedure in reverse order.
Mount Bracket, Driver Side
F87Z-6031-FA
Q: How to service and repair the engine mount on Mercury Mountaineer?
A:
Service and repair procedures for the engine mount must start with Fan Shroud removal. You should first remove the LH engine insulator nuts before proceeding to remove the RH engine insulator nuts. Support the vehicle through lifting and remove all LH and RH engine support insulator nuts. The next step is to raise the engine before you support it while uninstalling the engine support insulators. After servicing the installation requires following the reverse steps of removal.