My Garage
Cart
Make sure this part fits

Ford F87Z-6068-KA
Transmission Mount

1998-2006 Ford F87Z6068KA

Customer Questions & Expert Answers (18)
Ford F87Z-6068-KA Transmission Mount
  • Part Description
    Insulator Assembly - Engine; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount
  • Base No.
    6068
  • Manufacturer
    Ford
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    1998-2001 Ford ExplorerEddie Bauer, Limited, Postal, Sport, XL, XL Fleet, XLS, XLT6 Cyl 4.0 L GAS
    2001-2003 Ford Explorer SportBase, XLS, XLT6 Cyl 4.0 L GAS
    2001-2005 Ford Explorer Sport TracAdrenalin, Base, XL, XLS, XLT6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS
    1998-2006 Ford RangerEdge, FX4, Splash, Sport, STX, Tremor, XL, XLT6 Cyl 4.0 L GAS
    1998-2001 Mercury MountaineerBase6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you verify if F87Z-6068-KA is the right one for my car? Posted by FordPartsDeal Specialist
    A:
    Select Your Vehicle model to verify if part number F87Z-6068-KA fits your car.
    Posted by FordPartsDeal Specialist
    Q:
    How to service and repair the engine mount on Ford Explorer Sport? Posted by Customer
    A:
    You should start repair and servicing work on the engine mount by taking off the fan shroud. Start by uninstalling both left-hand engine insulator nuts before moving to the right-hand engine insulator nuts. Raising and stabilizing the vehicle must be done before removing the LH and RH engine support insulator nuts. Rise the engine into position and support it before taking out the engine support insulators. Finish the installation by doing the reverse steps of removal.
    Posted by FordPartsDeal Specialist
    Q:
    How do you secure the transmission mount after installation for the 2003 Ford Explorer Sport? Posted by Customer
    A:
    Install the transmission mount into the crossmember and tighten the nuts.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the first step to service and repair the transmission mount for the 2004 Ford Explorer Sport Trac? Posted by Customer
    A:
    Ensure the vehicle is in NEUTRAL and positioned on a hoist.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be removed after raising the transmission for the 2001 Ford Explorer? Posted by Customer
    A:
    Remove the bolts and the transmission insulator.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    How do you remove the rear driveshaft for the 2001 Ford Explorer Sport? Posted by Customer
    A:
    Take out the bolts to remove the rear driveshaft.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after accessing the left motor mount nut for the 2002 Ford Explorer Sport Trac? Posted by Customer
    A:
    Remove the LH and RH engine support insulator nuts.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the next step after moving the 2001 Ford Explorer? Posted by Customer
    A:
    Raise and support the vehicle again and proceed to tighten the powertrain/drivetrain mount fasteners.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the procedure to detach the transmission mount for the 2002 Ford Explorer Sport Trac? Posted by Customer
    A:
    Detach the transmission mount by removing the screws.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the first step to service and repair the engine mount for the 2001 Ford Ranger? Posted by Customer
    A:
    Ensure that the electrical power to the air suspension system is turned off by switching off the air suspension switch.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the process for installing a new transmission mount for the 2002 Ford Ranger? Posted by Customer
    A:
    Position the new transmission mount on the extension housing and secure it with the mount-to-extension housing screws.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after disconnecting the battery for the 2001 Ford Ranger? Posted by Customer
    A:
    Raise and support the vehicle, ensuring to mark the rear driveshaft yoke and axle flange for proper alignment during reinstallation.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after installing the engine support insulator for the 2004 Ford Ranger? Posted by Customer
    A:
    Using a suitable floor crane, raise the engine and remove the Three-Bar Engine Support Kit.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Engine Mount
    Q:
    What should be done after moving the 2000 Ford Ranger? Posted by Customer
    A:
    Raise and support the vehicle again and proceed to tighten the powertrain/drivetrain mount fasteners.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Engine Mount
    Q:
    What should be done to ensure the correct balance of the rear driveshaft during installation for the 2004 Ford Ranger? Posted by Customer
    A:
    Align the rear driveshaft with the previously made marks and install the bolts.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    How do you ensure the driveshaft is correctly balanced during reinstallation for the 2006 Ford Ranger? Posted by Customer
    A:
    Align the driveshaft with the previously made marks.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next step after removing the rear driveshaft for the 2005 Ford Ranger? Posted by Customer
    A:
    Remove the transmission mount nuts and raise the transmission for support.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the first step to service and repair the engine mount for the 2000 Mercury Mountaineer? Posted by Customer
    A:
    Begin by removing the fan shroud.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Engine Mount
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM Ford Transmission Mount F87Z-6068-KA Designed for Proper Fit and Performance

The Ford part F87Z-6068-KA Transmission Mount as a genuine Ford Engine Mount, Motor And Transmission Mount, Engine Torque Strut Mount component delivers both authenticity and reliability. This item carries a warranty from the manufacturer which guarantees 12-month, 12,000-mile of use. The Ford F87Z-6068-KA Transmission Mount is used with Ford Ranger, Explorer, Explorer Sport Trac vehicles and Mercury Mountaineer models. The original Ford part will bear the manufacturer part number: F87Z-6068-KA and where it is made at Ford. It has the code: 6068.
This component is approximately 2.20 Pounds. The part F87Z6068KA is available in New condition while meeting the standards of the product rating. The Insulator Assembly - Engine; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount belongs to the Direct Replacement category to guarantee it is suitable for its specific vehicle applications. This part F87Z-6068-KA can be known as Rear Mount; Insulator Assembly - Engine Support. The inventory reference for this item is SKU: F87Z-6068-KA. The Ford manufacturer issues a factory warranty for this component which ensures dependable operation and peak performance. You can find delivery and returns information on our Shipping Policy and Return Policy pages.
Original equipment manufacturer parts are of the top standards and their performance is outstanding and top notch. This is explained by the fact that they follow the official manufacturing techniques of Ford, use of premium material and meets high standards of quality. Our site is worth visiting, in case you need high-quality and affordable OEM Ford components. We promise the optimal priced Ford parts on a wide range. You can relax that all OEM products you buy from us include a manufacturer warranty and will be covered by our simple and easy-to-use return policy, so you will not worry about buying a part.