How to service and repair the front suspension wheel bearing and wheel hub on Mercury Mountaineer?

Service and repair of the front suspension wheel bearing and wheel hub starts by removing the wheel combined with tire from the vehicle. Put aside the initial halfshaft nut and replace it with a fresh nut before tightening it to 250 Nm (184 lb-ft). The Front Wheel Hub Remover will help you disconnect the outboard CV joint from the wheel hub. Avoid hanging the caliper with anchor plate from the brake hose at all costs by removing bolts then placing them aside before support them with mechanic's wire. The new installation requires tightening the bolts to reach 165 Nm (122 lb-ft). First remove the brake disc then disconnect and remove the wheel speed sensor harness electrical connector while removing the wheel speed sensor harness bracket bolt which needs to be discarded before tightening the new one to 8 Nm (71 lb-in). Disassemble the wheel bearing and hub assembly by removing the three bolts which should be discarded before installation of the new assembly where new bolts require a torque setting of 122 Nm (90 lb-ft). The installation process should end by performing the opposite sequence of removal steps.

OEM Mercury Mountaineer Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Wheel Bearings found

View related parts
Mercury Mountaineer Axle Bearing, Rear
Part Number: E3TZ-1225-AA
$15.23 MSRP: $22.17
You Save: $6.94 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Ball; Drive Axle Shaft Bearing, Rear; Wheel Bearing; Axle Bearings; Shaft Bearings; Axle Shaft Bearing; Bearing
- Position: Rear
- Replaces: E3TZ-1225-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Wheel Bearings, Front Outer
Part Number: B5A-1216-A
$20.03 MSRP: $28.42
You Save: $8.39 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cone And Roller - Bearing; Front Outer Wheel Bearing and Race Set; Taper Bearing Cone; Axle Bearing; Front Wheel Bearing; Outer Wheel Bearing; Outer Bearing; Bearing; Wheel Bearing
- Position: Front Outer
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Wheel Bearings, Rear
Part Number: 6L2Z-1215-A
$54.14 MSRP: $90.73
You Save: $36.59 (41%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Wheel Hub; Wheel Bearing and Race Set, Rear; Wheel Bearing, Rear; Axle Bearing; Bearing; Wheel Bearing
- Position: Rear
- Replaces: 3L2Z-1215-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Wheel Bearing
Part Number: DV6Z-4221-A
$16.00 MSRP: $23.28
You Save: $7.28 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Ball; Differential Bearing; Axle Bearing; Front Wheel Bearing; Axle Bearings; Differential Bearings; Outer Bearing; Side Bearings; Bearing
- Replaces: B7A-4221-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Front Hub & Bearing
Part Number: 4L2Z-1102-AC
$118.24 MSRP: $194.55
You Save: $76.31 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub; Wheel Hub Repair Kit; Wheel Hub
- Replaced by: G2MZ-1104-AE
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Hub & Bearing, Front
Part Number: G2MZ-1104-W
$167.40 MSRP: $281.82
You Save: $114.42 (41%)
ADD TO CART
Product Specifications
- Other Name: Hub Assembly - Wheel; Front Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit.; Hub Assembly; Front Hub & Bearing
- Position: Front
- Replaces: F5TZ-1104-A, F87Z-1104-CA, HUB-8
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS

Mercury Mountaineer Wheel Bearing

Welcome to our website where you can discover high-quality, genuine Mercury Mountaineer Wheel Bearing. We offer an extensive inventory of OEM Mercury Mountaineer Wheel Bearing at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Mercury Mountaineer Wheel Bearing Parts Questions & Experts Answers

Wheel Bearing
DV6Z-4221-A
Q: How to service and repair the front suspension wheel bearing and wheel hub on Mercury Mountaineer?
A: Service and repair of the front suspension wheel bearing and Wheel Hub starts by removing the wheel combined with tire from the vehicle. Put aside the initial halfshaft nut and replace it with a fresh nut before tightening it to 250 Nm (184 lb-ft). The Front Wheel Hub Remover will help you disconnect the outboard CV joint from the wheel hub. Avoid hanging the caliper with anchor plate from the brake hose at all costs by removing bolts then placing them aside before support them with mechanic's wire. The new installation requires tightening the bolts to reach 165 Nm (122 lb-ft). First remove the Brake Disc then disconnect and remove the wheel speed sensor harness electrical connector while removing the wheel speed sensor harness bracket bolt which needs to be discarded before tightening the new one to 8 Nm (71 lb-in). Disassemble the wheel bearing and hub assembly by removing the three bolts which should be discarded before installation of the new assembly where new bolts require a torque setting of 122 Nm (90 lb-ft). The installation process should end by performing the opposite sequence of removal steps.