How to service and repair the front Door Latch Assembly on Mercury Sable?

Service or repair of the front door latch requires you to first remove the trim panel and bolt before positioning the interior door handle to one side. Start by placing the watershield to the side then disconnect external mirror power supply in addition to removing keyless entry keypad and front door disarm switch power connections. The door module grommet should be pushed through while connecting window regulator and window switch connectors until you can reach the window glass clamp bolts. The window regulator and window switch electrical connectors should be disconnected after marking the forward window glass clamp bolt position since it requires passing through the wiring harness grommet hole. Use pliers to remove two window glass clamp bolts before raising the glass window up to final position with tape as prevention. You must start by taking off the door lock cylinder circlip yet keep the front door lock cylinder rod and pawl off to the side before extracting the front door lock cylinder pawl from its actuating rod. Open the yellow clip to detach the exterior door handle actuating rod from the front door latch and then remove all eleven bolts alongside the three front door latch bolts that will secure the door module in position. Separate the door ajar switch and door lock actuator electrical connectors after disconnecting the push button rod from the front door latch and removing its rain hat using a push pin. The interior door handle cable needs release from the latch before removing the front door latch from its bracket which might require removal of both the door lock actuator and door ajar switch. First position the door lock cylinder pawl along with the door disarm switch following door ajar switch and door lock actuator installation when required. Place the front door latch onto its bracket while joining the interior door handle cable to the latch then position the rain hat onto its designated place on the latch. Affix the push button rod to the front door latch before connecting both the door ajar switch and door lock actuator electrical connection wires. Position the door module before installing eleven bolts secured at 8 Nm (71 lb-in) while the three front door latch bolts should be tight to 12 Nm (9 lb-ft). When the exterior door handle meets specification the technician should install it and tighten the door latch before hanging the exterior door handle rod with the yellow clip to maintain free movement and prevent alignment problems. Install the exterior door handle actuating rod to the front door latch by sealing the yellow clip before following up with the front door lock cylinder actuating rod connection to the front door lock cylinder pawl. Place the two window glass clamp bolts on the window while it stays fully rearward in both clamps so you can tighten them to 8 Nm (71 lb-in). Feeder the wiring harness grommet through the door module and setup the keyless entry keypad along with the front door disarm switch electrical connector if present and also connect the exterior mirror electrical connector in case of equipment. You should first install the watershield followed by positioning the interior door handle before loosely installing the bolt. Prepare the front door trim panel before aligning its interior door handle pins to the front trim and installing the interior handle bolt while tightening it to 7 Nm (62 lb-in).

OEM Mercury Sable Door Latch Assembly

Door Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

27 Door Latch Assemblys found

View related parts
Mercury Sable Latch Assembly, Front Passenger Side
Part Number: 6C2Z-1521812-A
$138.65 MSRP: $213.97
You Save: $75.32 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch; Door Latch Assembly, Front Right; Door Lock; Lock; Door Latch Assembly
- Position: Front Passenger Side
- Replaces: 4C2Z-1521812-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Latch Assembly, Front Driver Side
Part Number: 6C2Z-1521813-A
$113.65 MSRP: $165.43
You Save: $51.78 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Latch; Door Latch Assembly, Front Left, Front Right; Door Lock; Lock; Door Latch Assembly
- Position: Front Driver Side
- Replaces: 4C2Z-1521813-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Lock Actuator, Front Driver Side
Part Number: 6L2Z-78218A43-B
$12.10 MSRP: $18.73
You Save: $6.63 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor, Front Left, Rear Left; Door Latch Assembly.; Actuator
- Position: Front Driver Side
- Replaces: 4L2Z-78218A43-AA, 6L2Z-78218A43-AB, 6L2Z-78218A43-A, 6L2Z-78218A43-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Lock Actuator, Rear Passenger Side
Part Number: 6L2Z-78218A42-B
$9.94 MSRP: $15.38
You Save: $5.44 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor, Front Right, Rear Right; Door Latch Assembly.; Actuator
- Position: Rear Passenger Side
- Replaces: 4L2Z-78218A42-AB, 6L2Z-78218A42-A, 6L2Z-78218A42-AA, 6L2Z-78218A42-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Lock Actuator, Front
Part Number: 5F1Z-14A626-AA
$28.18 MSRP: $38.99
You Save: $10.81 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly; Keyless Entry Keypad, Front; Door Lock Actuator Motor; Door Lock Actuator; Pad Assembly; Keyless Lock Pad
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Lock Actuator, Driver Side
Part Number: F8DZ-54218A43-A
$18.54 MSRP: $25.66
You Save: $7.12 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor; Door Lock Actuator; Actuator
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1998 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Latch Assembly, Rear Driver Side
Part Number: 6F1Z-5426413-A
$43.48 MSRP: $60.15
You Save: $16.67 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Stop - Contact Switch; Door Latch Assembly, Rear Left; Door Lock; Lock; Latch; Door Latch Assembly
- Position: Rear Driver Side
- Replaces: 3F1Z-5426413-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Lock Actuator
Part Number: F8DZ-5426594-A
$35.24 MSRP: $47.96
You Save: $12.72 (27%)
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor; Door Lock Actuator; Actuator
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Lock, Passenger Side
Part Number: F4OZ5426412B
$54.95 MSRP: $74.78
You Save: $19.83 (27%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly; Door Latch Assembly; Door Lock; Latch
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1989 Mercury Sable | GS, LS | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Latch Assembly, Rear Passenger Side
Part Number: 6F1Z-5426412-A
Product Specifications
- Other Name: Lock Assembly; Door Latch Assembly, Rear Right; Door Lock; Lock; Latch; Door Latch Assembly
- Position: Rear Passenger Side
- Replaces: XF1Z-5426412-AA, 3F1Z-5426412-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Latch Assembly, Front Passenger Side
Part Number: 9W7Z-5421812-B
Product Specifications
- Other Name: Latch; Door Latch Assembly, Front Right; Door Lock; Lock; Door Latch Assembly
- Position: Front Passenger Side
- Replaces: 6W7Z-5421812-B, 6W7Z-5421812-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Mercury Sable | GS, LS, LTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Lock Actuator, Rear Passenger Side
Part Number: F8AZ-5426594-A
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor, Rear Left, Rear Right; Door Lock Actuator Motor; Door Lock Actuator; Actuator
- Position: Rear Passenger Side
- Replaces: F8AZ-5426594-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1995 Mercury Sable | GS, LS, LTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Latch Assembly, Front Driver Side
Part Number: 8F9Z-74219A65-A
Product Specifications
- Other Name: Control; Door Latch Assembly, Front Left; Door Lock; Lock Module; Door Latch Assembly
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Latch Assembly, Rear Passenger Side
Part Number: 8F9Z-74264B52-A
Product Specifications
- Other Name: Latch; Door Latch Assembly, Rear Right; Door Lock; Door Latch Assembly
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Lock
Part Number: F4DZ5426412B
Product Specifications
- Other Name: Lock Assembly - Door; Door Latch Assembly; Door Lock
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Mercury Sable | GS, LS, LTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Lock, Rear Driver Side
Part Number: F5DZ5426413C
Product Specifications
- Other Name: Stop Contact Switch; Door Latch Assembly, Rear Left; Door Latch Assembly; Door Lock; Latch
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1995 Mercury Sable | GS, LS, LTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Lock, Passenger Side
Part Number: F6DZ-5421812-A
Product Specifications
- Other Name: Latch; Door Lock
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1998 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Lock Actuator, Passenger Side
Part Number: F8DZ-54218A42-A
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor; Door Lock Actuator; Actuator
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1998 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Control Assembly, Passenger Side
Part Number: F8DZ54264A00AAA
Product Specifications
- Other Name: Control; Door Lock
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Lock Assembly, Front Passenger Side
Part Number: 8F9Z-5421812-A
Product Specifications
- Other Name: Latch; Door Latch Assembly, Front Right; Door Lock; Lock; Door Latch Assembly
- Manufacturer Note: Includes Door Ajar Switch
- Position: Front Passenger Side
- Replaces: 7F9Z-5421812-A, 6F9Z-5421812-A, 6F9Z-5421812-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS

| Page 1 of 2 |Next >

1-20 of 27 Results

Mercury Sable Door Latch Assembly

Welcome to our website where you can discover high-quality, genuine Mercury Sable Door Latch Assembly. We offer an extensive inventory of OEM Mercury Sable Door Latch Assembly at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Mercury Sable Door Latch Assembly Parts Questions & Experts Answers

Lock Actuator, Front Driver Side
6L2Z-78218A43-B
Q: How to service and repair the front Door Latch Assembly on Mercury Sable?
A: Service or repair of the front door latch requires you to first remove the trim panel and bolt before positioning the interior Door Handle to one side. Start by placing the watershield to the side then disconnect external mirror power supply in addition to removing keyless entry keypad and front door disarm switch power connections. The door module grommet should be pushed through while connecting Window Regulator and window switch connectors until you can reach the window glass clamp bolts. The window regulator and window switch electrical connectors should be disconnected after marking the forward window glass clamp bolt position since it requires passing through the wiring harness grommet hole. Use pliers to remove two window glass clamp bolts before raising the glass window up to final position with tape as prevention. You must start by taking off the door lock cylinder circlip yet keep the front door lock cylinder rod and pawl off to the side before extracting the front door lock cylinder pawl from its actuating rod. Open the yellow clip to detach the exterior door handle actuating rod from the front door latch and then remove all eleven bolts alongside the three front door latch bolts that will secure the door module in position. Separate the door ajar switch and door lock actuator electrical connectors after disconnecting the push button rod from the front door latch and removing its rain hat using a push pin. The interior door handle cable needs release from the latch before removing the front door latch from its bracket which might require removal of both the door lock actuator and door ajar switch. First position the door lock cylinder pawl along with the door disarm switch following door ajar switch and door lock actuator installation when required. Place the front door latch onto its bracket while joining the interior door handle cable to the latch then position the rain hat onto its designated place on the latch. Affix the push button rod to the front door latch before connecting both the door ajar switch and door lock actuator electrical connection wires. Position the door module before installing eleven bolts secured at 8 Nm (71 lb-in) while the three front door latch bolts should be tight to 12 Nm (9 lb-ft). When the exterior door handle meets specification the technician should install it and tighten the door latch before hanging the exterior door handle rod with the yellow clip to maintain free movement and prevent alignment problems. Install the exterior door handle actuating rod to the front door latch by sealing the yellow clip before following up with the front door lock cylinder actuating rod connection to the front door lock cylinder pawl. Place the two window glass clamp bolts on the window while it stays fully rearward in both clamps so you can tighten them to 8 Nm (71 lb-in). Feeder the wiring harness grommet through the door module and setup the keyless entry keypad along with the front door disarm switch electrical connector if present and also connect the exterior mirror electrical connector in case of equipment. You should first install the watershield followed by positioning the interior door handle before loosely installing the bolt. Prepare the front door trim panel before aligning its interior door handle pins to the front trim and installing the interior handle bolt while tightening it to 7 Nm (62 lb-in).