How to service the right-hand exhaust manifold on Mercury Sable?

The service of the right-hand exhaust manifold starts with disconnecting the battery ground cable. A technician should remove the cowl vent screen along with the cowl extension before disconnecting the Oxygen Sensor (HO2S) electrical connector. Service begins by removing the exhaust manifold with its EGR valve tube and the exhaust manifold heat shield through bolt removal. First remove the bolts from the catalytic converter exhaust manifold connection before you obtain the six bolts holding the exhaust manifold in place to remove both components along with their gasket which must be thrown away. Installation begins by installing an exhaust manifold gasket before inserting the exhaust manifold on the bolts that need two-step tightening at 10 Nm (89 inch lbs.) followed by 22 Nm (16 ft. lbs.). Connect the catalytic converter through bolt installation and then proceed with the exhaust manifold heat shield installation using its respective bolts. Complete the installation by setting the exhaust manifold against the EGR valve tube then attach the HO2S electrical connector, replace the cowl vent screen and cowl extension before reattaching the battery ground cable.

How to service the left-hand side exhaust manifold on Mercury Sable?

Service of the left-hand side exhaust manifold starts with removing the LH exhaust manifold to pipe nuts along with the coolant tube bracket bolt. First disconnect the LH Heated Oxygen Sensor (HO2S) electrical connector which connects to the coolant tube while also unclipping the connector. Raise and support the vehicle. The service begins with pin-type retainer and bolt removal together with the front splash shield and continues with lower exhaust manifold nut removal as well as the coolant tube lower bracket bolt. The lower vehicle position gives access to remove upper nuts before removing the exhaust manifold with its original gasket needed for disposal. Place a new gasket in position before installing the exhaust manifold by using the sequence of specified nut tightening. After relocating the coolant tubes use a wrench to tighten the bolt while attaching the LH HO2S electroical connector and installing the LH exhaust manifold to pipe nuts. Proceed by uplifting the vehicle to install the coolant tube lower bracket bolt while concluding the process by placing and securing the front splash shield through bolt and pin-type retainer fasteners.

OEM Mercury Sable Exhaust Manifold

Engine Exhaust Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Exhaust Manifolds found

View related parts
Mercury Sable Exhaust Manifold, Passenger Side Part Number: 7T4Z-9430-C
$64.01 MSRP: $93.17
You Save: $29.16 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Right; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Exhaust Manifold, Driver Side Part Number: 4F1Z-9431-AA
$132.62 MSRP: $180.47
You Save: $47.85 (27%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Left; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold, Driver Side Part Number: 7T4Z-9431-C
$62.42 MSRP: $86.35
You Save: $23.93 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Left; Manifold
- Position: Driver Side
- Replaces: 7T4Z-9431-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Exhaust Manifold, Passenger Side Part Number: F4DZ9430B
$74.31 MSRP: $101.12
You Save: $26.81 (27%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1995 Mercury Sable | GS, LS, LTS | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold, Passenger Side Part Number: E6AZ9430F
$149.32 MSRP: $203.19
You Save: $53.87 (27%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1993 Mercury Sable | GS, LS | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold, Passenger Side Part Number: 4F1Z-9430-BA
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Right; Manifold
- Position: Passenger Side
- Replaces: 4F1Z-9430-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold, Driver Side Part Number: YF1Z-9431-GB
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Left; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Mercury Sable | LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold Part Number: E6AZ9430E
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986 Mercury Sable | GS | 4 Cyl 2.5 L GAS
View related parts
Mercury Sable Exhaust Manifold, Driver Side Part Number: F7DZ9431FB
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold, Passenger Side Part Number: F7DZ9430EA
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Manifold, Driver Side Part Number: F6DZ9431S
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold, Driver Side Part Number: F6DZ-9431-R
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Manifold, Passenger Side Part Number: F6DZ9430L
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold, Driver Side Part Number: F5DZ9431C
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1997 Mercury Sable | G, GS, LS | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold, Driver Side Part Number: F4DZ9431C
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1995 Mercury Sable | GS, LS, LTS | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Exhaust Manifold, Driver Side Part Number: F48Z9431E
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1988-1995 Mercury Sable | GS, LS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Exhaust Manifold, Driver Side Part Number: E6AZ9431E
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1993 Mercury Sable | GS, LS | 6 Cyl 3.0 L GAS

Mercury Sable Exhaust Manifold

OEM Exhaust Manifold boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Exhaust Manifold with long life and a perfect fit. Come to our website and find genuine Mercury Sable parts. We keep a wide inventory of OEM Sable parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Mercury Sable Exhaust Manifold is a crucial assembly kit with a great responsibility of boosting the performance and competence of the car. Known for its durability the function of Exhaust Manifold is to channel hot fumes from the engine to the exhaust system which in turn makes the engine to work fully and release few bad gases to the environment. Depending on the model of Sable and the presence of V6 engine, Mercury Sable Exhaust Manifold has several tubes that match the count of cylinders and facilitate gases circulation. Made of cast iron or stainless steel for endurance it seems to participate in the durability of the Mercury Sable. Its efficiency in regulating the air to fuel mixture in the engine is important in avoiding emission of dangerous gases thus improving safety of occupants. Also in the Mercury Sable Exhaust Manifold you find unique designs in the market that can be found for instance ceramic coating of heat in the engine bay. This attention is not only cute in enhance or boost the performance of the car but also assures that Sable is still the right car to be driven. Being a part of the setup with an outstanding performance record and compatibility of the Exhaust Manifold in relation to the several generations of the Mercury Sable is an element that underlines the vehicle as a reliable mid-size sedan that is hard to surpass.

Mercury Sable Exhaust Manifold Parts and Q&A

Exhaust Manifold, Passenger Side
4F1Z-9430-BA
Q: How to service the right-hand exhaust manifold on Mercury Sable?
A:
The service of the right-hand exhaust manifold starts with disconnecting the battery ground cable. A technician should remove the cowl vent screen along with the cowl extension before disconnecting the Oxygen Sensor (HO2S) electrical connector. Service begins by removing the exhaust manifold with its EGR valve tube and the exhaust manifold heat shield through bolt removal. First remove the bolts from the Catalytic Converter exhaust manifold connection before you obtain the six bolts holding the exhaust manifold in place to remove both components along with their gasket which must be thrown away. Installation begins by installing an exhaust manifold gasket before inserting the exhaust manifold on the bolts that need two-step tightening at 10 Nm (89 inch lbs.) followed by 22 Nm (16 ft. lbs.). Connect the catalytic converter through bolt installation and then proceed with the exhaust manifold heat shield installation using its respective bolts. Complete the installation by setting the exhaust manifold against the EGR valve tube then attach the HO2S electrical connector, replace the cowl vent screen and cowl extension before reattaching the battery ground cable.
Exhaust Manifold, Driver Side
YF1Z-9431-GB
Q: How to service the left-hand side exhaust manifold on Mercury Sable?
A:
Service of the left-hand side exhaust manifold starts with removing the LH exhaust manifold to pipe nuts along with the coolant tube bracket bolt. First disconnect the LH Heated Oxygen Sensor (HO2S) electrical connector which connects to the coolant tube while also unclipping the connector. Raise and support the vehicle. The service begins with pin-type retainer and bolt removal together with the front splash shield and continues with lower exhaust manifold nut removal as well as the coolant tube lower bracket bolt. The lower vehicle position gives access to remove upper nuts before removing the exhaust manifold with its original gasket needed for disposal. Place a new gasket in position before installing the exhaust manifold by using the sequence of specified nut tightening. After relocating the coolant tubes use a wrench to tighten the bolt while attaching the LH HO2S electroical connector and installing the LH exhaust manifold to pipe nuts. Proceed by uplifting the vehicle to install the coolant tube lower bracket bolt while concluding the process by placing and securing the front splash shield through bolt and pin-type retainer fasteners.