My Garage
Cart
Make sure this part fits

Ford 8L8Z-19E616-E
Motor

2005-2009 Ford 8L8Z19E616E

Customer Questions & Expert Answers (14)
Ford 8L8Z-19E616-E Motor
Ford 8L8Z-19E616-E Motor
  • Part Description
    Motor Assembly; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator
  • Base No.
    19E616
  • Replaced By
    AL8Z-19E616-F
  • Manufacturer
    Ford
Make sure this part fits
$27.09 MSRP: $43.02
You Save: $15.93 (38%)
Ships in 1 Business Day
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2005-2007 Ford EscapeHybrid4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)
    2008-2009 Ford F-250 Super DutyCabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.4 L DIESEL
    2008-2009 Ford F-350 Super DutyCabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.4 L DIESEL
    2006-2009 Mercury MarinerHybrid4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Will this 8L8Z-19E616-E work in my car? Posted by FordPartsDeal Specialist
    A:
    Select Your Vehicle model to verify if part number 8L8Z-19E616-E fits your car.
    Posted by FordPartsDeal Specialist
    Q:
    How to remove and replace the temperature blend door actuator on Mercury Mariner? Posted by Customer
    A:
    The first step to replace a temperature blend door actuator requires glove compartment door lowering and selecting full cold on the temperature dial. Detach the temperature blend door actuator from its position on the blend door shaft following which you should release the locking tab. Start by removing the finish panel of the instrument center and extracting the blend door temperature actuator. Reinstallation of the new actuator requires following the reverse steps from the removal process.
    Posted by FordPartsDeal Specialist
    Q:
    What is the first step to service the temperature blend door actuator for the 2006 Ford Escape? Posted by Customer
    A:
    Lower the glove compartment door and turn the temperature selector to the full cold position.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the first step to service and repair the recirculation blend door actuator for the 2005 Ford Escape? Posted by Customer
    A:
    Begin by removing the instrument panel.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the first step to remove the vacuum control motor for the 2007 Ford Escape? Posted by Customer
    A:
    Disconnect the vacuum supply hose.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should be done after removing the heater core and evaporator core housing for the 2009 Ford F-250 Super Duty? Posted by Customer
    A:
    Take out the floor duct screw and then the floor duct itself.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    How do you complete the installation after removing the actuator for the 2008 Ford F-250 Super Duty? Posted by Customer
    A:
    Reverse the steps taken during removal.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    How do you disconnect the left-hand temperature blend door actuator for the 2008 Ford F-350 Super Duty? Posted by Customer
    A:
    Disconnect the electrical connector from the left-hand temperature blend door actuator.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should be done after lowering the glove compartment for the 2008 Ford F-250 Super Duty? Posted by Customer
    A:
    Take out the two screws securing the air inlet mode door actuator and disconnect its electrical connector.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the final step after removing the RH temperature blend door actuator for the 2008 Mercury Mariner? Posted by Customer
    A:
    Install the new actuator by reversing the removal steps.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should be done for installation for the 2007 Mercury Mariner? Posted by Customer
    A:
    Reverse the removal procedure.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the purpose of the LH temperature blend door actuator for the 2009 Mercury Mariner? Posted by Customer
    A:
    It is used in dual-zone Electronic Automatic Temperature Control (EATC) vehicles to manage the left side temperature blend door.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the first step to service the recirculation blend door actuator for the 2006 Mercury Mariner? Posted by Customer
    A:
    Begin by removing the instrument panel.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    How do you complete the installation after removing the actuator for the 2009 Ford F-350 Super Duty? Posted by Customer
    A:
    Reverse the steps taken during removal.
    Posted by FordPartsDeal Specialist
    See expert answers on similar Blend Door Actuator
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM Ford Motor 8L8Z-19E616-E Designed for Proper Fit and Performance

The Ford part 8L8Z-19E616-E Motor as a genuine Ford Blend Door Actuator component delivers both authenticity and reliability. This item carries a warranty from the manufacturer which guarantees 12-month, 12,000-mile of use. The Ford 8L8Z-19E616-E Motor is used with Ford Escape, F-350 Super Duty, F-250 Super Duty vehicles and Mercury Mariner models. The original Ford part will bear the manufacturer part number: 8L8Z-19E616-E and where it is made at Ford. It has the code: 19E616.
This component has dimensions of 8.2 x 6.2 x 1.1 inches and its weight is approximately 0.50 Pounds. The part 8L8Z19E616E is available in New condition while meeting the standards of the product rating. The Motor Assembly; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator belongs to the Direct Replacement category to guarantee it is suitable for its specific vehicle applications. This part 8L8Z-19E616-E serves as an alternative for AL8Z-19E616-F. The inventory reference for this item is SKU: 8L8Z-19E616-E. Additional manufacturer-provided details include: Pin #5 Is Not Used (No Connection). The Ford manufacturer issues a factory warranty for this component which ensures dependable operation and peak performance. You can find delivery and returns information on our Shipping Policy and Return Policy pages.
Original equipment manufacturer parts are of the top standards and their performance is outstanding and top notch. This is explained by the fact that they follow the official manufacturing techniques of Ford, use of premium material and meets high standards of quality. Our site is worth visiting, in case you need high-quality and affordable OEM Ford components. We promise the optimal priced Ford parts on a wide range. You can relax that all OEM products you buy from us include a manufacturer warranty and will be covered by our simple and easy-to-use return policy, so you will not worry about buying a part.