Other Name: Motor Assembly; HVAC Blend Door Actuator; HVAC Heater Blend Door Actuator; Vacuum Motor; Mode Motor; Motor
Replaces: AL3Z-19E616-A, 9L3Z-19E616-B, YH-1777
Fits the following Ford Models:
Expedition | 2009-2017 | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL Platinum, EL SSV, EL XL, EL XLT, King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX
F-150 | 2009-2014 | FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Limited, Platinum, STX, SVT Raptor, XL, XLT | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L CNG, 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L LPG, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L FLEX, 8 Cyl 5.4 L FLEX, 8 Cyl 6.2 L GAS
Other Name: Motor Assembly; HVAC Defrost, Floor, Air Inlet, and Heater Blend Door Actuators.; Adjust Motor
Manufacturer Note: Defrost/Panel/Floor Door
Replaces: YH-2065, FL3Z-19E616-F
Fits the following Ford Models:
Expedition | 2018-2024 | King Ranch, Limited, Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XL, Max XLT, Platinum, SSV, Timberline, XL, XL STX, XLT | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
F-150 | 2015-2023 | King Ranch, Lariat, Limited, Platinum, Police Responder, Raptor, Raptor R, SSV, Tremor, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX, 8 Cyl 5.2 L GAS
F-150 Lightning | 2022-2023 | Lariat, Platinum, Pro, Pro SSV, XLT | BATTERY EV (EV/BEV)
F-250 Super Duty | 2017-2024 | King Ranch, Lariat, Limited, Platinum, XL, XLT | 8 Cyl 6.2 L FLEX, 8 Cyl 6.7 L DIESEL, 8 Cyl 6.8 L FLEX, 8 Cyl 6.8 L GAS, 8 Cyl 7.3 L GAS
F-350 Super Duty | 2017-2024 | King Ranch, Lariat, Limited, Platinum, XL, XLT | 8 Cyl 6.2 L FLEX, 8 Cyl 6.7 L DIESEL, 8 Cyl 6.8 L GAS, 8 Cyl 7.3 L GAS
Bronco Sport | 2021-2023 | Badlands, Base, Big Bend, First Edition, Heritage Edition, Heritage Limited Edition, Outer Banks | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS
Escape | 2020-2023 | Active, Base, Platinum, Platinum Hybrid, Plug-In Hybrid, S, SE, SE Hybrid, SE Plug-In Hybrid, SE Sport Hybrid, SEL, SEL Hybrid, SEL Plug-In Hybrid, ST-Line, ST-Line Elite, ST-Line Elite Hybrid, ST-Line Hybrid, ST-Line Select, ST-Line Select Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
Explorer | 2020-2023 | Base, King Ranch, Limited, Limited Hybrid, Platinum, Platinum Hybrid, ST, ST-Line, Timberline, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)
Maverick | 2022-2023 | Lariat, XL, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
Mustang Mach-E | 2021-2023 | California Route 1, First Edition, GT, Premium, Select | BATTERY EV (EV/BEV)
Police Interceptor Utility | 2020-2023 | Base | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)
Q: How to service the Auxiliary Temperature Blend Door Actuator on Ford Explorer?
A: You should start to service the Auxiliary Temperature Blend Door Actuator by placing the vehicle in NEUTRAL mode while it is supported on a hoist. The LH quarter trim panel removal achieves the first step of the process while the following step includes eliminating the two auxiliary line floorpan bracket nuts that require an 8 Nm (71 lb-in) torque setting for installation. The two auxiliary housing bolts along with the auxiliary housing nut require removal but they need to be torqued to 7 Nm (62 lb-in) for the reinstallation process. Disconnect both the temperature blend door actuator electrical connector as well as the auxiliary harness electrical connector. You need to take out the temperature blend door actuator by removing its three securing screws. The completion of this process requires reversing the removal procedure steps.
Q: How to Service and Repair the Defrost Mode Blend Door Actuator on Ford Mustang?
A: The beginning step in repairing the defrost door mode door actuator requires depressing the glove compartment. The first step involves disconnecting the electrical connector which belongs to the defrost door mode door actuator. Secure the actuator with two screws then detach both screws completely before removing the actuator itself. The new actuator installation process will follow the steps that were used for removal.
Q: How to service the temperature blend door actuator on Ford Ranger?
A: The first step for servicing the temperature blend door actuator requires removal of the passenger air bag module and the defroster opening grill. The right-hand demister hose needs to be detached from its position before being set aside. Take out the screws which fasten the anti-theft or keyless entry module then store this module to the side. Access the actuator through the right-hand defroster nozzle opening and remove the screw by taking out the temperature blend door actuator after you disconnect its electrical connector and remove all screws. Installation of the new actuator should follow the same steps in reverse order to the uninstallation process.