How to Service and Repair the Rear Two-Piece Drive Shaft on 2004 Ford Excursion?

A proper service or repair of the rear two-piece driveshaft requires vehicle lifting and axle support before indexing the driveshaft at the axle flange to disconnect it by removing and discarding all bolts, U-joint retainers and mechanics wire support. Mechanics wire should be used for driveshaft support. The driveshaft needs disconnecting from the transfer case or transmission of four-wheel drive vehicles or vehicles with circular flanges while mechanics wire supports the removed bolts. You must mark the transmission output shaft position when dealing with a slip-yoke transmission system. Before continuing detach the bolts which stabilize the center bearing support and take off the driveshaft. Clean all grease deposits together with dirt and rust from driveshaft flange yoke areas and all driveshaft slip yoke surfaces. The examination of the driveshaft slip yoke boot for holes and tears requires replacement when needed while checking the driveshaft center bearing support for rough movement demands its replacement with a new component. Check the center bearing rubber insulator for degradation and unstable condition before making a necessary replacement. Check the transmission together with the transfer case along with the axle seals for damage to replace them when needed. During reinstallation of the driveshaft you must coat the slip yoke spline with grease while following the index marks from removal and using newly installed bolts and retainers with correct bolt direction for vehicle requirements. A reverse order of the removal method completes the installation.

OEM 2004 Ford Excursion Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Drive Shafts found

View related parts
2004 Ford Excursion Axle Shaft, Front Passenger Side
Part Number: 4C3Z-3219-BA
$454.45 MSRP: $667.33
You Save: $212.88 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Passenger Side
- Replaces: 3C3Z-3219-BA
- Item Weight: 35.40 Pounds
- Item Dimensions: 6.2 x 6.2 x 29.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3219-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2004 Ford Excursion Axle Shaft, Front Driver Side
Part Number: 4C3Z-3220-BA
$410.76 MSRP: $603.17
You Save: $192.41 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Driver Side
- Replaces: 3C3Z-3220-BA
- Item Weight: 34.90 Pounds
- Item Dimensions: 30.7 x 6.2 x 6.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3220-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2004 Ford Excursion Drive Shaft
Part Number: 5C3Z-4A376-CA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Dimensions: 25.4 x 6.0 x 15.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2004 Ford Excursion Drive Shaft
Part Number: 3C7Z-4602-BA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Manufacturer Note: Parts List No. 501, 4x2
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C7Z-4602-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2004 Ford Excursion Drive Shaft
Part Number: 3C7Z-4602-AA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Manufacturer Note: Parts List No. 500, 4x4
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C7Z-4602-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2004 Ford Excursion Drive Shaft
Part Number: 2C7Z-4602-HA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C7Z-4602-HA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford Excursion Drive Shaft
Part Number: 2C7Z-4602-GA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C7Z-4602-GA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford Excursion Drive Shaft
Part Number: 2C7Z-4602-FA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C7Z-4602-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 10 Cyl 6.8 L GAS
View related parts
2004 Ford Excursion Drive Shaft
Part Number: 2C7Z-4602-EA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C7Z-4602-EA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 10 Cyl 6.8 L GAS
View related parts
2004 Ford Excursion Drive Shaft
Part Number: 2C7Z-4602-AA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C7Z-4602-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford Excursion Submodels:
- Eddie Bauer, Limited, XLS, XLT | 8 Cyl 5.4 L GAS

2004 Ford Excursion Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2004 Ford Excursion Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2004 Ford Excursion Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2004 Ford Excursion Drive Shaft Parts Questions & Experts Answers

Q: How to Service and Repair the Rear Two-Piece Drive Shaft on 2004 Ford Excursion?
A: A proper service or repair of the rear two-piece driveshaft requires vehicle lifting and axle support before indexing the driveshaft at the axle flange to disconnect it by removing and discarding all bolts, U-joint retainers and mechanics wire support. Mechanics wire should be used for driveshaft support. The driveshaft needs disconnecting from the transfer case or transmission of four-wheel drive vehicles or vehicles with circular flanges while mechanics wire supports the removed bolts. You must mark the transmission output shaft position when dealing with a slip-yoke transmission system. Before continuing detach the bolts which stabilize the center bearing support and take off the driveshaft. Clean all grease deposits together with dirt and rust from driveshaft flange yoke areas and all driveshaft slip yoke surfaces. The examination of the driveshaft slip yoke boot for holes and tears requires replacement when needed while checking the driveshaft center bearing support for rough movement demands its replacement with a new component. Check the center bearing rubber insulator for degradation and unstable condition before making a necessary replacement. Check the transmission together with the transfer case along with the axle seals for damage to replace them when needed. During reinstallation of the driveshaft you must coat the slip yoke spline with grease while following the index marks from removal and using newly installed bolts and retainers with correct bolt direction for vehicle requirements. A reverse order of the removal method completes the installation.