How to service and repair the front brake caliper on 2007 Mercury Mountaineer?

Service or repair operations for front brake calipers should start with positioning the vehicle in neutral gear while it rests on a hoist. The correct brake components need permanent protection which requires only using approved DOT 3 motor vehicle brake fluid. The brake hose flow bolt needs removal while placing the brake hose aside with disposal of two copper washers and fluid port capping. The brake caliper sight hole should never be used for piston retraction because it damages their components. The brake caliper guide pin bolts should first be removed along with the brake caliper. The replacement of a new brake caliper becomes necessary in case either leakage or boot damage exists. The installation process begins with a bottom brake caliper bolt located at the top and requires the guide pin brake caliper bolt to be tightened next before mounting the brake caliper and securing guide pin bolts to 72 Nm (53 ft. lbs.). Position the brake hose with two new copper washers before installing the brake hose flow bolt and tightening it to 35 Nm torque. The brake caliper should be bled before performing a normal operational test of the entire braking system. Brake fluid poses a risk to both painted surfaces and plastic materials so surface wash spills right away with water. In case of emergency brake fluid information consult a doctor or dial 1-800-959-3673 to reach Ford/Motorcraft products either in the USA or Canada.

OEM 2007 Mercury Mountaineer Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Brake Calipers found

View related parts
2007 Mercury Mountaineer Caliper, Rear Passenger Side
Part Number: 6L2Z-2552-A
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Passenger Side
- Replaces: 1L2Z-2552-AA, 1L2Z-2552-BA, 3L2Z-2552-AA, BRCF-181
- Base No.: 2552
- Item Weight: 6.30 Pounds
- Item Dimensions: 6.9 x 3.6 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L2Z-2552-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Mercury Mountaineer Submodels:
- Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
2007 Mercury Mountaineer Caliper, Front Passenger Side
Part Number: 6L2Z-2B120-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front Passenger Side
- Base No.: 2B120
- Item Weight: 16.10 Pounds
- Item Dimensions: 4.7 x 7.5 x 11.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L2Z-2B120-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Mercury Mountaineer Submodels:
- Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
2007 Mercury Mountaineer Caliper, Front Driver Side
Part Number: 6L2Z-2B121-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front Driver Side
- Base No.: 2B120
- Item Weight: 17.10 Pounds
- Item Dimensions: 4.6 x 7.7 x 11.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L2Z-2B121-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Mercury Mountaineer Submodels:
- Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
2007 Mercury Mountaineer Caliper, Rear Driver Side
Part Number: 6L2Z-2553-A
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Driver Side
- Replaces: 1L2Z-2553-AA, 1L2Z-2553-BA, 3L2Z-2553-AA, BRCF-13
- Base No.: 2552
- Item Weight: 5.70 Pounds
- Item Dimensions: 6.8 x 3.6 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L2Z-2553-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Mercury Mountaineer Submodels:
- Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS

2007 Mercury Mountaineer Brake Caliper

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2007 Mercury Mountaineer Brake Caliper available at FordPartsDeal.com. You can confidently purchase our OEM 2007 Mercury Mountaineer Brake Caliper as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2007 Mercury Mountaineer Brake Caliper Parts Questions & Experts Answers

Q: How to service and repair the front brake caliper on 2007 Mercury Mountaineer?
A: Service or repair operations for front brake calipers should start with positioning the vehicle in neutral gear while it rests on a hoist. The correct brake components need permanent protection which requires only using approved DOT 3 motor vehicle brake fluid. The brake hose flow bolt needs removal while placing the brake hose aside with disposal of two copper washers and fluid port capping. The brake caliper sight hole should never be used for piston retraction because it damages their components. The brake caliper guide pin bolts should first be removed along with the brake caliper. The replacement of a new brake caliper becomes necessary in case either leakage or boot damage exists. The installation process begins with a bottom brake caliper bolt located at the top and requires the guide pin brake caliper bolt to be tightened next before mounting the brake caliper and securing guide pin bolts to 72 Nm (53 ft. lbs.). Position the brake hose with two new copper washers before installing the brake hose flow bolt and tightening it to 35 Nm torque. The brake caliper should be bled before performing a normal operational test of the entire braking system. Brake fluid poses a risk to both painted surfaces and plastic materials so surface wash spills right away with water. In case of emergency brake fluid information consult a doctor or dial 1-800-959-3673 to reach Ford/Motorcraft products either in the USA or Canada.