How to Service and Repair a Lower Control Arm on 2008 Ford Crown Victoria?

You need to disable the fire suppression system before starting lower control arm work because it reduces the risk of harm. Put the holding feature on the stud and release the lower ball joint nut before taking out the wheel and tire. First you should take out both the shock absorber lower nut and the flag bolt. Keep the steering bellows boot safe by not removing the cam bolt yet and take off all three lower arm bushing bracket bolts plus the two steering gear-to-crossmember stud nuts. Unlock the steering gear to reach its cam bolt after removing its crossmember studs. Then remove both elements and the lower arm. First position the lower arm and add the cam bolt and nut only lightly. Secure the steering gear by installing its studs with 30 Nm torque (22 lb-ft). Secure the two steering gear-to-crossmember nuts at 103 Nm (76 lb-ft) and also use a torque wrench to tighten the three lower arm bushing bracket bolts to 90 Nm (66 lb-ft). Delay installing the lower cam nuts and shock absorber nuts with the flag bolt to put the lower ball joint nut in place before fastening it to 150 Nm (111 lb-ft). Put back the tire and wheel until the vehicle stands on the components. Then apply 235 Nm (173 lb-ft) torque to the shock absorber lower nut and to the lower arm cam bolt. When installing a fresh lower control arm set the bushing retaining nut to 175 Nm (128 lb-ft). After completing these steps you should inspect the front suspension and recheck the alignment while also restoring power to a fire suppression system according to official safety directions to protect yourself.

OEM 2008 Ford Crown Victoria Control Arm

Suspension Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Control Arms found

View related parts
2008 Ford Crown Victoria Upper Control Arm, Front Driver Side Part Number: 6W1Z-3085-B
$94.37 MSRP: $155.27
You Save: $60.90 (40%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Arm Assembly - Front Suspension; Front Left Upper Control Arm and Ball Joint Assembly.; Control Arm
- Manufacturer Note: L.H., Upper Control Arm only, stamped., FROM 12/05/05
- Position: Front Upper Driver Side
- Replaces: 6W1Z-3085-AA
- Base No.: 3084
- Item Weight: 6.10 Pounds
- Item Dimensions: 4.2 x 11.6 x 13.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W1Z-3085-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Upper Control Arm, Front Passenger Side Part Number: 6W1Z-3084-B
$92.93 MSRP: $152.91
You Save: $59.98 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Assembly - Front Suspension; Front Right Upper Control Arm and Ball Joint Assembly.; Control Arm
- Manufacturer Note: R.H., Upper Control Arm only, stamped., FROM 12/05/05
- Position: Front Upper Passenger Side
- Replaces: 6W1Z-3084-AA
- Base No.: 3084
- Item Weight: 5.50 Pounds
- Item Dimensions: 4.1 x 11.7 x 13.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W1Z-3084-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Lower Control Arm, Front Driver Side Part Number: 6W7Z-3079-B
$200.09 MSRP: $340.00
You Save: $139.91 (42%)
ADD TO CART
Product Specifications
- Other Name: Arm Assembly - Front Suspension; Front Left Lower Control Arm and Ball Joint Assembly.; Control Arm
- Position: Front Lower Driver Side
- Base No.: 3078
- Item Weight: 27.40 Pounds
- Item Dimensions: 4.6 x 15.6 x 26.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W7Z-3079-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Lower Control Arm, Front Passenger Side Part Number: 6W1Z-3078-D
$210.15 MSRP: $341.82
You Save: $131.67 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Assembly - Front Suspension; Front Right Lower Control Arm and Ball Joint Assembly; Control Arm
- Manufacturer Note: R.H., standard suspension, without special packages, FROM 12/05/05
- Position: Front Lower Passenger Side
- Base No.: 3078
- Item Weight: 27.60 Pounds
- Item Dimensions: 5.2 x 15.6 x 26.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W1Z-3078-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Lower Control Arm, Front Passenger Side Part Number: 6W7Z-3078-B
Product Specifications
- Other Name: Arm Assembly - Front Suspension; Front Right Lower Control Arm and Ball Joint Assembly; Control Arm
- Position: Front Lower Passenger Side
- Base No.: 3078
- Item Weight: 26.10 Pounds
- Item Dimensions: 4.7 x 15.7 x 26.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W7Z-3078-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Lower Control Arm, Front Driver Side Part Number: 6W1Z-3079-D
Product Specifications
- Other Name: Arm Assembly - Front Suspension; Front Left Lower Control Arm and Ball Joint Assembly.; Control Arm
- Manufacturer Note: L.H., standard suspension, without special packages, FROM 12/05/05
- Position: Front Lower Driver Side
- Base No.: 3078
- Item Weight: 26.30 Pounds
- Item Dimensions: 6.1 x 15.6 x 25.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W1Z-3079-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS

2008 Ford Crown Victoria Control Arm

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2008 Ford Crown Victoria Control Arm available at FordPartsDeal.com. You can confidently purchase our OEM 2008 Ford Crown Victoria Control Arm as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2008 Ford Crown Victoria Control Arm Parts Q&A

Q: How to Service and Repair a Lower Control Arm on 2008 Ford Crown Victoria?
A: You need to disable the fire suppression system before starting lower control arm work because it reduces the risk of harm. Put the holding feature on the stud and release the lower ball joint nut before taking out the wheel and tire. First you should take out both the shock absorber lower nut and the flag bolt. Keep the steering bellows boot safe by not removing the cam bolt yet and take off all three lower arm bushing bracket bolts plus the two steering gear-to-crossmember stud nuts. Unlock the steering gear to reach its cam bolt after removing its crossmember studs. Then remove both elements and the lower arm. First position the lower arm and add the cam bolt and nut only lightly. Secure the steering gear by installing its studs with 30 Nm torque (22 lb-ft). Secure the two steering gear-to-crossmember nuts at 103 Nm (76 lb-ft) and also use a torque wrench to tighten the three lower arm bushing bracket bolts to 90 Nm (66 lb-ft). Delay installing the lower cam nuts and shock absorber nuts with the flag bolt to put the lower ball joint nut in place before fastening it to 150 Nm (111 lb-ft). Put back the tire and wheel until the vehicle stands on the components. Then apply 235 Nm (173 lb-ft) torque to the shock absorber lower nut and to the lower arm cam bolt. When installing a fresh lower control arm set the bushing retaining nut to 175 Nm (128 lb-ft). After completing these steps you should inspect the front suspension and recheck the alignment while also restoring power to a fire suppression system according to official safety directions to protect yourself.

Related 2008 Ford Crown Victoria Parts

Alternate Year Models

2007 Ford Crown Victoria Control Arm 2009 Ford Crown Victoria Control Arm

OEM 2008 Ford Crown Victoria Control Arm

6 Control Arms found

2008 Ford Crown Victoria Upper Control Arm, Front Driver Side Part Number: 6W1Z-3085-B

2008 Ford Crown Victoria Upper Control Arm, Front Passenger Side Part Number: 6W1Z-3084-B

2008 Ford Crown Victoria Lower Control Arm, Front Driver Side Part Number: 6W7Z-3079-B

2008 Ford Crown Victoria Lower Control Arm, Front Passenger Side Part Number: 6W1Z-3078-D

2008 Ford Crown Victoria Lower Control Arm, Front Passenger Side Part Number: 6W7Z-3078-B

2008 Ford Crown Victoria Lower Control Arm, Front Driver Side Part Number: 6W1Z-3079-D

2008 Ford Crown Victoria Control Arm

2008 Ford Crown Victoria Control Arm Parts Q&A

Related 2008 Ford Crown Victoria Parts

Alternate Year Models