How to Remove and Replace the Front Coil Springs and Shock Absorber Assembly on 2008 Ford Crown Victoria?

The first step to change the front shock absorber along with its spring assembly begins with depowering the fire suppression system to avoid severe personal injuries. Keep the shock absorber center nut in place since discarding three upper mount shock absorber nuts separately helps prevent spring tension from harming the technician. First support the brake hose through the use of mechanic's wire while carefully removing the caliper and pads and anchor plate assembly and its bolts. Start by removing the brake disc before discarding the stabilizer bar upper link nut and the stabilizer bar link lower nut by utilizing the hex holding feature to stop spinning of the stud. The installation requires the wheel speed sensor wiring harness retainer to be detached from the wheel knuckle before discarding the upper ball joint nut and shock absorber lower nut with the flag bolt. The assembly of shock absorber and spring must be removed. The assembly of new shock absorber and springs should start with flag bolt nut and lower nut placement followed by upper ball joint nut tightening at 150 Nm (111 lb-ft). The procedure involves reconnecting the wheel speed sensor wires before inserting the stabilizer link while torquing the lower stabilizer nut to 55 Nm (41 lb-ft) and the upper link to 63 Nm (46 lb-ft). Place the brake disc followed by the brake caliper and anchor plate assembly and fasten it with two anchor plate bolts tightened to 160 Nm (118 lb-ft). The technician should put back the wheel and tire then fasten the shock absorber upper mount nuts to 30 Nm (22 lb-ft). When the vehicle rests on its wheel and tire assembly tighten the shock absorber lower nut to 235 Nm (173 lb-ft). All safety procedures must be strictly followed before enabling the engine of cars with fire suppression systems to prevent serious personal injury.

OEM 2008 Ford Crown Victoria Coil Springs

Strut Spring

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Coil Springs found

View related parts
2008 Ford Crown Victoria Coil Spring, Yellow, Rear
Part Number: 3W7Z-5560-CA
$80.61 MSRP: $111.52
You Save: $30.91 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Position: Rear
- Replaces: F4AZ-5560-A, F8AZ-5560-DA
- Base No.: 5560
- Item Weight: 8.10 Pounds
- Item Dimensions: 6.0 x 5.9 x 16.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 3W7Z-5560-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Coil Spring, Yellow, Front
Part Number: 9W7Z-5310-B
$62.33 MSRP: $86.23
You Save: $23.90 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Spring Kit Front; Coil Spring Set; Coil Springs; Spring
- Position: Front
- Replaces: 3W1Z-5310-HA
- Base No.: 5310
- Item Weight: 11.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9W7Z-5310-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Coil Spring, Green, Front
Part Number: 9W7Z-5310-C
$111.47 MSRP: $162.25
You Save: $50.78 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Spring Kit Front; Coil Spring Set; Coil Springs; Spring
- Position: Front
- Replaces: 3W1Z-5310-EA, 3W1Z-5310-DA
- Base No.: 5310
- Item Weight: 2.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9W7Z-5310-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Coil Spring, White, Front
Part Number: 3W1Z-5310-BA
$78.64 MSRP: $108.79
You Save: $30.15 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Spring Kit Front; Coil Spring Set; Coil Springs; Spring
- Position: Front
- Base No.: 5310
- Item Weight: 10.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 3W1Z-5310-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Coil Spring, Black, Front
Part Number: 3W7Z-5310-AA
$51.56 MSRP: $70.16
You Save: $18.60 (27%)
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Spring Kit Front; Coil Spring Set; Coil Springs
- Position: Front
- Base No.: 5310
- Item Weight: 9.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 3W7Z-5310-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Coil Spring, Purple, Rear
Part Number: 6W7Z-5560-B
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Position: Rear
- Base No.: 5560
- Item Weight: 10.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 6W7Z-5560-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Coil Spring, Blue/Green, Front
Part Number: 9W7Z-5310-A
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Replaces: 6W7Z-5310-A
- Base No.: 5310
- Item Weight: 10.20 Pounds
- Item Dimensions: 5.4 x 5.4 x 15.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9W7Z-5310-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Coil Spring, Pink, Rear
Part Number: 6W7Z-5560-C
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Position: Rear
- Replaces: 5W7Z-5560-AA
- Base No.: 5560
- Item Weight: 10.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 6W7Z-5560-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Coil Spring, Red, Front
Part Number: 3W7Z-5310-DA
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs
- Position: Front
- Base No.: 5310
- Item Weight: 9.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 3W7Z-5310-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Crown Victoria Coil Spring, Dark Green, Rear
Part Number: 6W7Z-5560-A
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Position: Rear
- Replaces: 3W7Z-5560-DA, F8AZ-5560-FA
- Base No.: 5560
- Item Weight: 8.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 6W7Z-5560-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Crown Victoria Submodels:
- Base, Fleet, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS

2008 Ford Crown Victoria Coil Springs

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2008 Ford Crown Victoria Coil Springs available at FordPartsDeal.com. You can confidently purchase our OEM 2008 Ford Crown Victoria Coil Springs as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2008 Ford Crown Victoria Coil Springs Parts Questions & Experts Answers

Q: How to Remove and Replace the Front Coil Springs and Shock Absorber Assembly on 2008 Ford Crown Victoria?
A: The first step to change the front shock absorber along with its spring assembly begins with depowering the fire suppression system to avoid severe personal injuries. Keep the shock absorber center nut in place since discarding three upper mount shock absorber nuts separately helps prevent spring tension from harming the technician. First support the brake hose through the use of mechanic's wire while carefully removing the caliper and pads and anchor plate assembly and its bolts. Start by removing the brake disc before discarding the stabilizer bar upper link nut and the stabilizer bar link lower nut by utilizing the hex holding feature to stop spinning of the stud. The installation requires the wheel speed sensor wiring harness retainer to be detached from the wheel knuckle before discarding the upper ball joint nut and shock absorber lower nut with the flag bolt. The assembly of shock absorber and spring must be removed. The assembly of new shock absorber and springs should start with flag bolt nut and lower nut placement followed by upper ball joint nut tightening at 150 Nm (111 lb-ft). The procedure involves reconnecting the wheel speed sensor wires before inserting the stabilizer link while torquing the lower stabilizer nut to 55 Nm (41 lb-ft) and the upper link to 63 Nm (46 lb-ft). Place the brake disc followed by the brake caliper and anchor plate assembly and fasten it with two anchor plate bolts tightened to 160 Nm (118 lb-ft). The technician should put back the wheel and tire then fasten the shock absorber upper mount nuts to 30 Nm (22 lb-ft). When the vehicle rests on its wheel and tire assembly tighten the shock absorber lower nut to 235 Nm (173 lb-ft). All safety procedures must be strictly followed before enabling the engine of cars with fire suppression systems to prevent serious personal injury.