How to remove and replace the RH temperature blend door actuator on 2008 Ford Escape?

In order to install the RH temperature blend door actuator, undo the upper center instrument panel finish panel and passenger airbag module. Open and loosen screws, take off wire harness holding screws and loosen the actuator. Do not place screws in the plenum. Take the steps in reverse order and screw tighten to 3 Nm to install the new actuator.

OEM 2008 Ford Escape Blend Door Actuator

Air Blend Door Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Blend Door Actuators found

View related parts
2008 Ford Escape Vacuum Motor Part Number: AR3Z-19E616-D
$24.37 MSRP: $39.31
You Save: $14.94 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor Assembly; HVAC Air Adjustment Control Motor; Inlet Door Actuator; Heater Blend Door Actuator.; Adjust Motor; Mode Motor; Motor
- Replaces: 8L8Z-19E616-D, 9L3Z-19E616-C, 8L8Z-19E616-A
- Base No.: 19E616A
- Item Weight: 0.50 Pounds
- Item Dimensions: 6.2 x 4.1 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: AR3Z-19E616-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Escape Submodels:
- Hybrid, Limited, Limited Hybrid, XLS, XLT | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2008 Ford Escape Door Actuator Part Number: AL8Z-19E616-F
$26.67 MSRP: $43.02
You Save: $16.35 (39%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Motor Assembly; HVAC Air Adjustment Control Motor; HVAC Blend Door Actuator; HVAC Heater Blend Door Actuator; Vacuum Motor; Mode Motor; Motor
- Replaces: 8L8Z-19E616-B, 4L3Z-19E616-EA, 8L8Z-19E616-F, 8L8Z-19E616-E, YH-1750
- Base No.: 19E616A
- Item Weight: 0.50 Pounds
- Item Dimensions: 8.5 x 7.6 x 7.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: AL8Z-19E616-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Escape Submodels:
- Hybrid, Limited, Limited Hybrid, XLS, XLT | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2008 Ford Escape Door Actuator, Front Part Number: 8L8Z-19E616-C
$35.06 MSRP: $56.56
You Save: $21.50 (39%)
ADD TO CART
Product Specifications
- Other Name: Motor Assembly; Drive Motor Battery Pack Cooling Fan Duct Actuator Door Motor; HVAC Actuators; Vacuum Motor; Adjust Motor; Mode Motor; Motor
- Position: Front
- Replaces: 7L1Z-19E616-F
- Base No.: 19E616
- Item Weight: 0.50 Pounds
- Item Dimensions: 6.2 x 4.1 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L8Z-19E616-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Escape Submodels:
- Hybrid, Limited, Limited Hybrid, XLS, XLT | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

2008 Ford Escape Blend Door Actuator

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2008 Ford Escape Blend Door Actuator available at FordPartsDeal.com. You can confidently purchase our OEM 2008 Ford Escape Blend Door Actuator as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2008 Ford Escape Blend Door Actuator Parts Q&A

Q: How to remove and replace the RH temperature blend door actuator on 2008 Ford Escape?
A: In order to install the RH temperature blend door actuator, undo the upper center instrument panel finish panel and passenger airbag module. Open and loosen screws, take off wire harness holding screws and loosen the actuator. Do not place screws in the plenum. Take the steps in reverse order and screw tighten to 3 Nm to install the new actuator.