How to Service and Repair the Clock Spring Assembly on Ford Edge?

Service and repair procedures for the Clock Spring assembly start with removing the driver air bag module. The customer must inspect the SRS before vehicle handover through an ON fuse check of the proper Restraints Control Module (RCM). The rotor of the Clock Spring assembly should remain fixed at zero steering angle after steering wheel removal when working on vehicles that incorporate steering angle sensors with adaptive headlamps to protect system components from damage or failure. Before taking off the steering wheel it is crucial to verify that road wheels face forward. You should tape the Clock Spring rotor at the steering column shaft to keep it in position before releasing the two tabs that allow you to position the upper steering column shroud upward while taking out the lower steering column shroud's three screws. Detach the Clock Spring electrical connector before taking off the tape from the Clock Spring rotor while maintaining its central location. To perform the removal, eliminate the 2 screws which allows extraction of the Clock Spring. Reinstall a used Clock Spring only when it sits properly in the center position to stop premature damage from occurring. Keep the Clock Spring outer housing fixed in place while rotating the rotor opposite the direction of the clock until you meet resistance and turn it another 2.25turns clockwise until the wires align with the 12 o'clock position. Position the steering angle sensor ring arrow with the housing arrow. During Clock Spring installation when no one is caring for it, the centralizing process must be performed again. After ensuring complete insertion of the Clock Spring into the multifunction switch housing hook up its electrical connector. Apply the centralizing procedure once again for the Clock Spring if the technician departed the vehicle without supervision before moving forward with attaching the steering shrouds and upper cover. The next installation step involves attaching the steering wheel while removing the Clock Spring sealing key only when you installed a new Clock Spring before securing the driver air bag module.

OEM Ford Edge Clock Spring

Spiral Cable Clock Spring

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Clock Springs found

View related parts
Ford Edge Clockspring
Part Number: GB5Z-14A664-C
$237.12 MSRP: $348.20
You Save: $111.08 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaces: CT4Z-14A664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | Limited, SE, SEL, Sport | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Ford Edge Clockspring
Part Number: BE5Z-14A664-A
$85.65 MSRP: $124.67
You Save: $39.02 (32%)
ADD TO CART
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaces: 6E5Z-14A664-B, 8E5Z-14A664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Edge | Limited, SE, SEL, SEL Plus | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Clockspring
Part Number: GB5Z-14A664-D
$185.67 MSRP: $270.27
You Save: $84.60 (32%)
ADD TO CART
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaces: BA1Z-14A664-A, CA1Z-14A664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2014 Ford Edge | Limited, SE, SEL, Sport | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Ford Edge Clockspring
Part Number: FT4Z-14A664-D
$180.42 MSRP: $262.62
You Save: $82.20 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaces: FT4Z-14A664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | SE, SEL, Sport, ST, ST-Line, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Edge Clockspring
Part Number: BA1Z-14A664-A
$185.67 MSRP: $270.27
You Save: $84.60 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover And Contact Plate; Air Bag Clockspring; Cover And Contact Plate Assembly
- Manufacturer Note: BLACK
- Replaced by: GB5Z-14A664-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011 Ford Edge | Limited, SE, SEL, Sport | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Ford Edge Clockspring
Part Number: EG9Z-14A664-J
$190.32 MSRP: $277.03
You Save: $86.71 (32%)
ADD TO CART
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaced by: EG9Z-14A664-M
- Replaces: EG9Z-14A664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | SE, SEL, Sport, ST, ST-Line, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Edge Clockspring
Part Number: EG9Z-14A664-H
$144.64 MSRP: $267.00
You Save: $122.36 (46%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaced by: EG9Z-14A664-N
- Replaces: DG9Z-14A664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023, 2015 Ford Edge | SE, SEL, Sport, ST, ST-Line, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Edge Clockspring
Part Number: G2GZ-14A664-D
$869.67 MSRP: $1288.40
You Save: $418.73 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaced by: K2GZ-14A664-B
- Replaces: G2GZ-14A664-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2021 Ford Edge | SE, SEL, Sport, ST, ST-Line, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Edge Clockspring
Part Number: K2GZ-14A664-A
$940.67 MSRP: $1393.58
You Save: $452.91 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaces: G2GZ-14A664-A, G2GZ-14A664-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2024 Ford Edge | SE, SEL, Sport, ST, ST-Line, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Edge Clockspring
Part Number: F2GZ-14A664-B
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaces: F2GZ-14A664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2016 Ford Edge | SE, SEL, Sport, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Edge Clockspring
Part Number: AT4Z-14A664-A
$140.03 MSRP: $203.83
You Save: $63.80 (32%)
Product Specifications
- Other Name: Cover And Contact Plate Assembly; Air Bag Clockspring
- Replaces: 8T4Z-14A664-A, 7T4Z-14A664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Edge | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS

Ford Edge Clock Spring

Welcome to our website where you can discover high-quality, genuine Ford Edge Clock Spring. We offer an extensive inventory of OEM Ford Edge Clock Spring at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Ford Edge Clock Spring Parts Questions & Experts Answers

Clockspring
AT4Z-14A664-A
Q: How to Service and Repair the Clock Spring Assembly on Ford Edge?
A: Service and repair procedures for the Clock Spring assembly start with removing the driver Air Bag module. The customer must inspect the SRS before vehicle handover through an ON fuse check of the proper Restraints Control Module (RCM). The rotor of the Clock Spring assembly should remain fixed at zero steering angle after Steering Wheel removal when working on vehicles that incorporate Steering Angle Sensors with adaptive headlamps to protect system components from damage or failure. Before taking off the steering wheel it is crucial to verify that road wheels face forward. You should tape the Clock Spring rotor at the steering column shaft to keep it in position before releasing the two tabs that allow you to position the upper steering column shroud upward while taking out the lower steering column shroud's three screws. Detach the Clock Spring electrical connector before taking off the tape from the Clock Spring rotor while maintaining its central location. To perform the removal, eliminate the 2 screws which allows extraction of the Clock Spring. Reinstall a used Clock Spring only when it sits properly in the center position to stop premature damage from occurring. Keep the Clock Spring outer housing fixed in place while rotating the rotor opposite the direction of the clock until you meet resistance and turn it another 2.25turns clockwise until the wires align with the 12 o'clock position. Position the steering angle sensor ring arrow with the housing arrow. During Clock Spring installation when no one is caring for it, the centralizing process must be performed again. After ensuring complete insertion of the Clock Spring into the multifunction switch housing hook up its electrical connector. Apply the centralizing procedure once again for the Clock Spring if the technician departed the vehicle without supervision before moving forward with attaching the steering shrouds and upper cover. The next installation step involves attaching the steering wheel while removing the Clock Spring sealing key only when you installed a new Clock Spring before securing the driver air bag module.