What Steps Should Be Taken Before Removing and Installing the Front Coil Springs and Shock Absorber Assembly on Ford Expedition?

Turn off the air suspension switch found in the LH rear quarter trim panel before shock absorber and spring assembly removal or installation to avoid air springs from unexpectedly inflating or deflating since this could lead to vehicle shifting and personal injury. The correct performance of essential systems depends on suspension fasteners so replacement requires you to use new parts of the same design number while following torque specifications during reassembly to guarantee proper fastener retention. Begin the process by setting the vehicle transmission in neutral mode on a hoist setup. Thread the new upper nuts of the shock and spring assembly before tightening them to 35 Nm (26 ft. lbs.). The procedure involves replacing both shock absorber lower nut and bolt components by discarding the initial nut while tightening the new ones to 400 Nm (295 ft. lbs.) after installation. Service the shock absorber and spring assembly only when single components will receive maintenance; otherwise move forward to the subsequent step. A proper spring compressor allows the spring to relax before extracting the shock absorber by removing the nut and washer from the shock rod. Replace this nut with the new one with a tightness of 30 Nm (22 ft. lbs.). After removing the upper mount and dust boot with the insulator, finish the installation process by performing the opposite steps of removal.

How to Service and Repair Front Coil Springs on Ford Expedition?

Service and repair of front coil springs begins with turning off air suspension electrical power by using the air suspension switch to avoid unexpected movement of air springs. See to it that the vehicle rests at an adequate height before you detach the wheel assembly from its tires by avoiding any heat application to avoid both wheel damage and bearing damage. Your first step should be to remove the brake disc shield followed by the upper shock absorber nut and washer together with the front shock absorber through its nuts. After separating the brake hose bracket from the front suspension lower arm and the front stabilizer bar link nut must be detached. A Coil Spring Compressor should compress the front coil spring before eliminating the lower ball joint castle nut by removing the cotter pin. First detach the lower ball joint from the front wheel spindle by using a Pitman Arm Puller then set the spindle to the side before taking out the front coil spring. When installing the front coil spring insert it into the front suspension lower arm while it spans across the first hole and reaches the second one. Fasten the lower ball joint castle nut by adding a new cotter pin before tightening the front stabilizer bar link nut. After removing the Coil Spring Compressor you should install the front shock absorber starting with the shock absorber lower nuts before proceeding to install the upper shock absorber nut and washer. Hour all operations by carefully installing the brake hose bracket screw and the brake disc shield. Endeavor to clean the wheel hub mounting surface because improper metal-to-metal contact leads to wheel nut loosening which threatens driving control. To complete the procedure activate the air suspension feature by turning on the corresponding switch before installing the tire and wheel unit along with performing necessary front end alignment checks.

OEM Ford Expedition Coil Springs

Strut Spring

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

32 Coil Springs found

View related parts
Ford Expedition Coil Spring, Rear Part Number: AL1Z-5560-E
$129.73 MSRP: $188.83
You Save: $59.10 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Coil; Coil Spring, Rear; Coil Springs; Spring
- Position: Rear
- Replaces: AL1Z-5560-A, AL1Z-5560-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2017 Ford Expedition | Eddie Bauer, EL King Ranch, EL Limited, EL Platinum, EL SSV, EL XL, EL XLT, King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX
View related parts
Ford Expedition Coil Spring, Rear Part Number: F75Z-5560-DA
$125.84 MSRP: $174.08
You Save: $48.24 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Coil; Coil Spring, Rear; Coil Spring Kit Rear; Coil Spring Set; Coil Springs; Spring
- Manufacturer Note: Spring code 5, 4x4
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2002 Ford Expedition | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Rear Part Number: F75Z-5560-FA
$77.58 MSRP: $107.32
You Save: $29.74 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Coil; Coil Spring, Rear; Coil Spring Kit Rear Cargo; Coil Spring Set; Coil Springs; Spring
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Ford Expedition | Eddie Bauer, XLT | 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Front Part Number: 9L1Z-5310-P
$136.03 MSRP: $198.00
You Save: $61.97 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Replaces: 9L1Z-5310-J, 7L7Z-5310-J
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2017 Ford Expedition | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL Platinum, EL XL, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Rear Part Number: AL1Z-5560-F
$146.10 MSRP: $212.67
You Save: $66.57 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Coil; Coil Spring, Rear; Coil Springs; Spring
- Position: Rear
- Replaces: AL1Z-5560-B, AL1Z-5560-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2017 Ford Expedition | EL Eddie Bauer, EL King Ranch, EL Limited, EL Platinum, EL SSV, EL XL, EL XLT, King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX
View related parts
Ford Expedition Coil Spring, Front Part Number: JL1Z-5310-D
$121.42 MSRP: $176.73
You Save: $55.31 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2024 Ford Expedition | Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XL, Max XLT | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Coil Spring, Front Part Number: JL1Z-5310-W
$142.32 MSRP: $207.17
You Save: $64.85 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022-2024 Ford Expedition | King Ranch, Limited, Platinum, SSV, Timberline, XL, XL STX, XLT | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Air Spring, Rear Part Number: 7L1Z-5A891-B
Product Specifications
- Other Name: Spring; Air Suspension Spring, Rear; Coil Spring, Rear; Air Suspension Spring Set; Air Suspension Spring
- Position: Rear
- Replaces: 7L1Z-5A891-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Expedition | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, XLT | 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Rear Part Number: F75Z-5560-CA
Product Specifications
- Other Name: Spring - Coil; Coil Spring, Rear; Coil Spring Kit Rear Cargo; Coil Spring Set; Coil Springs; Spring
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Ford Expedition | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS
View related parts
Ford Expedition Air Spring Part Number: 4L1Z-5A891-AA
Product Specifications
- Other Name: Spring; Air Suspension Spring Set; Air Suspension Spring
- Replaced by: 6L1Z-5A891-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2006 Ford Expedition | Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Front Part Number: 3L3Z-5310-XA
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Spring Kit Front; Coil Spring Set; Coil Springs; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2002 Ford Expedition | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Red, Front Part Number: 3L1Z-5310-AA
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2006 Ford Expedition | Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Blue, Front Part Number: 3L1Z-5310-BA
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2006 Ford Expedition | Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Front Part Number: 3L3Z-5310-YA
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Spring Kit Front; Coil Spring Set; Coil Springs; Spring
- Position: Front
- Replaces: F75Z-5310-LA, F65Z-5310-PA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Expedition | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring Part Number: 3U2Z-5580-KA
Product Specifications
- Other Name: Spring; Air Suspension Spring; Air Suspension Spring Set; Coil Springs; Air Spring; Spring Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2002 Ford Expedition | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring Part Number: 3U2Z-5580-LA
Product Specifications
- Other Name: Spring; Air Suspension Spring; Air Suspension Spring Set; Coil Springs; Air Spring; Spring Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2002 Ford Expedition | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Front Part Number: 7L1Z-5310-A
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Expedition | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, XLT | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Front Part Number: 9L1Z-5310-N
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Replaces: 7L1Z-5310-EB, 9L1Z-5310-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2014 Ford Expedition | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL XL, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, XLT | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Coil Spring, Rear Part Number: 9L1Z-5560-B
Product Specifications
- Other Name: Spring - Coil; Coil Spring, Rear; Coil Springs; Spring
- Position: Rear
- Replaces: 7L1Z-5560-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Expedition | EL Eddie Bauer, EL King Ranch, EL Limited, EL XLT | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Air Spring, Rear Part Number: 8L1Z-5A891-B
Product Specifications
- Other Name: Spring; Air Suspension Spring, Rear; Air Suspension Spring Set; Air Suspension Spring
- Position: Rear
- Replaces: 8L1Z-5A891-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2014 Ford Expedition | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL XL, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, XL, XLT | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS

| Page 1 of 2 |Next >

1-20 of 32 Results

Ford Expedition Coil Springs

OEM Coil Springs boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Coil Springs with long life and a perfect fit. Come to our website and find genuine Ford Expedition parts. We keep a wide inventory of OEM Expedition parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Coil Springs in the Ford Expedition vehicles serve a very important function of bearing the weight of the car and cushioning the car bottom on bad roads. Some of the signs of worn or bad coil springs are, the car is sagging or bottoming out and uneven tire wear. New shock absorber springs can help you return your ride height and smoothness, with OEM, progressive, or cargo specific springs for additional weight. Coil springs are available in different sizes of height and rate, that relates to handling and traction. Just like the name suggests, there are linear rate springs, progressive springs and the dual rate springs which provide different rates of stiffness for the optimal performance. Normally on adjustable damping coilovers it possible to change the height of the car and maintain the same lowering kit without the need to change.

Ford Expedition Coil Springs Parts and Q&A

Coil Spring, Red, Front
3L1Z-5310-AA
Q: What Steps Should Be Taken Before Removing and Installing the Front Coil Springs and Shock Absorber Assembly on Ford Expedition?
A:
Turn off the Air Suspension switch found in the LH rear quarter trim panel before Shock Absorber and spring assembly removal or installation to avoid air springs from unexpectedly inflating or deflating since this could lead to vehicle shifting and personal injury. The correct performance of essential systems depends on suspension fasteners so replacement requires you to use new parts of the same design number while following torque specifications during reassembly to guarantee proper fastener retention. Begin the process by setting the vehicle transmission in neutral mode on a hoist setup. Thread the new upper nuts of the shock and spring assembly before tightening them to 35 Nm (26 ft. lbs.). The procedure involves replacing both shock absorber lower nut and bolt components by discarding the initial nut while tightening the new ones to 400 Nm (295 ft. lbs.) after installation. Service the shock absorber and spring assembly only when single components will receive maintenance; otherwise move forward to the subsequent step. A proper spring compressor allows the spring to relax before extracting the shock absorber by removing the nut and washer from the shock rod. Replace this nut with the new one with a tightness of 30 Nm (22 ft. lbs.). After removing the upper mount and dust boot with the insulator, finish the installation process by performing the opposite steps of removal.
Coil Spring, Front
3L1Z-5310-CA
Q: How to Service and Repair Front Coil Springs on Ford Expedition?
A:
Service and repair of front coil springs begins with turning off air suspension electrical power by using the air suspension switch to avoid unexpected movement of air springs. See to it that the vehicle rests at an adequate height before you detach the wheel assembly from its tires by avoiding any heat application to avoid both wheel damage and bearing damage. Your first step should be to remove the brake disc shield followed by the upper Shock Absorber nut and washer together with the front shock absorber through its nuts. After separating the brake hose bracket from the front suspension lower arm and the front stabilizer bar link nut must be detached. A Coil Spring Compressor should compress the front coil spring before eliminating the lower ball joint castle nut by removing the cotter pin. First detach the lower ball joint from the front wheel Spindle by using a Pitman Arm Puller then set the spindle to the side before taking out the front coil spring. When installing the front coil spring insert it into the front suspension lower arm while it spans across the first hole and reaches the second one. Fasten the lower ball joint castle nut by adding a new cotter pin before tightening the front stabilizer bar link nut. After removing the Coil Spring Compressor you should install the front shock absorber starting with the shock absorber lower nuts before proceeding to install the upper shock absorber nut and washer. Hour all operations by carefully installing the brake hose bracket screw and the brake disc shield. Endeavor to clean the wheel hub mounting surface because improper metal-to-metal contact leads to wheel nut loosening which threatens driving control. To complete the procedure activate the air suspension feature by turning on the corresponding switch before installing the tire and wheel unit along with performing necessary front end alignment checks.