How to service and repair front brake pads on Ford Explorer?

The front brake pad service starts with drawing brake fluid from the master cylinder reservoir until it reaches half level. Begin by raising and supporting the vehicle before taking out both wheel and tire assembly. You must install fresh pads only if their top metal backing plate exceeds the defined thickness limit or shows wear damage while also requiring installation of new pads in complete axle sets. Check the pads for damage or contamination before untightening the lower bolt of the right caliper and the upper bolt of the left caliper. Remove the brake disc rotor pads and stainless slippers after rotating the disc brake caliper to an opposite position from the rotor. Any detected cracks on the brake disc will require installation of a new brake disc. Machine the brake disc when braking causes vibrations to appear in the steering wheel and seat or brake pedal. The machining process becomes necessary for heavily scored brake discs similar to those from lining wear that reaches the backing plate. The brake disc minimum thickness requirement should also be measured during this operation. Failure to meet brake disc specifications directs the technicians to install a new brake disc as replacement. The disc brake caliper requires dismantling due to the presence of leaks during inspection. Installation requires a suitable suction device to extract brake fluid from the master cylinder then cleaning occurs on support bracket and slipper surfaces before installation. The installation process requires installing slippers and pads according to piston compression rules with C-clamp and wooden block usage along with potential master cylinder fluid reduction. After placing the disc brake caliper inside the anchor bracket, install the caliper bolt and replace the wheel along with its attached tire. A complete brake system inspection must conclude with a functional system check.

How to service the rear brake pads on Ford Explorer?

When servicing the rear brake pads one should use brake fluid that meets manufacturer requirements but avoid using any remaining fluid as it may cause damage by introducing contaminants. The proper braking performance requires new brake pads or shoes on both sides of an axle to avoid uneven stopping power. You should inspect the brake fluid in the master cylinder reservoir then drain it until it reaches half-way up the tank if needed. Proceed to eliminate the wheel in addition to the tire. Pry tools must avoid entering the sight hole since doing so will damage caliper pistons and any attempt to let the brake caliper hang from the hose can result in hose damage. Support the caliper with mechanic's wire after uninstalling the two brake caliper guide pin bolts from their positions. Users should inspect the brake pads for signs of wear while checking the brake disc for any need in machining or replacing. Discard the brake pad clips followed by removing the two brake pads. It is important to know that a single brake disc pad kit contains linings that cover both sides of the pad installation. After installing brake pad clips together with the brake pads maintain the piston and boots safe by using a worn brake pad to push the caliper piston into the caliper bores through the suitable tool. Equip the brake caliper and add the two brake caliper guide pin bolts while tightening them to 32 Nm (24 lb-ft). Begin by adding clean specified brake fluid into the brake master cylinder reservoir before replacing the wheel along with the tire. Several brake operations should be applied to check that braking functions properly.

OEM Ford Explorer Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

21 Brake Pads found

View related parts
Ford Explorer Brake Pads, Front Part Number: DG1Z-2001-F
$162.44 MSRP: $245.00
You Save: $82.56 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Disc Brake Pad Set; Front Pads
- Position: Front
- Replaces: BRF-17, DG1Z-2001-E, DG1Z-2001-B, BRF-1435
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Explorer | Base, Limited, Platinum, Sport, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Explorer Brake Pads, Rear Part Number: FB5Z-2200-C
$72.78 MSRP: $112.00
You Save: $39.22 (36%)
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Disc Brake Pad Set
- Position: Rear
- Replaced by: FB5Z-2200-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2019 Ford Explorer | Base, Limited, Platinum, Sport, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Explorer Brake Pads, Rear Part Number: DG1Z-2200-B
$78.95 MSRP: $121.50
You Save: $42.55 (36%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Kit - Brake Lining; Disc Brake Pad Set
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Explorer | Base, Limited, Platinum, Sport, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Explorer Brake Pads, Front Part Number: 2U2Z-2V001-YA
$44.51 MSRP: $66.65
You Save: $22.14 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads; Pad
- Manufacturer Note: Ford Retail Spec
- Position: Front
- Replaces: 1L2Z-2001-BA, 2L2Z-2001-BA, 1L2Z-2001-AA, BRF-833-B, 7L2Z-2001-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Ford Explorer | Eddie Bauer, Limited, NBX, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Brake Pads, Front Part Number: L1MZ-2001-F
$100.65 MSRP: $146.50
You Save: $45.85 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: BRF-1882, L1MZ-2001-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Explorer | Base, King Ranch, Limited, Limited Hybrid, Platinum, Platinum Hybrid, ST, ST-Line, Timberline, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Explorer Brake Pads Part Number: XU2Z-2V200-SA
$41.33 MSRP: $56.24
You Save: $14.91 (27%)
ADD TO CART
Product Specifications
- Other Name: Pad; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Disc Brake Pad Set
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-2001 Ford Explorer | Eddie Bauer, Expedition, Limited, Postal, Sport, XL, XL Fleet, XLS, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Explorer Brake Pads, Front Part Number: 1U2Z-2V001-TA
$44.51 MSRP: $66.65
You Save: $22.14 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad; Disc Brake Pad Set, Front; Front Pads
- Manufacturer Note: excludes electric
- Position: Front
- Replaces: BRF-652, XU2Z-2V001-ARA, 1L2Z-2001-CA, XL2Z-2B121-BA, 2L5Z-2001-AA, XL2Z-2B120-BA, XL2Z-2001-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1998 Ford Explorer | Eddie Bauer, Expedition, Limited, Sport, XL, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Explorer Brake Pads, Front Part Number: GB5Z-2001-B
$94.12 MSRP: $137.00
You Save: $42.88 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: DG1Z-2001-A, GB5Z-2001-A, BRF-1527, BRF-16, DG1Z-2001-D, BRF-41
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Explorer | Base, Limited, Platinum, Sport, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Explorer Brake Pads, Front Part Number: 8L2Z-2V001-B
$45.79 MSRP: $66.65
You Save: $20.86 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: BR-1158-B, 6L2Z-2001-A, 8L2Z-2V001-A, BRF-1158
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Ford Explorer | Eddie Bauer, Limited, XLS, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Brake Pads, Rear Part Number: L1MZ-2200-F
$78.66 MSRP: $114.50
You Save: $35.84 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Rear; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Explorer | Base, King Ranch, Limited, Limited Hybrid, Platinum, Platinum Hybrid, ST, ST-Line, Timberline, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Explorer Brake Pads, Rear Part Number: 8L2Z-2V200-B
$45.79 MSRP: $66.65
You Save: $20.86 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Rear Pads
- Position: Rear
- Replaces: 7L2Z-2200-A, 8L2Z-2V200-A, 8L2Z-2200-AB, 1L2Z-2200-AA, BRF-1109, 3L2Z-2200-BA, BRF-881, BR-1109-B, 6L2Z-2200-B, 8L2Z-2200-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2010 Ford Explorer | Eddie Bauer, Limited, NBX, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Brake Pads, Front Part Number: EB5Z-2001-B
$72.78 MSRP: $112.00
You Save: $39.22 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: AG1Z-2001-C, BRF-1070-B, BRF-1376-A, EB5Z-2001-A, AG1Z-2001-A, BRF-1467, BRF-1385, BB5Z-2001-A, BB5Z-2001-B, BRF-6, BRF-1376, AG1Z-2001-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2019 Ford Explorer | Base, Limited, Platinum, Sport, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Explorer Brake Pads, Front Part Number: BU2Z-2V001-C
$46.59 MSRP: $66.65
You Save: $20.06 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: BL5Z-2001-A, BRF-1479, BU2Z-2V001-B, 1L5Z-2001-BB, 3L2Z-2001-AA, 4L5Z-2001-AA, 4L2Z-2001-BA, 3L5Z-2001-AA, 6L5Z-2001-A, BRF-1399, BRF-1394, BR-833-B, 6L5Z-2001-B, BRF-833
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Explorer | Eddie Bauer, Limited, Postal, XL Fleet, XLS, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Explorer Brake Pads Part Number: XL2Z-2001-AA
$6.33 MSRP: $8.75
You Save: $2.42 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Shoe; Disc Brake Pad Set; Front Pads
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2001 Ford Explorer | Eddie Bauer, Limited, Postal, Sport, XL, XL Fleet, XLS, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Explorer Brake Pads, Rear Part Number: FG1Z-2200-B
$79.46 MSRP: $115.67
You Save: $36.21 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Rear Pads
- Position: Rear
- Replaces: BRF-1384, BRF-1477, EG1Z-2200-C, FG1Z-2200-A, BRF-1539, BRF-1447, DG1Z-2200-C, EG1Z-2200-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Explorer | Base, Limited, Platinum, Sport, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Explorer Brake Pads, Rear Part Number: L1MZ-2200-J
$84.96 MSRP: $123.67
You Save: $38.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Rear Pads
- Position: Rear
- Replaces: BRF-1877, L1MZ-2200-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Explorer | Base, King Ranch, Limited, Limited Hybrid, Platinum, Platinum Hybrid, ST, ST-Line, Timberline, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Explorer Brake Pads, Rear Part Number: L1MZ-2200-H
$76.94 MSRP: $112.00
You Save: $35.06 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Replaces: BRF-1879, L1MZ-2200-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Explorer | Base, King Ranch, Limited, Limited Hybrid, Platinum, Platinum Hybrid, ST, ST-Line, Timberline, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Explorer Brake Pads, Front Part Number: L1MZ-2001-G
$145.42 MSRP: $211.67
You Save: $66.25 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: BRF-1886, L1MZ-2001-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Explorer | Base, King Ranch, Limited, Limited Hybrid, Platinum, Platinum Hybrid, ST, ST-Line, Timberline, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Explorer Brake Shoes Part Number: 2U2Z-2V200-JARM
Product Specifications
- Other Name: Remanufactured Kit - Brake Shoe And Lining; Parking Brake Shoe; Shoes
- Replaces: XU2Z-2V200-UARM, F77Z-2200-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford Explorer | Eddie Bauer, Limited, Sport, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Explorer Brake Pads Part Number: F79Z-2001-AA
Product Specifications
- Other Name: Kit - Brake Shoe; Disc Brake Pad Set; Front Pads; Pads
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1991-1994 Ford Explorer | Eddie Bauer, Limited, Sport, XL, XLT | 6 Cyl 4.0 L GAS

| Page 1 of 2 |Next >

1-20 of 21 Results

Ford Explorer Brake Pads

OEM Brake Pads boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Pads with long life and a perfect fit. Come to our website and find genuine Ford Explorer parts. We keep a wide inventory of OEM Explorer parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Explorer Brake Pads are the specific parts that apply the force of friction to the brake rotor and help in slowing down of the vehicle as it transforms the kinetic energy to thermal energy. These pads are normally composed of metals and various synthetic material to be resistant to high temperatures, which in normal usage range up to 200 degrees Celsius. Brake pads have steel backing plates with friction material that wears on the rotor to generate the needed friction for braking. The brake pads are again of different categories namely the non metallic, the semi metallic, the fully metallic and the ceramic ones where each of them holds different characteristics like the friction, wear of the material, noise level. Maintenance and replacement of brake pads are recommended on a regular basis so that they function effectively and of course safely, there are indicators that notify the driver that it is time for a change of the pads. Choice of brake pads plays a big part in having good braking and zero incidences such as brake fade, or mighty rotor wear.

Ford Explorer Brake Pads Parts and Q&A

Brake Pads, Front
2U2Z-2V001-YA
Q: How to service and repair front brake pads on Ford Explorer?
A:
The front brake pad service starts with drawing brake fluid from the master cylinder reservoir until it reaches half level. Begin by raising and supporting the vehicle before taking out both wheel and tire assembly. You must install fresh pads only if their top metal backing plate exceeds the defined thickness limit or shows wear damage while also requiring installation of new pads in complete axle sets. Check the pads for damage or contamination before untightening the lower bolt of the right caliper and the upper bolt of the left caliper. Remove the Brake Disc rotor pads and stainless slippers after rotating the disc Brake Caliper to an opposite position from the rotor. Any detected cracks on the brake disc will require installation of a new brake disc. Machine the brake disc when braking causes vibrations to appear in the steering wheel and seat or brake pedal. The machining process becomes necessary for heavily scored brake discs similar to those from lining wear that reaches the backing plate. The brake disc minimum thickness requirement should also be measured during this operation. Failure to meet brake disc specifications directs the technicians to install a new brake disc as replacement. The disc brake caliper requires dismantling due to the presence of leaks during inspection. Installation requires a suitable suction device to extract brake fluid from the master cylinder then cleaning occurs on support bracket and slipper surfaces before installation. The installation process requires installing slippers and pads according to piston compression rules with C-clamp and wooden block usage along with potential master cylinder fluid reduction. After placing the disc brake caliper inside the anchor bracket, install the caliper bolt and replace the wheel along with its attached tire. A complete brake system inspection must conclude with a functional system check.
Brake Pads, Rear
8L2Z-2V200-B
Q: How to service the rear brake pads on Ford Explorer?
A:
When servicing the rear brake pads one should use brake fluid that meets manufacturer requirements but avoid using any remaining fluid as it may cause damage by introducing contaminants. The proper braking performance requires new brake pads or shoes on both sides of an axle to avoid uneven stopping power. You should inspect the brake fluid in the master cylinder reservoir then drain it until it reaches half-way up the tank if needed. Proceed to eliminate the wheel in addition to the tire. Pry tools must avoid entering the sight hole since doing so will damage caliper Pistons and any attempt to let the Brake Caliper hang from the hose can result in hose damage. Support the caliper with mechanic's wire after uninstalling the two brake caliper guide pin bolts from their positions. Users should inspect the brake pads for signs of wear while checking the Brake Disc for any need in machining or replacing. Discard the brake pad clips followed by removing the two brake pads. It is important to know that a single brake disc pad kit contains linings that cover both sides of the pad installation. After installing brake pad clips together with the brake pads maintain the piston and boots safe by using a worn brake pad to push the caliper piston into the caliper bores through the suitable tool. Equip the brake caliper and add the two brake caliper guide pin bolts while tightening them to 32 Nm (24 lb-ft). Begin by adding clean specified brake fluid into the brake master cylinder reservoir before replacing the wheel along with the tire. Several brake operations should be applied to check that braking functions properly.