How to Service and Repair the Rack and Pinion on Rear-Wheel Drive on Ford Ranger?

The second step for servicing and repairing the rack and pinion on vehicles with rear-wheel drive involves initial front wheel and tire removal. Place the steering wheel in a direct position before you extract the ignition key and lock the wheel into its current state. The power steering fluid cooler has to be taken off in models which come with a 4.0L engine. Guide tightness to 80 Nm (59 lb-ft) for the newly installed nuts before inserting new cotter pins. Make sure to protect the tie-rod boot during usage of the Tie-Rod End Remover before peeling the outer tie-rod ends from wheel spindles. Remove the adapter from the ball end then coat the tie-rod end stud and ball end of the remover with grease. Disconnection of the lower steering column shaft from the rack and pinion requires no column rotation because it can damage the Clock Spring; any column rotation requires a Clock Spring removal and recentering process. Install a fresh bolt to connect the lower steering column shaft with the rack and pinion while tightening it to 55 Nm (41 lb-ft). Discard the old bolt. To disconnect the pressure and return lines you must first remove the steering line clamp plate nut and discard its O-ring seals after which new connections should be tightened to 35 Nm (26 lb-ft). Prevent dirt infiltration of the system by plugging or capping all rack and pinion ports alongside the pressure line and return line. Building up force on the rack and pinion studs protects the fluid tubes from damage then you can pull out the two rack and pinion nuts keeping the new nuts tightened to 150 Nm (111 lb-ft). In case removal is required, proceed by taking out the outer tie-rod ends. New O-ring seals demand installation when disconnecting power steering lines to stop fluid leakages. The power steering system must be properly filled during installation plus front toe adjustments must be performed when needed.

OEM Ford Ranger Rack And Pinion

Steering Rack And Pinion

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Rack And Pinions found

View related parts
Ford Ranger Steering Gear Part Number: F8TZ-3504-ACRM
$294.90 MSRP: $474.55
You Save: $179.65 (38%)
ADD TO CART
Product Specifications
- Other Name: Remanufactured Gear Assembly - Steering; Steering Gear Box; Steering Gearbox; Gear Assembly; Steering Gear Assembly
- Replaces: F8TZ-3504-ABRM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1985-1997 Ford Ranger | Base, Custom, GT, S, S Plus, Splash, Sport, STX, XL, XL Sport, XLS, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.3 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 2.9 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Sector Shaft, Front Part Number: F6AZ-3575-AA
$132.49 MSRP: $183.29
You Save: $50.80 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Steering Gear Sector; Steering Gear Sector Shaft, Front; Pitman Shaft; Shaft & Sector
- Position: Front
- Replaces: EOAZ-3575-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Ranger | Custom, S, Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 2.9 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Steering Gear Part Number: 9L5Z-3504-ARM
$278.47 MSRP: $437.67
You Save: $159.20 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Remanufactured Gear Assembly - Steering; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Assembly - Steering
- Manufacturer Note: Remanufactured
- Replaces: 9L5Z-3504-D, 8L5Z-3504-D, 8L5Z-3504-A, 7L5Z-3504-AD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2011 Ford Ranger | Sport, STX, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Steering Gear Part Number: KB3Z-3504-B
$1375.28 MSRP: $2209.09
You Save: $833.81 (38%)
ADD TO CART
Product Specifications
- Other Name: Gear Assembly - Steering; Gear Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Steering Gear, Front Part Number: KB3Z-3504-A
$1375.28 MSRP: $2209.09
You Save: $833.81 (38%)
ADD TO CART
Product Specifications
- Other Name: Gear Assembly - Steering; Rack and Pinion Assembly, Front; Steering Gearbox; Gear Assembly
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2020 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Steering Gear Part Number: 1L5Z-3504-DARM
$554.40 MSRP: $890.91
You Save: $336.51 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Remanufactured Gear - Rack And Pinion Steering; Rack and Pinion Assembly; Steering Gearbox; Rack & Pinion; Gear Assembly; Gear - Rack And Pinion Steering
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Ranger | XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Ranger Steering Gear Part Number: 1L5Z-3504-CARM
$555.53 MSRP: $892.73
You Save: $337.20 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Remanufactured Gear - Rack And Pinion Steering; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear - Rack And Pinion Steering
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Ranger | Edge, Tremor, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Steering Gear Part Number: F87Z-3504-JCRM
Product Specifications
- Other Name: Remanufactured Gear Assembly - Steering; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly
- Manufacturer Note: Parts List No. 30 Warranty Eligible, Super cab, SPR-LU,NB,SB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Ranger | Splash, XL, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Steering Gear Part Number: F87Z-3504-LCRM
Product Specifications
- Other Name: Remanufactured Gear Assembly - Steering; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Ford Ranger | Splash, XL, XLT | 4 Cyl 2.5 L GAS
View related parts
Ford Ranger Steering Gear Part Number: F87Z-3504-KCRM
Product Specifications
- Other Name: Remanufactured Gear Assembly - Steering; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Assembly - Steering
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Ranger | Edge, Splash, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Valve Part Number: F6TZ3D517DA
Product Specifications
- Other Name: Shaft Assembly; Steering Rack; Input Shaft; Control Assembly; Worm & Ball; Rack Assembly; Control Shaft; Shaft & Sector
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989-1997 Ford Ranger | Custom, GT, S, S Plus, Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 2.9 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Worm Gear, Steel Part Number: E3TZ3524C
Product Specifications
- Other Name: Shaft And Nut Assembly - Steel; Steering Gearbox; Input Shaft; Pinion Shaft; Shaft Assembly; Ball Nut & Shaft; Shaft
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1997 Ford Ranger | Base, Custom, GT, S, S Plus, Splash, Sport, STX, XL, XL Sport, XLS, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.3 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 2.9 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Steering Gear Part Number: E3TZ3504A
Product Specifications
- Other Name: Steering Gear & Linkage; Steering Gearbox; Gear Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1997 Ford Ranger | Base, Custom, GT, S, S Plus, Splash, Sport, STX, XL, XL Sport, XLS, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.3 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 2.9 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Steering Gear Part Number: 9L5Z-3504-CRM
Product Specifications
- Other Name: Remanufactured Gear Assembly - Steering; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Assembly - Steering
- Manufacturer Note: Remanufactured
- Replaces: 7L5Z-3504-CD, 8L5Z-3504-C, 9L5Z-3504-F, STG-417, STG-365, 8L5Z-3504-F, STG-297
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2011 Ford Ranger | Edge, FX4, Sport, STX, XL, XLT | 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Idle Speed Control Part Number: EOAZ-3575-A
Product Specifications
- Other Name: Shaft - Steering Gear Sector; Idle Air Control Valve; Idle Control Motor; Sector Shaft; Pitman Shaft; Pressure Metering Valve; Shaft & Sector; Shaft
- Replaced by: F6AZ-3575-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1992 Ford Ranger | Base, Custom, GT, S, S Plus, Sport, STX, XL, XLS, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.3 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 2.9 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Steering Gear Part Number: 1L5Z-3504-EARM
Product Specifications
- Other Name: Remanufactured Gear - Rack And Pinion Steering; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear - Rack And Pinion Steering
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Ranger | Edge, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Steering Gear Part Number: 9L5Z-3504-BRM
$354.83 MSRP: $560.00
You Save: $205.17 (37%)
Product Specifications
- Other Name: Remanufactured Gear Assembly - Steering; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Assembly - Steering
- Manufacturer Note: Remanufactured
- Replaces: STG-364, 8L5Z-3504-E, 8L5Z-3504-B, 9L5Z-3504-E, 7L5Z-3504-BC, 7L5Z-3504-BB, STG-290, STG-416, STG-395
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2011 Ford Ranger | Edge, FX4, Sport, STX, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS

Ford Ranger Rack And Pinion

OEM Rack And Pinion boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Rack And Pinion with long life and a perfect fit. Come to our website and find genuine Ford Ranger parts. We keep a wide inventory of OEM Ranger parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Steering Rack in Ford Ranger vehicles is an essential mechanism that convert the linear turning of the steering wheel into the lateral movement of the front wheels. This kind of mechanism is called rack and pinion whereby there is a pinion which is linked to the steering column and a rack which is housed in a metal tube, which is connected to the tie-rods and steering knuckles. Ford Rangers mainly incorporate power assisted steering system using a rack and pinion design helps to reduce the effort required in steering via a hydraulic or electrical system. Earlier modes equipped with manual racks in contrast the present models of Ford Rangers are known to incorporate hydraulic ones which are numerated by using pressure in the fluid to enable steering. Subtypes of gears for instance, straight and helical racks may contribute to a difference of performance with a leaning towards the straight gears due to their effectiveness and low temperatures. On the whole, the Steering Rack in Ford Ranger cars is critically important to achieve the right chord and response of the car's steering.

Ford Ranger Rack And Pinion Parts and Q&A

Steering Gear
9L5Z-3504-ARM
Q: How to Service and Repair the Rack and Pinion on Rear-Wheel Drive on Ford Ranger?
A:
The second step for servicing and repairing the rack and pinion on vehicles with rear-wheel drive involves initial front wheel and tire removal. Place the Steering Wheel in a direct position before you extract the ignition key and lock the wheel into its current state. The power steering fluid cooler has to be taken off in models which come with a 4.0L engine. Guide tightness to 80 Nm (59 lb-ft) for the newly installed nuts before inserting new cotter pins. Make sure to protect the tie-rod boot during usage of the Tie-Rod End Remover before peeling the outer tie-rod ends from wheel spindles. Remove the adapter from the ball end then coat the tie-rod end stud and ball end of the remover with grease. Disconnection of the lower steering column shaft from the rack and pinion requires no column rotation because it can damage the Clock Spring; any column rotation requires a Clock Spring removal and recentering process. Install a fresh bolt to connect the lower steering column shaft with the rack and pinion while tightening it to 55 Nm (41 lb-ft). Discard the old bolt. To disconnect the pressure and return lines you must first remove the steering line clamp plate nut and discard its O-ring seals after which new connections should be tightened to 35 Nm (26 lb-ft). Prevent dirt infiltration of the system by plugging or capping all rack and pinion ports alongside the pressure line and return line. Building up force on the rack and pinion studs protects the fluid tubes from damage then you can pull out the two rack and pinion nuts keeping the new nuts tightened to 150 Nm (111 lb-ft). In case removal is required, proceed by taking out the outer tie-rod ends. New O-ring seals demand installation when disconnecting power steering lines to stop fluid leakages. The power steering system must be properly filled during installation plus front toe adjustments must be performed when needed.