How to service and repair the driveshaft slip yoke on Ford Ranger?

Start by setting the driveshaft on a proper workbench with no vise clamp that could potentially harm the components during repairs of the slip yoke. The first step involves properly indexing the driveshaft alongside the slip yoke before clipping and throwing away the slip-yoke boot clamps to extract the slip yoke from the driveshaft. Check the slip-yoke boot for damage then throw it away if needed. Examine lubricant located on the driveshaft splines together with inside the slip-yoke for signs of contamination then check components for wear before replacing them if needed. When assembling the driveshaft fit only a new small driveshaft slip-yoke boot clamp onto the stub shaft before placing the smaller end of the slip-yoke boot on the stub shaft. The Keystone Clamp Installer helps in crimping the boot clamp while you install the slip-yoke onto the driveshaft. Fit 10 g (0.24 oz) of grease into the slip-yoke boot and apply it to the splines while pulling the boot toward the driveshaft. Use new position large slip-yoke boot clamp while matching index marks and place slip-yoke into position. The driveshaft assembled length specification must be set through stub shaft weld measurement to slip-yoke end point along with boot groove placement verification. All surfaces should be free from extra grease. To finish the operation bleed air from the boot then use the Keystone Clamp Installer to secure the large boot clamp.

OEM Ford Ranger Slip Yoke

Transmission Slip Yoke

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Slip Yokes found

View related parts
Ford Ranger Slip Yoke
Part Number: F6ZZ-4841-BA
$199.00 MSRP: $289.67
You Save: $90.67 (32%)
ADD TO CART
Product Specifications
- Other Name: Flange - Coupling; Double Cardan CV Centering Yoke; Driveshaft Yokes
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2011, 2000 Ford Ranger | Sport, STX, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Slip Yoke
Part Number: F57Z-4841-DB
$159.96 MSRP: $232.83
You Save: $72.87 (32%)
ADD TO CART
Product Specifications
- Other Name: Flange - Coupling; Double Cardan CV Centering Yoke; Driveshaft Yokes
- Manufacturer Note: Slip yoke
- Replaces: F57Z-4841-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2011, 1998-1999 Ford Ranger | Edge, Splash, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Companion Flange
Part Number: KB3Z-4851-A
$112.10 MSRP: $163.17
You Save: $51.07 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flange
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Yoke, Rear
Part Number: KB3Z-4784-A
$26.79 MSRP: $39.00
You Save: $12.21 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Assembly; Drive Shaft Slip Yoke, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Upper Coupling
Part Number: KB3Z-3A525-A
$118.30 MSRP: $182.05
You Save: $63.75 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coupling And Universal Joint - Steering Shaft; Steering Shaft Universal Joint, Upper; Coupling; Coupling And Uj - Steering Shaft
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Slip Yoke
Part Number: F57Z-4841-BA
Product Specifications
- Other Name: Flange - Coupling; Double Cardan CV Centering Yoke; Driveshaft Yokes
- Manufacturer Note: Slip yoke
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2011, 1998-1999 Ford Ranger | Edge, Splash, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Slip Yoke, Rear
Part Number: E5TZ-4841-C
Product Specifications
- Other Name: Flange - Coupling; Double Cardan CV Centering Yoke; Driveshaft Yokes
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2001 Ford Ranger | Edge, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Slip Yoke
Part Number: FO9Z4841A
Product Specifications
- Other Name: Flange Coupling - Slip Yoke; Double Cardan CV Centering Yoke; Driveshaft Yokes; Front Yoke; Front Slip Yoke
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Ranger | Custom, S, Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 2.9 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Slip Yoke
Part Number: 6L5Z-4841-B
Product Specifications
- Other Name: Flange - Coupling; Double Cardan CV Centering Yoke; Driveshaft Yokes
- Replaces: 4L5Z-4841-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2011 Ford Ranger | Edge, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS

Ford Ranger Slip Yoke

Welcome to our website where you can discover high-quality, genuine Ford Ranger Slip Yoke. We offer an extensive inventory of OEM Ford Ranger Slip Yoke at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Ford Ranger Slip Yoke Parts Questions & Experts Answers

Slip Yoke
F57Z-4841-DB
Q: How to service and repair the driveshaft slip yoke on Ford Ranger?
A: Start by setting the driveshaft on a proper workbench with no vise clamp that could potentially harm the components during repairs of the slip yoke. The first step involves properly indexing the driveshaft alongside the slip yoke before clipping and throwing away the slip-yoke boot clamps to extract the slip yoke from the driveshaft. Check the slip-yoke boot for damage then throw it away if needed. Examine lubricant located on the driveshaft splines together with inside the slip-yoke for signs of contamination then check components for wear before replacing them if needed. When assembling the driveshaft fit only a new small driveshaft slip-yoke boot clamp onto the stub shaft before placing the smaller end of the slip-yoke boot on the stub shaft. The Keystone Clamp Installer helps in crimping the boot clamp while you install the slip-yoke onto the driveshaft. Fit 10 g (0.24 oz) of grease into the slip-yoke boot and apply it to the splines while pulling the boot toward the driveshaft. Use new position large slip-yoke boot clamp while matching index marks and place slip-yoke into position. The driveshaft assembled length specification must be set through stub shaft weld measurement to slip-yoke end point along with boot groove placement verification. All surfaces should be free from extra grease. To finish the operation bleed air from the boot then use the Keystone Clamp Installer to secure the large boot clamp.