How to service the right-hand exhaust manifold on Ford Taurus?

Service of the right-hand exhaust manifold begins with a wiper arm placement at the windshield highest position followed by disconnecting the battery ground cable. First remove the three retaining clips attached to the right-hand cowl panel grille and proceed with the clip on the right-hand cowl extension panel and its three screws. The service begins by disconnecting both the exhaust manifold from the EGR valve tube along with the heated oxygen sensor (HO2S) electrical connector. First remove the three bolts securing the exhaust manifold heat shield and then uninstall the two dual converter Y-pipe to exhaust manifold bolts and the six bolts holding the exhaust manifold before discarding the exhaust manifold gasket. The installation process starts with new exhaust manifold gasket placement while you should install the exhaust manifold using its six bolts and follow a double-tightening scheme beginning with 10 Nm (89 inch lbs.) then proceeding to 22 Nm (16 ft. lbs.). After securing the exhaust manifold heat shield with its three bolts at 10 Nm (89 inch lbs.), install the two dual converter Y-pipe to exhaust manifold bolts with torque set at 40 Nm (30 ft. lbs.). Properly connect the HO2S electrical connector before joining the exhaust manifold to the EGR valve tube. The last steps involve fastening the right-hand cowl extension panel with three screws while keeping the clip on this panel and reinstalling the right-hand cowl panel grille with its three retaining clips followed by reconnecting the battery ground cable.

How to service the left-hand side exhaust manifold on Ford Taurus?

Service of the left-hand side exhaust manifold begins with removing the LH exhaust manifold to pipe nuts and the coolant tube bracket bolt. The vehicle needs support at its height while the technician disassembles the LH Heated Oxygen Sensor (H02S) electrical connector from the coolant tube. The service starts by removing the pin-type retainers and bolts as well as front splash shield and then moving onto the lower exhaust manifold nuts and coolant tube lower bracket bolt. Lower the vehicle first before you take out the upper exhaust nuts and discard the gasket while also removing the exhaust manifold. Installation begins by positioning a new gasket and then fitting the exhaust manifold before nut tightening follows the provided sequence. The installation process requires placing coolant tubes while tightening the bolt followed by reconnection of the LH H02S electrical connector and installation of LH exhaust manifold-to-pipe nuts. Install the coolant tube lower bracket bolt when the vehicle is at the appropriate height before putting on the front splash shield and securing it with pin-type retainers and bolts.

OEM Ford Taurus Exhaust Manifold

Engine Exhaust Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

28 Exhaust Manifolds found

View related parts
Ford Taurus Exhaust Manifold, Passenger Side Part Number: 7T4Z-9430-C
$64.01 MSRP: $93.17
You Save: $29.16 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Right; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2010 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Exhaust Manifold, Passenger Side Part Number: DA5Z-9430-A
$131.68 MSRP: $191.67
You Save: $59.99 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Right
- Position: Passenger Side
- Replaces: AA5Z-9430-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: DA5Z-9431-A
$129.99 MSRP: $200.60
You Save: $70.61 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Left
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: 4F1Z-9431-AA
$132.62 MSRP: $180.47
You Save: $47.85 (27%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Left; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2007 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: 7T4Z-9431-C
$62.42 MSRP: $86.35
You Save: $23.93 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Left; Manifold
- Position: Driver Side
- Replaces: 7T4Z-9431-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2010 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Exhaust Manifold, Passenger Side Part Number: 4F1Z-9430-BA
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Right; Manifold
- Position: Passenger Side
- Replaces: 4F1Z-9430-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Taurus | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Exhaust Manifold, Passenger Side Part Number: AT4Z-9430-B
$60.34 MSRP: $87.83
You Save: $27.49 (32%)
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Right; Manifold
- Position: Passenger Side
- Replaces: AT4Z-9430-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Exhaust Manifold, Passenger Side Part Number: F6DZ9430A
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Ford Taurus | SHO | 8 Cyl 3.4 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: E6AZ9431E
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1993 Ford Taurus | GL, L, LX, SHO | 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: F48Z9431E
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1988-1995 Ford Taurus | GL, L, LX, SE | 6 Cyl 3.8 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: F4DZ9431C
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1995 Ford Taurus | GL, LX, SE, SHO | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: F5DZ9431C
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996 Ford Taurus | G, GL, LX, SHO | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 8 Cyl 3.4 L GAS
View related parts
Ford Taurus Manifold, Passenger Side Part Number: F6DZ9430L
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Ford Taurus | G, GL, LX, SE, SE Comfort | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: F6DZ9431A
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Ford Taurus | SHO | 8 Cyl 3.4 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: F6DZ-9431-R
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Ford Taurus | G, GL, LX, SE, SE Comfort | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Manifold, Driver Side Part Number: F6DZ9431S
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Ford Taurus | G, GL, LX, SE, SE Comfort | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Exhaust Manifold, Passenger Side Part Number: F7DZ9430EA
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford Taurus | G, GL, LX, SE, SE Comfort, SHO | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 8 Cyl 3.4 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: F7DZ9431FB
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford Taurus | G, GL, LX, SE, SE Comfort, SHO | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 8 Cyl 3.4 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: YF1Z-9431-GB
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Left; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Ford Taurus | SE, SE Comfort, SEL, SES, SVG | 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Exhaust Manifold, Driver Side Part Number: AA5Z-9431-A
Product Specifications
- Other Name: Manifold Assembly - Exhaust; Exhaust Manifold, Left
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2013 Ford Taurus | SHO | 6 Cyl 3.5 L GAS

| Page 1 of 2 |Next >

1-20 of 28 Results

Ford Taurus Exhaust Manifold

OEM Exhaust Manifold boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Exhaust Manifold with long life and a perfect fit. Come to our website and find genuine Ford Taurus parts. We keep a wide inventory of OEM Taurus parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Exhaust Manifold of Ford Taurus vehicles largely helps in collection of hot exhaust gases from the engine before they are channeled to the exhaust system to enhance efficient functioning of the engine and discourage the release of toxic gases into the atmosphere. Depending on the configuration of the engine, the manifold is located at different places and is visually meant to ensure that there is no back flow in the intake tract and more importantly, has to ensure proper airflow, which is crucial to the engine. In Ford Taurus vehicles exhaust manifolds have been made of cast iron or stainless steel and different designs have been incorporated in different models over the years. There are after markets called headers which are made to provide less flow resistance and to improve performance by increasing the velocity of the exhaust gases. The only difference that separates standard exhaust manifolds from header is in the fact that the latter product is specifically designed to promote efficient performance of an engine through better arrangement of the exhaust system.

Ford Taurus Exhaust Manifold Parts and Q&A

Exhaust Manifold, Passenger Side
4F1Z-9430-BA
Q: How to service the right-hand exhaust manifold on Ford Taurus?
A:
Service of the right-hand exhaust manifold begins with a Wiper Arm placement at the windshield highest position followed by disconnecting the battery ground cable. First remove the three retaining clips attached to the right-hand cowl panel grille and proceed with the clip on the right-hand cowl extension panel and its three screws. The service begins by disconnecting both the exhaust manifold from the EGR valve tube along with the heated oxygen sensor (HO2S) electrical connector. First remove the three bolts securing the exhaust manifold heat shield and then uninstall the two dual converter Y-pipe to exhaust manifold bolts and the six bolts holding the exhaust manifold before discarding the exhaust manifold gasket. The installation process starts with new exhaust manifold gasket placement while you should install the exhaust manifold using its six bolts and follow a double-tightening scheme beginning with 10 Nm (89 inch lbs.) then proceeding to 22 Nm (16 ft. lbs.). After securing the exhaust manifold heat shield with its three bolts at 10 Nm (89 inch lbs.), install the two dual converter Y-pipe to exhaust manifold bolts with torque set at 40 Nm (30 ft. lbs.). Properly connect the HO2S electrical connector before joining the exhaust manifold to the EGR valve tube. The last steps involve fastening the right-hand cowl extension panel with three screws while keeping the clip on this panel and reinstalling the right-hand cowl panel grille with its three retaining clips followed by reconnecting the battery ground cable.
Exhaust Manifold, Driver Side
YF1Z-9431-GB
Q: How to service the left-hand side exhaust manifold on Ford Taurus?
A:
Service of the left-hand side exhaust manifold begins with removing the LH exhaust manifold to pipe nuts and the coolant tube bracket bolt. The vehicle needs support at its height while the technician disassembles the LH Heated Oxygen Sensor (H02S) electrical connector from the coolant tube. The service starts by removing the pin-type retainers and bolts as well as front splash shield and then moving onto the lower exhaust manifold nuts and coolant tube lower bracket bolt. Lower the vehicle first before you take out the upper exhaust nuts and discard the gasket while also removing the exhaust manifold. Installation begins by positioning a new gasket and then fitting the exhaust manifold before nut tightening follows the provided sequence. The installation process requires placing coolant tubes while tightening the bolt followed by reconnection of the LH H02S electrical connector and installation of LH exhaust manifold-to-pipe nuts. Install the coolant tube lower bracket bolt when the vehicle is at the appropriate height before putting on the front splash shield and securing it with pin-type retainers and bolts.