How to remove and replace the front bumper cover for all on Lincoln MKZ?

All vehicles require front bumper cover replacement after positioning them on a hoist while keeping them in NEUTRAL gear. The first step involves unfastening 6 pin-type retainers located on each bumper side before proceeding to remove the 8 fender splash shield screws that exist across four points on each side. The installation of the next step requires removing the 4 air deflector bolts. The removal of electrical connectors from the fog lamps must happen if the vehicle includes this equipment. Manufacturers should remove 5 bolts that secure the radiator grille's top section for all MKZ models. To remove the radiator grille top on Fusion and Milan models you should first remove 2 bolts and 2 pin-type retainers before taking out the side marker lamp. Unclip the bumper cover by pulling the rearward upper portion out from its mounting bracket until separation occurs while releasing the tabs adhering it to the mounting bracket. The process to attach the new bumper cover requires doing everything in reverse order to the removal steps.

How to service and repair the front bumper cover on Lincoln Town Car?

Service and repair of the front bumper cover requires the removal of center and left-hand (LH) and right-hand (RH) air deflectors as the first step. Release the bolts and each pair of screws from each side along with the wheel well's single screw. You need to remove three nuts individually positioned across both sides of the front bumper cover prior to extracting the whole front bumper cover. Detach the three pushpoints from each side followed by the bolts which allow separation of the front bumper (part number 17757 before removing the bolt. Position the air deflectors above the valance shields and the radiator support before reinstating the installation procedure in the opposite order to finish.

How to service and repair the rear bumper cover on Lincoln Navigator?

The repair service of the Navigator's rear bumper cover starts with removing its pin-type retainers on the upper section. Start by removing the screw holding the rear bumper cover to inner splash shield on both sides and proceed with the three left and right side bumper cover to quarter panel bracket bolts and the two side bumper cover to quarter panel nuts. Service vehicles with parking aid requires removal of the parking aid sensor harness connector. You should lift upwards on the rear bumper cover corners to detach it. Perform the installation process backward from removal steps while properly transferring all involved components during installation of the new bumper cover.

OEM Lincoln Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

229 Bumpers found

View related parts
Lincoln Bumper Cover, Front Upper
Part Number: JL7Z-17D957-DPTM
$1025.85 MSRP: $1519.78
You Save: $493.93 (33%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front Upper
- Manufacturer Note: Paint to match
- Position: Front Upper
Fits the following Lincoln Models:
- Navigator | 2018-2021 | Base, Black Label, L Black Label, L Livery, L Reserve, L Select, Premiere, Reserve, Select | 6 Cyl 3.5 L GAS
View related parts
Lincoln Impact Bar, Front
Part Number: CL1Z-17757-B
$135.09 MSRP: $208.47
You Save: $73.38 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Impact Bar, Front
- Position: Front
- Replaces: 7L1Z-17757-A, CL1Z-17757-A
Fits the following Lincoln Models:
- Navigator | 2007-2017 | Base, L, L Luxury, L Reserve, L Select, L Ultimate, Luxury, Reserve, Select, Ultimate | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Lincoln Impact Bar, Front
Part Number: JL1Z-17757-A
$254.17 MSRP: $277.48
You Save: $23.31 (9%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Impact Bar, Front
- Position: Front
Fits the following Lincoln Models:
- Navigator | 2018-2024 | Base, Black Label, L Base, L Black Label, L Livery, L Reserve, L Select, Premiere, Reserve, Select | 6 Cyl 3.5 L GAS
View related parts
Lincoln Bumper Cover, Front
Part Number: 9L7Z-17D957-APTM
$478.14 MSRP: $749.67
You Save: $271.53 (37%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front
- Position: Front
Fits the following Lincoln Models:
- Navigator | 2009-2014 | Base, L | 8 Cyl 5.4 L FLEX
View related parts
Lincoln Bumper Cover
Part Number: EP5Z-17D957-DPTM
$537.68 MSRP: $789.55
You Save: $251.87 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover
- Replaces: DP5Z-17D957-DAPTM
Fits the following Lincoln Models:
- MKZ | 2013-2016 | Base, Black Label, Black Label Hybrid, Hybrid | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln Bumper Cover, Front
Part Number: 7L7Z-17D957-APTM
$418.58 MSRP: $614.65
You Save: $196.07 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Position: Front
Fits the following Lincoln Models:
- Navigator | 2007-2008 | Base, L, L Luxury, L Ultimate, Luxury, Ultimate | 8 Cyl 5.4 L GAS
View related parts
Lincoln Reinforcement, Rear
Part Number: 4L1Z-17906-BA
$549.79 MSRP: $754.32
You Save: $204.53 (28%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear
- Position: Rear
Fits the following Lincoln Models:
- Navigator | 2004-2005 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Reinforcement, Rear
Part Number: 5L1Z-17906-AA
$579.45 MSRP: $795.01
You Save: $215.56 (28%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear
- Position: Rear
Fits the following Lincoln Models:
- Navigator | 2005-2006 | Base, Luxury, Ultimate | 8 Cyl 5.4 L GAS
View related parts
Lincoln Bumper Cover, Rear Upper
Part Number: JL7Z-17K835-DBPTM
$674.92 MSRP: $999.88
You Save: $324.96 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Cover, Rear Upper
- Position: Rear Upper
- Replaces: JL7Z-17K835-DAPTM
Fits the following Lincoln Models:
- Navigator | 2018-2021 | L Black Label, L Livery, L Reserve, L Select | 6 Cyl 3.5 L GAS
View related parts
Lincoln Lower Cover, Rear
Part Number: JL7Z-17F828-BCPTM
$159.11 MSRP: $231.60
You Save: $72.49 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper - Extension; Bumper Cover, Rear Lower
- Position: Rear Lower
- Replaces: JL7Z-17F828-BB, JL7Z-17F828-BPTM
Fits the following Lincoln Models:
- Navigator | 2018-2021 | L Black Label, L Livery, L Reserve, L Select | 6 Cyl 3.5 L GAS
View related parts
Lincoln Lower Cover, Rear
Part Number: AE9Z-17K835-C
$129.46 MSRP: $199.23
You Save: $69.77 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper - Extension; Valance Panel, Rear
- Manufacturer Note: Medium Dark Platinum
- Position: Rear Lower
Fits the following Lincoln Models:
- MKT | 2010-2019 | Base, EcoBoost, Livery, Premiere, Reserve | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln Lower Cover
Part Number: FA1Z-17F828-HB
$254.94 MSRP: $397.10
You Save: $142.16 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper - Extension
- Replaces: FA1Z-17K835-HA
Fits the following Lincoln Models:
- MKX | 2016-2018 | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln Bumper Cover
Part Number: 8H6Z-17K835-DAPTM
$333.03 MSRP: $489.03
You Save: $156.00 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover
- Replaces: 6H6Z-17K835-BBPTM
Fits the following Lincoln Models:
- MKZ | 2007-2009 | Base | 6 Cyl 3.5 L GAS
- Zephyr | 2006 | Base | 6 Cyl 3.0 L GAS
View related parts
Lincoln Bumper Cover
Part Number: 2L7Z-17K835-CAA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
Fits the following Lincoln Models:
- Navigator | 2003-2006 | Base, Luxury, Ultimate | 8 Cyl 5.4 L GAS
View related parts
Lincoln Reinforcement, Rear
Part Number: 5L1Z-17906-BA
Product Specifications
- Other Name: Bumper Assembly - Rear
- Position: Rear
Fits the following Lincoln Models:
- Navigator | 2005-2006 | Base, Luxury, Ultimate | 8 Cyl 5.4 L GAS
View related parts
Lincoln Bumper Cover
Part Number: 5L7Z-17D957-CAA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
Fits the following Lincoln Models:
- Navigator | 2005-2006 | Base, Luxury, Ultimate | 8 Cyl 5.4 L GAS
View related parts
Lincoln Bumper Cover
Part Number: 5L7Z-17K835-BAPTM
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
Fits the following Lincoln Models:
- Navigator | 2005-2006 | Base, Luxury, Ultimate | 8 Cyl 5.4 L GAS
View related parts
Lincoln Bumper, Rear
Part Number: YL7Z-17906-AA
Product Specifications
- Other Name: Bumper Assembly - Rear
- Position: Rear
Fits the following Lincoln Models:
- Navigator | 1998-2002 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Bumper Cover
Part Number: YL7Z-17K835-AA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Primed-paint to match, w/o reverse park aid
Fits the following Lincoln Models:
- Navigator | 1998-2002 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Bumper Cover
Part Number: YL7Z-17K835-BA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Primed-paint to match, w/reverse park aid
Fits the following Lincoln Models:
- Navigator | 2000-2002 | Base | 8 Cyl 5.4 L GAS

| Page 1 of 12 |Next >

1-20 of 229 Results

Lincoln Bumper Parts Questions & Experts Answers

Impact Bar, Front
6E5Z-17757-AA
Q: How to remove and replace the front bumper cover for all on Lincoln MKZ?
A: All vehicles require front bumper cover replacement after positioning them on a hoist while keeping them in NEUTRAL gear. The first step involves unfastening 6 pin-type retainers located on each bumper side before proceeding to remove the 8 fender splash shield screws that exist across four points on each side. The installation of the next step requires removing the 4 air deflector bolts. The removal of electrical connectors from the fog lamps must happen if the vehicle includes this equipment. Manufacturers should remove 5 bolts that secure the radiator grille's top section for all MKZ models. To remove the radiator grille top on Fusion and Milan models you should first remove 2 bolts and 2 pin-type retainers before taking out the side marker lamp. Unclip the bumper cover by pulling the rearward upper portion out from its mounting bracket until separation occurs while releasing the tabs adhering it to the mounting bracket. The process to attach the new bumper cover requires doing everything in reverse order to the removal steps.
Impact Bar, Front
YW1Z-17757-AA
Q: How to service and repair the front bumper cover on Lincoln Town Car?
A: Service and repair of the front bumper cover requires the removal of center and left-hand (LH) and right-hand (RH) air deflectors as the first step. Release the bolts and each pair of screws from each side along with the wheel well's single screw. You need to remove three nuts individually positioned across both sides of the front bumper cover prior to extracting the whole front bumper cover. Detach the three pushpoints from each side followed by the bolts which allow separation of the front bumper (part number 17757 before removing the bolt. Position the air deflectors above the valance shields and the radiator support before reinstating the installation procedure in the opposite order to finish.
Impact Bar
F85Z-17757-AA
Q: How to service and repair the rear bumper cover on Lincoln Navigator?
A: The repair service of the Navigator's rear bumper cover starts with removing its pin-type retainers on the upper section. Start by removing the screw holding the rear bumper cover to inner splash shield on both sides and proceed with the three left and right side bumper cover to quarter panel bracket bolts and the two side bumper cover to quarter panel nuts. Service vehicles with parking aid requires removal of the parking aid sensor harness connector. You should lift upwards on the rear bumper cover corners to detach it. Perform the installation process backward from removal steps while properly transferring all involved components during installation of the new bumper cover.