How to remove and replace the front parking brake cable on Mercury Mariner?

Start the front parking brake cable removal by putting the vehicle into neutral gear before hoisting it up. Proceed by taking away the parking brake control unit followed by the front driver seat. You should first undo the three bolts sustaining the front parking brake cable bracket then torque them to 23 Nm (17 lb-ft) when reinstalling. Detach the front parking brake cable from the rear parking brake cable connector after opening the locking tab and disengage the conduit from the left rear parking brake cable. Last, you need to detach the front parking brake cable pass-through grommet from below the vehicle body. The installation process should be completed by performing the reverse steps of removal.

How to service and repair the rear parking brake cable on Mercury Mariner?

The rear parking brake cable servicing and repair process starts with removing drum brake shoes from rear drum brake units. The servicing procedure for rear parking brakes starts with placing a disc brake vehicle in neutral position on a hoist. The floor console boot clips holding the parking brake control need inward pressure at their bases so you can remove the boot by raising it above the lever. The service and repair of the rear parking brake cable requires disconnecting the cable connector from the LH rear parking brake cable at the equalizer while loosening its front cable adjuster nut. The installation of the two parking brake equalizer bracket bolts requires torque settings at 9 Nm (80 inch lbs.) and this should also be done if you are removing the LH rear parking brake cable. The process should include unhooking the front parking brake cable from the equalizer bracket through pressure on the cable conduit locking tabs and removing the cable-to-fuel tank strap clip. Unclamp the cable bracket-to-body bolt before reinstallation and fasten it to 23 Nm (17 ft. lbs.) then secure the cable bracket-to-trailing arm bolt at 23 Nm (17 ft. lbs.). Users should compress the rear parking brake cable conduit locking tabs to extract the cable assembly through the brake backing plate of drum brake vehicles. To service disc brakes you should do two things; first let go of the rear parking brake cable end from the parking brake actuator lever then compress the cable conduit locking tabs. Reversing the removal process should be completed by readjusting the parking brake cable as required.

OEM Mercury Mariner Parking Brake Cable

Emergency Parking Brake Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Parking Brake Cables found

View related parts
Mercury Mariner Front Cable Part Number: 5L8Z-2853-AA
$25.79 MSRP: $35.67
You Save: $9.88 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Rear Cable Part Number: 6L8Z-2A635-L
$44.77 MSRP: $71.09
You Save: $26.32 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Replaces: 6L8Z-2A635-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Rear Cable, Passenger Side Part Number: 6L8Z-2A635-J
$41.22 MSRP: $65.45
You Save: $24.23 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Passenger Side
- Replaces: 6L8Z-2A635-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Mariner | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Rear Cable, Driver Side Part Number: AL8Z-2A635-A
$58.20 MSRP: $80.52
You Save: $22.32 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Mariner Rear Cable, Passenger Side Part Number: AL8Z-2A635-B
$51.91 MSRP: $71.81
You Save: $19.90 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Mariner Rear Cable, Passenger Side Part Number: 8L8Z-2A635-A
$32.51 MSRP: $44.98
You Save: $12.47 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Mercury Mariner | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Mariner Rear Cable, Driver Side Part Number: 8M6Z-2A635-B
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Parking Brake Cable; Brake Cable
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Mercury Mariner | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Mariner Rear Cable, Passenger Side Part Number: 9L8Z-2A635-B
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Passenger Side
- Replaces: 9L8Z-2A635-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Mercury Mariner | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Rear Cable, Passenger Side Part Number: 8M6Z-2A635-A
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Mercury Mariner | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Mariner Rear Cable, Driver Side Part Number: 6L8Z-2A635-M
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Driver Side
- Replaces: 6L8Z-2A635-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Rear Cable, Passenger Side Part Number: 6L8Z-2A635-K
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Passenger Side
- Replaces: 6L8Z-2A635-H
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Rear Cable, Driver Side Part Number: 8L8Z-2A635-B
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Mariner | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Front Cable Part Number: 8L8Z-2853-A
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

Mercury Mariner Parking Brake Cable

OEM Parking Brake Cable boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Parking Brake Cable with long life and a perfect fit. Come to our website and find genuine Mercury Mariner parts. We keep a wide inventory of OEM Mariner parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Mercury Mariner Parking Brake Cable is a key component that forms the Mercury Mariner vehicle as it displays its reliability and performance. This cable is an important component of the parking brake system that helps the Mercury Mariner to safely park and stay parked, and especially on an inclined plane, thereby providing a measure of comfort and convenience. Suitable for use with a wide range of Mercury Mariner models, the Parking Brake Cable links the parking brake to the rest of the braking system and was designed to give an additional layer of security against rolling when parked, as well as a form of emergency braking if required. In time, Mercury Mariner has come to be known for its reliability and this is where a Parking Brake Cable comes in handy. It is important to maintain the Parking Brake Cable because wear or stretching of the cable pose some potential risks such as a failure in the parking brakes system. Illuminated parking brake light can act as the signal that there are problems with the cable usage, thus stressing on the necessity of the inspections. For instance, the Mercury Mariner Parking Brake Cable has features that make it unique in the automotive market; this includes the construction of the product and its reliability to help drivers with their cars. Due to its previous achievements such as a Consumers Digest optimal Buy, the Mercury Mariner with the help of its reliable Parking Brake Cable remains a popular car for people who need a compact crossover SUV that is efficient as well as reliable.

Mercury Mariner Parking Brake Cable Parts and Q&A

Front Cable
8L8Z-2853-A
Q: How to remove and replace the front parking brake cable on Mercury Mariner?
A:
Start the front parking brake cable removal by putting the vehicle into neutral gear before hoisting it up. Proceed by taking away the parking brake control unit followed by the front driver seat. You should first undo the three bolts sustaining the front parking brake cable bracket then torque them to 23 Nm (17 lb-ft) when reinstalling. Detach the front parking brake cable from the rear parking brake cable connector after opening the locking tab and disengage the conduit from the left rear parking brake cable. Last, you need to detach the front parking brake cable pass-through grommet from below the vehicle body. The installation process should be completed by performing the reverse steps of removal.
Rear Cable, Driver Side
8M6Z-2A635-B
Q: How to service and repair the rear parking brake cable on Mercury Mariner?
A:
The rear parking brake cable servicing and repair process starts with removing drum Brake Shoes from rear drum brake units. The servicing procedure for rear parking brakes starts with placing a disc brake vehicle in neutral position on a hoist. The floor console boot clips holding the parking brake control need inward pressure at their bases so you can remove the boot by raising it above the lever. The service and repair of the rear parking brake cable requires disconnecting the cable connector from the LH rear parking brake cable at the equalizer while loosening its front cable adjuster nut. The installation of the two parking brake equalizer bracket bolts requires torque settings at 9 Nm (80 inch lbs.) and this should also be done if you are removing the LH rear parking brake cable. The process should include unhooking the front parking brake cable from the equalizer bracket through pressure on the cable conduit locking tabs and removing the cable-to-fuel tank strap clip. Unclamp the cable bracket-to-body bolt before reinstallation and fasten it to 23 Nm (17 ft. lbs.) then secure the cable bracket-to-trailing arm bolt at 23 Nm (17 ft. lbs.). Users should compress the rear parking brake cable conduit locking tabs to extract the cable assembly through the Brake Backing Plate of drum brake vehicles. To service disc brakes you should do two things; first let go of the rear parking brake cable end from the parking brake actuator lever then compress the cable conduit locking tabs. Reversing the removal process should be completed by readjusting the parking brake cable as required.