How to service and repair the rear AM/FM and satellite radio antenna cables on Mercury Milan?

The first step to repair or service rear AM/FM and satellite radio antenna cables starts with removing the right-hand front and rear door scuff plates. Detach the front antenna cable from the rear antenna cable at the right-hand kick panel followed by removing the right-hand C-pillar trim panel. The rear antenna cable needs to be disconnected from the antenna module of the MKZ model. Before proceeding with service or repair of the rear antenna cables in Fusion/Milan vehicles along with all satellite radio vehicles customers must first remove each assist handle followed by the left-hand C-pillar panel. The antenna cable requires loosening of the bolt before disconnecting it from the antenna position with a final torque setting of 8 Nm (71 lb-in) during reassembly. You must perform two actions: cut the existing co-axial cable ends and remove the enable circuit functionality after disconnecting C237 at the right-hand kick panel. Use pliers to remove the male connector pin retainer while you locate the locking tab with the suitable tool to separate the enable circuit CME44 (BU) from C237-25. Keep the end section of the existing circuit then tape it together with electrical tape. Installation ends with executing the reverse steps from removal.

OEM Mercury Milan Antenna Cable

Radio Antenna Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Antenna Cables found

View related parts
Mercury Milan Antenna Cable Part Number: AE5Z-18812-J
$33.44 MSRP: $45.51
You Save: $12.07 (27%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Extension
- Replaces: AE5Z-18812-C, AE5Z-18812-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Antenna Cable Part Number: AE5Z-18812-H
$21.92 MSRP: $30.32
You Save: $8.40 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Extension
- Manufacturer Note: Body Coaxial Assembly
- Replaces: AE5Z-18812-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Antenna Cable, Front Part Number: AE5Z-18812-E
$25.04 MSRP: $34.64
You Save: $9.60 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable, Front
- Manufacturer Note: Attaches To Radio Receiver
- Position: Front
- Replaces: AE5Z-18812-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Antenna Cable Part Number: 8E5Z-18812-B
$33.85 MSRP: $46.06
You Save: $12.21 (27%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Extension
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Antenna Cable, Front Part Number: AE5Z-18812-D
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable, Front
- Position: Front
- Replaces: 7E5Z-18812-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Mercury Milan | Base, Hybrid, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Antenna Cable Part Number: 8E5Z-18812-A
Product Specifications
- Other Name: Cable Assembly - Extension
- Replaces: 7E5Z-18812-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Antenna Cable Part Number: 6E5Z-18812-CA
Product Specifications
- Other Name: Cable Assembly - Extension
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Antenna Cable Part Number: 6E5Z-18812-BA
Product Specifications
- Other Name: Cable Assembly - Extension
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Antenna Cable, Rear Passenger Side Part Number: 6E5Z-18812-AA
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable, Right
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

Mercury Milan Antenna Cable

OEM Antenna Cable boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Antenna Cable with long life and a perfect fit. Come to our website and find genuine Mercury Milan parts. We keep a wide inventory of OEM Milan parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Mercury Milan Antenna Cable functions as a core part which stands behind the reliability and performance of Mercury Milan vehicles to maintain uninterrupted radio antenna-radio receiver connectivity. The Antenna Cable functions as a key delivery point for audio signals which produces better sound quality to enhance driving entertainment and communication accessibility. The Antenna Cable functions with the range of Mercury Milan vehicles manufactured between 2006 and 2011 while supporting internal and external and satellite antenna configurations to maximize signal reception. Through its design approach and engineering methods the Mercury Milan maintains safe operations and efficient performance through the Antenna Cable to prevent the degradation of radio signals. Monitoring and replacing the Antenna Cable at the right time ensures the Mercury Milan audio system maintains its operational excellence. Since its release brand model Antenna Cable has become known for its reliable performance which makes drivers experience continuous and uninterrupted audio listening. The car Antenna Cable serves a vital safety and functional role because it demonstrates the automaker's dedication to delivering excellent vehicle performance in each model.

Mercury Milan Antenna Cable Parts and Q&A

Antenna Cable
8E5Z-18812-B
Q: How to service and repair the rear AM/FM and satellite radio antenna cables on Mercury Milan?
A:
The first step to repair or service rear AM/FM and satellite radio Antenna cables starts with removing the right-hand front and rear door scuff plates. Detach the front antenna cable from the rear antenna cable at the right-hand kick panel followed by removing the right-hand C-pillar trim panel. The rear antenna cable needs to be disconnected from the antenna module of the MKZ model. Before proceeding with service or repair of the rear antenna cables in Fusion/Milan vehicles along with all satellite radio vehicles customers must first remove each assist handle followed by the left-hand C-pillar panel. The antenna cable requires loosening of the bolt before disconnecting it from the antenna position with a final torque setting of 8 Nm (71 lb-in) during reassembly. You must perform two actions: cut the existing co-axial cable ends and remove the enable circuit functionality after disconnecting C237 at the right-hand kick panel. Use pliers to remove the male connector pin retainer while you locate the locking tab with the suitable tool to separate the enable circuit CME44 (BU) from C237-25. Keep the end section of the existing circuit then tape it together with electrical tape. Installation ends with executing the reverse steps from removal.