How to Service and Repair the Motor and Transmission Mount for the Aisin AW21 Transaxle Support Insulator on Mercury Milan?

Attention should first focus on setting the vehicle in neutral position on a hoist before removing the battery and tending to the battery tray. Begin by removing four screws which hold the LH fender splash shield while setting it aside then continue with removing six pin-type retainers along with the LH front structure-to-subframe splash shield. The service requires uninstallation of two transaxle insulator-to-frame bolts which are found lower on the structure. The propulsion process for the 3.0L engine includes attaching an Engine Lifting Bracket and Universal Adapter Bracket "L" hook to the LH side of the engine before using an Engine Support Bar to support the engine for bolt removal from the transaxle support insulator-to-bracket. The Oil Pan Holding Fixture needs careful alignment to the oil pan bosses to avoid breaking when servicing the exhaust Y-pipe of the 3.5L engine. Position the floor jack along with the Oil Pan Holding Fixture beneath the oil pan and remove the Air Cleaner (ACL) and the transaxle support insulator through bolt. The procedure requires removal of the upper 2 transaxle insulator-to-frame bolts before uninstalling the transaxle insulator from all vehicles. The installer should brush clean rear transaxle support insulator bolts with a wire brush before applying new threadlock during installation. Place the transaxle support insulator in position before securing its upper 2 bolts that need a torque of 62 Nm (46 lb-ft). During transaxle insulator installation into the 3.5L engine you should tighten the through bolt and flagnut to 130 Nm (96 lb-ft). Put away the floor jack together with the Oil Pan Holding Fixture while reattaching the ACL and exhaust Y-pipe. The transaxle support insulator should be installed on all vehicles where technicians must insert the lower 2 transaxle insulators-to-frame bolts and torque them to 62 Nm (46 lb-ft). The LH splash shield requires installation with its 6 pin-type retainers and 4 screws while being secured. The 3.0L engine requires the installation of 2 transaxle support insulator-to-bracket bolts that should have a torque of 90 Nm (66 lb-ft). Reinstall the battery while putting back the battery tray and finish by taking out both the Universal Adapter Bracket "L" hook and Engine Lifting Bracket and Engine Support Bar from the LH side of the engine.

OEM Mercury Milan Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

29 Motor And Transmission Mounts found

View related parts
Mercury Milan Transmission Mount Part Number: 9E5Z-6038-A
$80.12 MSRP: $116.62
You Save: $36.50 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Manual Transmission Mount; Transfer Case Mount
- Replaces: 6E5Z-6038-CB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mercury Milan Front Mount, Passenger Side Part Number: 6E5Z-6038-CK
$68.91 MSRP: $100.30
You Save: $31.39 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Manufacturer Note: Requires Multiple Replacment Parts
- Position: Front Passenger Side
- Replaced by: 9E5Z-6038-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS
View related parts
Mercury Milan Transmission Mount, Driver Side Part Number: 6H6Z-6038-BA
$80.12 MSRP: $116.62
You Save: $36.50 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Transfer Case Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mercury Milan | Base, Premier | 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Torque Strut, Lower Part Number: 9E5Z-6068-C
$37.68 MSRP: $52.13
You Save: $14.45 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut, Lower; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Strut
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Premier | 4 Cyl 2.5 L GAS
View related parts
Mercury Milan Strut Assembly Part Number: 8E5Z-6068-D
$56.76 MSRP: $82.62
You Save: $25.86 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Support Rod; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Torque Strut; Strut
- Replaces: 6E5Z-6068-FC, 6E5Z-6068-B, 6E5Z-6068-A, 8E5Z-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Transmission Mount, Upper Part Number: 8H6Z-6038-A
$83.62 MSRP: $121.72
You Save: $38.10 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount, Upper; Transfer Case Mount
- Position: Upper
- Replaces: 7H6Z-6038-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Premier | 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Transmission Mount, Upper Part Number: 9E5Z-6038-G
$83.50 MSRP: $121.55
You Save: $38.05 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount, Upper; Transfer Case Mount
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Premier | 4 Cyl 2.5 L GAS
View related parts
Mercury Milan Mount Bracket Part Number: 9E5Z-6061-C
$50.88 MSRP: $72.78
You Save: $21.90 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Support; Engine Mount Bracket; Motor Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Premier | 4 Cyl 2.5 L GAS
View related parts
Mercury Milan Transmission Mount Part Number: BE5Z-6038-C
$115.65 MSRP: $168.33
You Save: $52.68 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Transfer Case Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011 Mercury Milan | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Milan Front Mount Part Number: 6E5Z-6038-DF
$111.64 MSRP: $162.50
You Save: $50.86 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: 6E5Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mercury Milan | Base, Premier | 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Mount Bracket Part Number: 9E5Z-6061-D
$46.10 MSRP: $63.78
You Save: $17.68 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Support; Engine Mount Bracket; Motor Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Premier | 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Transmission Mount Bracket, Driver Side Part Number: 6E5Z-6031-GA
Product Specifications
- Other Name: Bracket - Engine Mounting; Automatic Transmission Mount Bracket; Transfer Case Mount; Transmission Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mercury Milan | Base, Premier | 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Transmission Mount Bracket, Upper Part Number: 6E5Z-6031-HA
Product Specifications
- Other Name: Bracket - Engine Mounting; Manual Transmission Mount Bracket, Upper; Transfer Case Mount; Transmission Mount
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mercury Milan Transmission Mount Bracket Part Number: 8E5Z-6031-A
Product Specifications
- Other Name: Bracket - Engine Mounting; Transfer Case Mount; Transmission Mount
- Replaces: 6E5Z-6031-JA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS
View related parts
Mercury Milan Transmission Mount Part Number: BE5Z-6038-A
Product Specifications
- Other Name: Insulator Assembly; Transfer Case Mount
- Replaced by: BE5Z-6038-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Milan Transmission Mount Bracket Part Number: 9E5Z-6038-B
Product Specifications
- Other Name: Insulator Assembly - Engine; Automatic Transmission Mount Bracket; Transfer Case Mount; Insulator Assembly - Engine Support; Transmission Mount
- Replaced by: BE5Z-6038-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Milan Transmission Mount Part Number: BE5Z-6038-B
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Automatic Transmission Mount; Transfer Case Mount; Transmission Mount Bracket
- Replaces: 9E5Z-6038-D, 9E5Z-6038-B, BE5Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Milan Transmission Mount Bracket, Upper Part Number: 9E5Z-6031-A
Product Specifications
- Other Name: Bracket - Engine Mounting; Automatic Transmission Mount Bracket, Upper; Transfer Case Mount; Transmission Mount
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Premier | 4 Cyl 2.5 L GAS
View related parts
Mercury Milan Transmission Mount Bracket Part Number: 9E5Z-6031-B
Product Specifications
- Other Name: Bracket - Engine Mounting; Automatic Transmission Mount Bracket; Transfer Case Mount; Transmission Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Premier | 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Mount Bracket, Front Part Number: 9E5Z-6061-B
Product Specifications
- Other Name: Bracket - Engine Support; Engine Mount Bracket, Front; Motor Mount; Engine Mount Bracket
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)

| Page 1 of 2 |Next >

1-20 of 29 Results

Mercury Milan Motor And Transmission Mount

OEM Motor And Transmission Mount boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Motor And Transmission Mount with long life and a perfect fit. Come to our website and find genuine Mercury Milan parts. We keep a wide inventory of OEM Milan parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Its product Motor And Transmission Mount is something very special as it is highly valued and utilized in making functional Mercury Milan motor vehicles. This Motor And Transmission Mount provides a means through which the transmission is firmly secured in position so as to protect it from vibrations from the engine which would affect its stability and performance during operation. Made to fit the different Mercury Milan models which were manufactured between 2006 and 2011, this Motor And Transmission Mount comes in different forms depending on the type of model that a car owner has. The Motor And Transmission Mount goes further than a mere component of the car; it is an essential factor that boosts the vehicle efficiency and safety. This Motor And Transmission Mount is designed to ensure that there is least movement and thus enhances better handling, less fuel consumption and rough ride quality. However, it is important to note that the Mercury Milan boasts of a good quality well-engineered chassis accompanied with good suspension systems, when the car is complemented by a good Motor And Transmission Mount, it offers excellent handling and drivability. Also, the Motor And Transmission Mount has a more durable construction and design in the automotive market, making the car free from regular maintenance. In summary, the Motor And Transmission Mount is yet another amazing invention in the Mercury brand name and is very crucial in enhancing the engineering of the Mercury Milan.

Mercury Milan Motor And Transmission Mount Parts and Q&A

Strut Assembly
8E5Z-6068-D
Q: How to Service and Repair the Motor and Transmission Mount for the Aisin AW21 Transaxle Support Insulator on Mercury Milan?
A:
Attention should first focus on setting the vehicle in neutral position on a hoist before removing the battery and tending to the battery tray. Begin by removing four screws which hold the LH fender splash shield while setting it aside then continue with removing six pin-type retainers along with the LH front structure-to-subframe splash shield. The service requires uninstallation of two transaxle insulator-to-frame bolts which are found lower on the structure. The propulsion process for the 3.0L engine includes attaching an Engine Lifting Bracket and Universal Adapter Bracket "L" hook to the LH side of the engine before using an Engine Support Bar to support the engine for bolt removal from the transaxle support insulator-to-bracket. The Oil Pan Holding Fixture needs careful alignment to the oil pan bosses to avoid breaking when servicing the exhaust Y-pipe of the 3.5L engine. Position the floor jack along with the Oil Pan Holding Fixture beneath the oil pan and remove the Air Cleaner (ACL) and the transaxle support insulator through bolt. The procedure requires removal of the upper 2 transaxle insulator-to-frame bolts before uninstalling the transaxle insulator from all vehicles. The installer should brush clean rear transaxle support insulator bolts with a wire brush before applying new threadlock during installation. Place the transaxle support insulator in position before securing its upper 2 bolts that need a torque of 62 Nm (46 lb-ft). During transaxle insulator installation into the 3.5L engine you should tighten the through bolt and flagnut to 130 Nm (96 lb-ft). Put away the floor jack together with the Oil Pan Holding Fixture while reattaching the ACL and exhaust Y-pipe. The transaxle support insulator should be installed on all vehicles where technicians must insert the lower 2 transaxle insulators-to-frame bolts and torque them to 62 Nm (46 lb-ft). The LH splash shield requires installation with its 6 pin-type retainers and 4 screws while being secured. The 3.0L engine requires the installation of 2 transaxle support insulator-to-bracket bolts that should have a torque of 90 Nm (66 lb-ft). Reinstall the battery while putting back the battery tray and finish by taking out both the Universal Adapter Bracket "L" hook and Engine Lifting Bracket and Engine Support Bar from the LH side of the engine.