How to Service the Yaw Sensor on Mercury Mountaineer?

Service of the yaw rate sensor begins with disconnecting the battery ground cable. First remove the pin-type retainer then the driver-side floor console finish panel followed by 2 bolt removal and 2 nut removal of the LH instrument panel brace and finally tighten all nuts to 9 Nm (80 inch lbs.) during reinstalls. First remove the 2 heater duct screws from the left-hand side and disconnect the stability control sensor cluster electrical connection. Move the treatment retainers of the stability control sensor cluster away then place them on the side. The process requires removal of stability control sensor cluster bracket nuts and the cluster itself before stable control sensor cluster installation where nuts need tightening to 7 Nm (62 inch lbs.). Within the connection configuration and calibrating procedure for installation of the new stability control sensor cluster reverse the previously removed steps and follow diagnostic tool instructions while using built-in data from the vehicle.

OEM Mercury Mountaineer Yaw Sensor

Yaw Rate Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Yaw Sensors found

View related parts
Mercury Mountaineer Yaw Rate Sensor
Part Number: 7L1Z-3C187-A
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Steering Wheel Speed Sensor; Yaw Sensor; Sensor
- Manufacturer Note: Lateral/Yaw Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Yaw Rate Sensor
Part Number: 6L2Z-3C187-AA
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Steering Wheel Speed Sensor; Yaw Sensor; Sensor
- Manufacturer Note: Lateral/Yaw Sensor
- Replaces: 3C5Z-3C187-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Yaw Rate Sensor
Part Number: 3L2Z-3C296-BA
Product Specifications
- Other Name: Sensor Assembly
- Manufacturer Note: Sensor - Yaw
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Yaw Rate Sensor
Part Number: 3L2Z-3C296-AA
Product Specifications
- Other Name: Sensor Assembly
- Manufacturer Note: Sensor - Yaw
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS

Mercury Mountaineer Yaw Sensor

Welcome to our website where you can discover high-quality, genuine Mercury Mountaineer Yaw Sensor. We offer an extensive inventory of OEM Mercury Mountaineer Yaw Sensor at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Mercury Mountaineer Yaw Sensor Parts Questions & Experts Answers

Yaw Rate Sensor
7L1Z-3C187-A
Q: How to Service the Yaw Sensor on Mercury Mountaineer?
A: Service of the yaw rate sensor begins with disconnecting the battery ground cable. First remove the pin-type retainer then the driver-side floor console finish panel followed by 2 bolt removal and 2 nut removal of the LH instrument panel brace and finally tighten all nuts to 9 Nm (80 inch lbs.) during reinstalls. First remove the 2 heater duct screws from the left-hand side and disconnect the stability control sensor cluster electrical connection. Move the treatment retainers of the stability control sensor cluster away then place them on the side. The process requires removal of stability control sensor cluster bracket nuts and the cluster itself before stable control sensor cluster installation where nuts need tightening to 7 Nm (62 inch lbs.). Within the connection configuration and calibrating procedure for installation of the new stability control sensor cluster reverse the previously removed steps and follow diagnostic tool instructions while using built-in data from the vehicle.