How to service and repair the brake pads for the 4.0L SOHC and 4.6L (3V) disc brake system on 2008 Ford Mustang?

Only brake fluid that meets manufacturer requirements should be used to service and repair brake pads of the 4.0L SOHC and 4.6L (3V) disc brake system. Previously drained fluid poses a risk of damaging components. Proceed to check the brake fluid level in the reservoir then drain away half of the fluid if needed. The procedure starts with mounting mechanic wire to the caliper to support it while you discard both guide pin bolts from the brake caliper assembly. The replacement of brake pads should involve axle set installation to stop brake drag or pull. Throw away the four spring clips. The brake caliper requires inspection for leakage and boot condition followed by replacement if needed while you should check the anchor plate assembly for binding or damage before applying specified grease to guide pins and performing an anchor plate replacement if necessary. During new brake pad installation apply a C-clamp together with a worn brake pad to push caliper pistons into brake bores while making sure to protect the pistons as well as the boots. The brake pad kit installation requires users to mount four new spring clips and two new brake pads as well as all provided hardware. Fasten the brake caliper onto the anchor plate by using two new guide pin bolts that need tightness of 34 Nm (25 lb-ft). The reservoir needs clean specified brake fluid before you apply pressure to the brake pedal several times to confirm correct functioning.

OEM 2008 Ford Mustang Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Brake Pads found

View related parts
2008 Ford Mustang Brake Pads, Front Part Number: 7R3Z-2001-A
$120.45 MSRP: $181.67
You Save: $61.22 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Shoe; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Disc Brake Pad Set
- Position: Front
- Base No.: 2001
- Item Weight: 5.40 Pounds
- Item Dimensions: 6.2 x 3.0 x 4.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7R3Z-2001-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Boss 302, Bullitt, GT, Shelby GT, Shelby GT500, Shelby GT500KR | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 5.8 L GAS
View related parts
2008 Ford Mustang Brake Pads, Front Part Number: 5U2Z-2V001-K
$46.59 MSRP: $66.65
You Save: $20.06 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: 5U2Z-2V001-E, 9R3Z-2001-B, BRF-1405, G2MZ-2V001-AG, BR-1081
- Item Weight: 4.40 Pounds
- Item Dimensions: 8.8 x 5.3 x 2.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5U2Z-2V001-K
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base, GT, Shelby GT500 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford Mustang Brake Pads, Rear Part Number: CR3Z-2200-A
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Rear; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Replaces: 7R3Z-2200-A
- Base No.: 2200
- Item Weight: 2.70 Pounds
- Item Dimensions: 7.0 x 4.8 x 3.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: CR3Z-2200-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Bullitt, GT, Shelby GT, Shelby GT500, Shelby GT500KR | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 5.8 L GAS
View related parts
2008 Ford Mustang Brake Pads, Front Part Number: BR3Z-2001-D
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Disc Brake Pad Set
- Position: Front
- Replaces: 8R3Z-2001-A
- Base No.: 2001
- Item Weight: 5.30 Pounds
- Item Dimensions: 3.5 x 4.9 x 8.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: BR3Z-2001-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base, GT | 6 Cyl 3.7 L GAS, 8 Cyl 4.6 L GAS
View related parts
2008 Ford Mustang Brake Pads, Front Part Number: 9R3Z-2001-A
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Disc Brake Pad Set
- Manufacturer Note: Warranty Eligible
- Position: Front
- Replaces: 7R3Z-2001-B, 6R3Z-2001-A
- Base No.: 2001
- Item Weight: 5.10 Pounds
- Item Dimensions: 3.3 x 5.1 x 8.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9R3Z-2001-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base | 6 Cyl 4.0 L GAS
View related parts
2008 Ford Mustang Brake Pads, Rear Part Number: 8R3Z-2200-A
Product Specifications
- Other Name: Shoe And Lining Assembly; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Disc Brake Pad Set
- Manufacturer Note: Warranty Eligible
- Position: Rear
- Replaces: 5R3Z-2200-B
- Base No.: 2200
- Item Weight: 2.70 Pounds
- Item Dimensions: 3.2 x 4.8 x 7.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8R3Z-2200-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base, GT, Shelby GT500 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford Mustang Front Pads Part Number: 7R3Z-2001-B
Product Specifications
- Other Name: Kit - Brake Shoe; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Brake Pads
- Manufacturer Note: Warranty Eligible
- Position: Front
- Replaced by: 9R3Z-2001-A
- Item Weight: 5.50 Pounds
- Item Dimensions: 3.5 x 4.9 x 8.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7R3Z-2001-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base, GT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS

2008 Ford Mustang Brake Pads

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2008 Ford Mustang Brake Pads available at FordPartsDeal.com. You can confidently purchase our OEM 2008 Ford Mustang Brake Pads as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2008 Ford Mustang Brake Pads Parts Q&A

Q: How to service and repair the brake pads for the 4.0L SOHC and 4.6L (3V) disc brake system on 2008 Ford Mustang?
A: Only brake fluid that meets manufacturer requirements should be used to service and repair brake pads of the 4.0L SOHC and 4.6L (3V) disc brake system. Previously drained fluid poses a risk of damaging components. Proceed to check the brake fluid level in the reservoir then drain away half of the fluid if needed. The procedure starts with mounting mechanic wire to the caliper to support it while you discard both guide pin bolts from the brake caliper assembly. The replacement of brake pads should involve axle set installation to stop brake drag or pull. Throw away the four spring clips. The brake caliper requires inspection for leakage and boot condition followed by replacement if needed while you should check the anchor plate assembly for binding or damage before applying specified grease to guide pins and performing an anchor plate replacement if necessary. During new brake pad installation apply a C-clamp together with a worn brake pad to push caliper pistons into brake bores while making sure to protect the pistons as well as the boots. The brake pad kit installation requires users to mount four new spring clips and two new brake pads as well as all provided hardware. Fasten the brake caliper onto the anchor plate by using two new guide pin bolts that need tightness of 34 Nm (25 lb-ft). The reservoir needs clean specified brake fluid before you apply pressure to the brake pedal several times to confirm correct functioning.