How to Service and Repair the Front Brake Line on Ford E-150?

You should start servicing and fixing the front brake flexible hose after you detach its connection to the wheel speed sensor wiring harness. After removing the brake caliper flow bolt, users need to discard both copper washers but should replace them with new ones before reinstalling the bolt while tightening to 40 Nm of torque (30 lb-ft). The brake flexible hose must have its brake tube fitting disconnected before reinstallation where torques must reach 17 Nm (13 lb-ft). The brake flexible hose can be removed after disconnecting its retaining clip. The final step requires following the opposite steps of removal while performing a brake caliper bleeding procedure. Only factory-certified brake fluid which is clean and new can be used because the use of prior drain fluid creates risks of system pollution and damage to the system. The chemical nature of brake fluid causes damage to painted surfaces and plastic materials so promptly clean away any fluid accident with water. You can access emergency medical details about Ford and Motorcraft products by dialing 1-800-959-3673 from the United States or Canada along with available product Material Safety Data Sheets (MSDS).

How to Service and Repair the Rear Brake Line Flexible Hoses on Ford E-150?

The first step for servicing or repairing rear brake flexible hoses requires removal of the wheel and tire. You should remove the brake caliper flow bolt followed by discarding the two copper washers before tightening the new bolt to 40 Nm (30 lb-ft) during installation. When reinstalling disconnect the brake tube fitting from the LH brake flexible hose junction block with a torque of 18 Nm (13 lb-ft). The repair of the RH brake flexible hose follows brake tube servicing by removing the brake flexible hose bracket bolt and the RH brake flexible hose which needs to be fastened at 25 Nm (18 lb-ft) torque when replacing it. When installing the LH brake flexible hose then disconnect its brake tube fitting and make sure it reaches 18 Nm (13 lb-ft) of torque force. The axle vent and LH brake flexible hose will be removed after dislodging the brake flexible hose retaining clip. New installation requires torquing the new hose to 17 Nm (13 lb-ft). After reversing all brake flexible hose installation processes you must bleed the brake caliper for both RH and LH positions. Employ brake fluid which is clean and matches manufacturer requirements to keep the system free from contamination while being cautious of fluid effects on paint and plastic surfaces since immediate water cleaning removes spills. Contact 1-800-959-3673 to obtain emergency medical data about Ford/Motorcraft products while referring to the available product Material Safety Data Sheet (MSDS).

OEM Ford E-150 Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Brake Lines found

View related parts
Ford E-150 Flex Hose, Rear Driver Side Part Number: 8C2Z-2A442-C
$60.11 MSRP: $98.91
You Save: $38.80 (40%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hose Assembly; Brake Hydraulic Line, Rear Left; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear Driver Side
- Replaces: BRHR-79, 8C2Z-2A442-CL
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Flex Hose, Front Passenger Side Part Number: 8C2Z-2078-BR
$64.55 MSRP: $108.36
You Save: $43.81 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Front Right; Brake Hose; Brake Line; Hydraulic Hose
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Flex Hose, Front Driver Side Part Number: 8C2Z-2078-BL
$68.29 MSRP: $112.36
You Save: $44.07 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Front Left; Brake Hose; Brake Line; Hydraulic Hose
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Flex Hose, Passenger Side Part Number: CC2Z-2A442-A
$40.49 MSRP: $56.01
You Save: $15.52 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Flex Hose, Rear Passenger Side Part Number: AC2Z-2A442-B
$42.29 MSRP: $66.00
You Save: $23.71 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly; Brake Hydraulic Line, Rear Right; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear Passenger Side
- Replaces: 8C2Z-2A442-BR
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Flex Hose, Driver Side Part Number: CC2Z-2A442-D
$104.12 MSRP: $174.80
You Save: $70.68 (41%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Replaces: CC2Z-2A442-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Flex Hose, Driver Side Part Number: 6C2Z-2078-AB
$27.77 MSRP: $37.79
You Save: $10.02 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly - Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Replaces: 4C2Z-2078-AF
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford E-150 | Base, Chateau, XL, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Flex Hose, Passenger Side Part Number: 6C2Z-2078-AA
$40.99 MSRP: $56.71
You Save: $15.72 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly - Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Replaces: 4C2Z-2078-AE
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford E-150 | Base, Chateau, XL, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Flex Hose, Driver Side Part Number: 8C2Z-2A442-EL
Product Specifications
- Other Name: Hose Assembly; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Flex Hose, Passenger Side Part Number: 8C2Z-2A442-CR
Product Specifications
- Other Name: Hose Assembly; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2012 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Flex Hose, Driver Side Part Number: F4UZ-2078-F
Product Specifications
- Other Name: Hose Assembly - Brake; Hydraulic Hose; Brake Hose; Brake Line
- Manufacturer Note: LH, with rear wheel ABS
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford E-150 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Flex Hose, Passenger Side Part Number: F4UZ-2078-E
Product Specifications
- Other Name: Hose Assembly - Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford E-150 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Flex Hose, Driver Side Part Number: F4UZ-2078-D
Product Specifications
- Other Name: Hose Assembly - Brake; Hydraulic Hose; Brake Hose; Brake Line
- Manufacturer Note: LH, with 4 wheel ABS
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford E-150 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Flex Hose, Front Part Number: 6C2Z-2282-M
Product Specifications
- Other Name: Hose Assembly - Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front
- Replaces: 6C2Z-2282-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-150 | Base, Chateau, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS

Ford E-150 Brake Line

OEM Brake Line boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Line with long life and a perfect fit. Come to our website and find genuine Ford E-150 parts. We keep a wide inventory of OEM E-150 parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Brake Line plays an important in the hydraulic braking system which means that it is in charge of transferring brake fluid from the master cylinder to the brake caliper pistons safely and efficiently in Ford E-150 vehicles. Through its performance and durability, the Brake Line plays a crucial role that is flexible in different driving conditions; thus, it is installed in numerous E-150 models. Thus, the main importance of the Brake Line is not only in the performance improvement of the vehicle's braking system but also in the issue of safety on roads. They come in styles that include corrosion resistance stainless steel and braid up this ford e-150 brake line, has enhanced pedal feel and superior to the rubber hose because they tend to wear out in the long run. This upgrade is specifically useful for the drivers who are interested in improved and more reliable performance. Still, it is compatible with the Ford E-150 model, and its brake line will fit in any generation of E-150, so owners will have refined control over their brakes. Some of the great features of the Brake Line have also been highlighted to include some of the following This is because it is highly constructed; More to this, easy to install, To top it up, these features which the Brake Line enhances have highly placed it in the market to be among the most preferred by those who would want to improve on the brake line of their Ford E-150 vehicles above all.

Ford E-150 Brake Line Parts and Q&A

Flex Hose, Front Driver Side
8C2Z-2078-BL
Q: How to Service and Repair the Front Brake Line on Ford E-150?
A:
You should start servicing and fixing the front brake flexible hose after you detach its connection to the wheel speed sensor wiring harness. After removing the Brake Caliper flow bolt, users need to discard both copper washers but should replace them with new ones before reinstalling the bolt while tightening to 40 Nm of torque (30 lb-ft). The brake flexible hose must have its brake tube fitting disconnected before reinstallation where torques must reach 17 Nm (13 lb-ft). The brake flexible hose can be removed after disconnecting its retaining clip. The final step requires following the opposite steps of removal while performing a brake caliper bleeding procedure. Only factory-certified brake fluid which is clean and new can be used because the use of prior drain fluid creates risks of system pollution and damage to the system. The chemical nature of brake fluid causes damage to painted surfaces and plastic materials so promptly clean away any fluid accident with water. You can access emergency medical details about Ford and Motorcraft products by dialing 1-800-959-3673 from the United States or Canada along with available product Material Safety Data Sheets (MSDS).
Flex Hose, Rear Driver Side
8C2Z-2A442-C
Q: How to Service and Repair the Rear Brake Line Flexible Hoses on Ford E-150?
A:
The first step for servicing or repairing rear brake flexible hoses requires removal of the wheel and tire. You should remove the brake caliper flow bolt followed by discarding the two copper washers before tightening the new bolt to 40 Nm (30 lb-ft) during installation. When reinstalling disconnect the brake tube fitting from the LH brake flexible hose junction block with a torque of 18 Nm (13 lb-ft). The repair of the RH brake flexible hose follows brake tube servicing by removing the brake flexible hose bracket bolt and the RH brake flexible hose which needs to be fastened at 25 Nm (18 lb-ft) torque when replacing it. When installing the LH brake flexible hose then disconnect its brake tube fitting and make sure it reaches 18 Nm (13 lb-ft) of torque force. The axle vent and LH brake flexible hose will be removed after dislodging the brake flexible hose retaining clip. New installation requires torquing the new hose to 17 Nm (13 lb-ft). After reversing all brake flexible hose installation processes you must bleed the brake caliper for both RH and LH positions. Employ brake fluid which is clean and matches manufacturer requirements to keep the system free from contamination while being cautious of fluid effects on paint and plastic surfaces since immediate water cleaning removes spills. Contact 1-800-959-3673 to obtain emergency medical data about Ford/Motorcraft products while referring to the available product Material Safety Data Sheet (MSDS).