How to Bleed the Brake System After Installing a New ABS Control Module on Ford E-150 Econoline?

When bleeding the brake system after installing a new Four Wheel Anti-Lock Brake System (4WABS) Hydraulic Control Unit (HCU) or opening the HCU lines the process should start by cleaning all dirt from the brake master cylinder filler cap followed by filling the brake master cylinder reservoir with the specified brake fluid. A clear waste line needs installation on the RH rear bleeder screw with one end submerged in the recommended brake fluid solution contained inside a container. A technician should start the bleeder screw process by opening the RH rear until brake fluid streams from the valve while a helper applies pressure to the brake pedal before tightening the valve. Use the same procedure again until the fluid remains bubble-free while emptying the brake master cylinder reservoir when needed. To finish the bleeding process, first detach the waste line then follow the sequence of LH rear, RH front, and LH front bleeder screw procedures while flushing out the brake fluid through partially filled recommended brake fluid containers. You should connect the scan tool DCL cable adapter to the under-dash Data Link Connector (DLC) before following the scan tool instructions. The system bleed process should be performed according to earlier instructions.

How to Service the ABS Control Module on Ford E-150 Econoline?

One must start by detaching the HCU bracket and bolting it away before proceeding with Electronic Brake Control Module servicing. Start by removing the anti-lock brake control module after unscrewing it. Reverse the removal steps to install the anti-lock brake control module onto the HCU while reattaching its bracket.

OEM Ford E-150 Econoline ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 ABS Control Modules found

View related parts
Ford E-150 Econoline Control Valve Part Number: 7C2Z-2C219-CA
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 6C2Z-2C219-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford E-150 Econoline | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Econoline Modulator Valve Part Number: 6C2Z-2C286-CA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Replaces: 2C2Z-2C286-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford E-150 Econoline | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Econoline Modulator Valve Part Number: 6C2Z-2C286-BA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford E-150 Econoline | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Econoline Speed Sensor Part Number: 6L3Z-2B373-A
$774.00 MSRP: $1058.46
You Save: $284.46 (27%)
Product Specifications
- Other Name: Valve Assembly - Modulator; ABS Hydraulic Assembly; Control Valve; Control Module; Modulator Valve
- Replaces: XL3Z-2B373-BARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2002 Ford E-150 Econoline | Base, XL | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Econoline Control Module Part Number: XC2Z-2B373-AA
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2002 Ford E-150 Econoline | Base, XL | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Econoline Control Valve Part Number: 7C2Z-2C219-FA
Product Specifications
- Other Name: Control; ABS Control Module; Control Module
- Replaces: 6C2Z-2C219-FA, 6C2Z-2C219-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford E-150 Econoline | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Econoline Control Valve Part Number: 4C2Z-2C219-GARM
Product Specifications
- Other Name: Module - ABS Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Ford E-150 Econoline | Base, XL | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Econoline Control Module Part Number: 3L3Z-2C286-AARM
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2001 Ford E-150 Econoline | Base, XL | 6 Cyl 4.2 L GAS, 6 Cyl 4.9 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L GAS, 8 Cyl 5.8 L GAS
View related parts
Ford E-150 Econoline Modulator Valve Part Number: F8UZ-2C286-ARM
Product Specifications
- Other Name: Control Assembly - ABS Hydraulic; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit; Control Assembly - ABS Hydraulics
- Manufacturer Note: HCU, 4 wheel ABS
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1996 Ford E-150 Econoline | Base, XL | 6 Cyl 4.9 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS
View related parts
Ford E-150 Econoline Control Valve Part Number: F6UZ-2C219-CA
Product Specifications
- Other Name: Control; ABS Control Module; Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1996 Ford E-150 Econoline | Base, XL | 6 Cyl 4.9 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS
View related parts
Ford E-150 Econoline Control Valve Part Number: 3C2Z-2C286-AARM
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2002 Ford E-150 Econoline | Base, XL | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L GAS

Ford E-150 Econoline ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Ford E-150 Econoline parts. We keep a wide inventory of OEM E-150 Econoline parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford E-150 Econoline ABS Control Module Parts and Q&A

Speed Sensor
6L3Z-2B373-A
Q: How to Bleed the Brake System After Installing a New ABS Control Module on Ford E-150 Econoline?
A:
When bleeding the brake system after installing a new Four Wheel Anti-Lock Brake System (4WABS) Hydraulic Control Unit (HCU) or opening the HCU lines the process should start by cleaning all dirt from the Brake Master Cylinder filler cap followed by filling the brake master cylinder reservoir with the specified brake fluid. A clear waste line needs installation on the RH rear bleeder screw with one end submerged in the recommended brake fluid solution contained inside a container. A technician should start the bleeder screw process by opening the RH rear until brake fluid streams from the valve while a helper applies pressure to the brake pedal before tightening the valve. Use the same procedure again until the fluid remains bubble-free while emptying the brake master cylinder reservoir when needed. To finish the bleeding process, first detach the waste line then follow the sequence of LH rear, RH front, and LH front bleeder screw procedures while flushing out the brake fluid through partially filled recommended brake fluid containers. You should connect the scan tool DCL cable adapter to the under-dash Data Link Connector (DLC) before following the scan tool instructions. The system bleed process should be performed according to earlier instructions.
Control Valve
3C2Z-2C286-AARM
Q: How to Service the ABS Control Module on Ford E-150 Econoline?
A:
One must start by detaching the HCU bracket and bolting it away before proceeding with Electronic Brake Control Module servicing. Start by removing the anti-lock brake control module after unscrewing it. Reverse the removal steps to install the anti-lock brake control module onto the HCU while reattaching its bracket.