How to properly bench bleed the brake master cylinder on Ford Escape?

The correct procedure of bench bleeding the brake master cylinder demands using approved DOT 3 brake fluid since alternative types will result in permanent damage that makes the brakes dysfunctional which creates a danger of personal injury. Consult emergency medical support by contacting 1-800-959-3673 for Ford/Motorcraft products in the United States and Canada to obtain important information. Additionally read all cautions printed on the product label with attention. Bleeding the master cylinder of hybrid vehicles needs a complete system pressure bleed procedure. The brake master cylinder reservoir must be maintained with fresh specified brake fluid throughout the bleeding procedure to prevent dryness since you should always discard drained brake fluid. When managing brake fluid keep an eye out for damage to paints and plastics because quick water cleaning needs to remove any traces of fluid. Spongy brake pedal behavior occurs when air enters the hydraulic system following disconnect or new component installation of any hydraulic system part which requires subsequently bleeding the hydraulic system after proper reconnection. Start by suspending the master cylinder body in a soft vise then remove the cap and position short tubes into the outlet ports before submerging their ends into the fluid reservoir. For vehicles equipped with manual transmissions users should plug the opening in the master cylinder that serves as the feed port. Pour clean acceptable brake fluid into the reservoir while pressing the primary piston giving enough time for both hoses to show bubble-free brake fluid. The process ends with brake tube removal before putting plugs in all outlet ports while replacing the master cylinder cap before installing it into the vehicle although you should remove the plug from ports before tube assembly.

How to service and repair the brake master cylinder on Ford Escape?

Service and repair work on the brake master cylinder should start with disconnecting the electrical connector of the brake fluid level warning switch. A suitable suction device should be used to empty the brake master cylinder reservoir. Vehicle service requires disconnecting the clutch master cylinder feed whenever the transmission is manual. The first step includes disconnecting brake lines and using plugging methods to stop fluid leakage from both brake components. The removal of the brake master cylinder from the brake booster must be followed by installing new nuts. You should remove the brake master cylinder following the removal of its nuts. The new brake master cylinder reservoir requires seals which must be replaced and brake fluid must be used for lubrication. You must transfer the brake master cylinder reservoir during new master cylinder replacement before sealing it using clean brake fluid on the O-ring pairs and inserting them into the brake master cylinder. Press the brake master cylinder reservoir until it snaps into position when inserted into the O-ring seals. The installation process ends by following removal steps while bleeding the master cylinder and optionally bleeding the clutch master cylinder.

OEM Ford Escape Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Brake Master Cylinders found

View related parts
Ford Escape Master Cylinder Part Number: 9L8Z-2140-A
$147.65 MSRP: $242.95
You Save: $95.30 (40%)
ADD TO CART
Product Specifications
- Other Name: Kit - Master Cylinder Repair; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Master Cylinder Part Number: 8L8Z-2140-A
$137.16 MSRP: $230.91
You Save: $93.75 (41%)
ADD TO CART
Product Specifications
- Other Name: Kit - Master Cylinder Repair; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Master Cylinder Part Number: EV6Z-2140-A
$136.38 MSRP: $224.40
You Save: $88.02 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly - Master; Brake Master Cylinder
- Replaces: BRMC-158, BV6Z-2140-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Escape | S, SE, SEL, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Escape Master Cylinder Part Number: 9M6Z-2140-A
$155.63 MSRP: $262.00
You Save: $106.37 (41%)
ADD TO CART
Product Specifications
- Other Name: Kit - Master Cylinder Repair; Brake Master Cylinder
- Manufacturer Note: Service Kit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Ford Escape | Hybrid, Limited Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Escape Master Cylinder Part Number: 6L8Z-2140-C
$145.81 MSRP: $201.71
You Save: $55.90 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Master Cylinder Repair; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Master Cylinder Part Number: 6L8Z-2140-B
$95.13 MSRP: $129.46
You Save: $34.33 (27%)
ADD TO CART
Product Specifications
- Other Name: Kit - Master Cylinder; Brake Master Cylinder; Kit - Master Cylinder Repair
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Master Cylinder Part Number: 9L8Z-2140-C
$91.82 MSRP: $127.03
You Save: $35.21 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Master Cylinder Repair; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Master Cylinder Part Number: JX6Z-2140-K
$120.16 MSRP: $190.80
You Save: $70.64 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Master Cylinder Repair; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Escape | Active, Base, Platinum, Platinum Hybrid, Plug-In Hybrid, S, SE, SE Plug-In Hybrid, SE Sport Hybrid, SEL, SEL Plug-In Hybrid, ST-Line, ST-Line Elite, ST-Line Elite Hybrid, ST-Line Hybrid, ST-Line Select, ST-Line Select Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Master Cylinder Part Number: 8M6Z-2140-A
Product Specifications
- Other Name: Cylinder Assembly - Master; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford Escape | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Escape Master Cylinder Part Number: 5M6Z-2140-B
Product Specifications
- Other Name: Cylinder Assembly - Master; Brake Master Cylinder
- Replaces: 5M6Z-2140-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Escape | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Escape Master Cylinder Part Number: 8L8Z-2140-C
Product Specifications
- Other Name: Kit - Master Cylinder Repair; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Master Cylinder Part Number: 6L8Z-2140-D
Product Specifications
- Other Name: Kit - Master Cylinder; Brake Master Cylinder; Kit - Master Cylinder Repair
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Master Cylinder Part Number: 6L8Z-2140-A
Product Specifications
- Other Name: Kit - Master Cylinder Repair; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Master Cylinder Part Number: 2L8Z-2140-BA
Product Specifications
- Other Name: Cylinder Assembly - Master; Brake Master Cylinder
- Replaces: YL8Z-2140-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Master Cylinder Part Number: 2L8Z-2140-AA
Product Specifications
- Other Name: Cylinder Assembly - Master; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS

Ford Escape Brake Master Cylinder

OEM Brake Master Cylinder boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Master Cylinder with long life and a perfect fit. Come to our website and find genuine Ford Escape parts. We keep a wide inventory of OEM Escape parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The subject of the study is Brake Master Cylinder that is used in Ford Escape and performs essential role of translating the pressure applied by the driver through his foot pedal into hydraulic pressure. This mechanism works through a fluid being pumped through the system to contact the brake calipers or the drum brake as the case may be to generate the kind of friction that is required to bring the vehicle to a stop. Common fixed type of master cylinder incorporates two circuits with two pistons to make sure that at least one circuit would provide braking force when the other is failing to do so. For models of Ford Escape, housings may be manufactured from cast iron or aluminum and the fluid reservoir may be either integral or detached. The design variations are; this is in relation to the type of reservoir attachment and cap type, which impacts on often servicing and possible leakage areas. Common problems of the Brake Master Cylinder include fluid leakage problems, usually accompanied by internal problems such as moisture or rust, which requires immediate intervention in order to affect safe braking.

Ford Escape Brake Master Cylinder Parts and Q&A

Master Cylinder
8L8Z-2140-C
Q: How to properly bench bleed the brake master cylinder on Ford Escape?
A:
The correct procedure of bench bleeding the brake master cylinder demands using approved DOT 3 brake fluid since alternative types will result in permanent damage that makes the brakes dysfunctional which creates a danger of personal injury. Consult emergency medical support by contacting 1-800-959-3673 for Ford/Motorcraft products in the United States and Canada to obtain important information. Additionally read all cautions printed on the product label with attention. Bleeding the master cylinder of hybrid vehicles needs a complete system pressure bleed procedure. The brake master cylinder reservoir must be maintained with fresh specified brake fluid throughout the bleeding procedure to prevent dryness since you should always discard drained brake fluid. When managing brake fluid keep an eye out for damage to paints and plastics because quick water cleaning needs to remove any traces of fluid. Spongy brake pedal behavior occurs when air enters the hydraulic system following disconnect or new component installation of any hydraulic system part which requires subsequently bleeding the hydraulic system after proper reconnection. Start by suspending the master cylinder body in a soft vise then remove the cap and position short tubes into the outlet ports before submerging their ends into the fluid reservoir. For vehicles equipped with manual transmissions users should plug the opening in the master cylinder that serves as the feed port. Pour clean acceptable brake fluid into the reservoir while pressing the primary piston giving enough time for both hoses to show bubble-free brake fluid. The process ends with brake tube removal before putting plugs in all outlet ports while replacing the master cylinder cap before installing it into the vehicle although you should remove the plug from ports before tube assembly.
Master Cylinder
2L8Z-2140-BA
Q: How to service and repair the brake master cylinder on Ford Escape?
A:
Service and repair work on the brake master cylinder should start with disconnecting the electrical connector of the brake fluid level warning switch. A suitable suction device should be used to empty the Brake Master Cylinder Reservoir. Vehicle service requires disconnecting the Clutch Master Cylinder feed whenever the transmission is manual. The first step includes disconnecting Brake Lines and using plugging methods to stop fluid leakage from both brake components. The removal of the brake master cylinder from the Brake Booster must be followed by installing new nuts. You should remove the brake master cylinder following the removal of its nuts. The new brake master cylinder reservoir requires seals which must be replaced and brake fluid must be used for lubrication. You must transfer the brake master cylinder reservoir during new master cylinder replacement before sealing it using clean brake fluid on the O-ring pairs and inserting them into the brake master cylinder. Press the brake master cylinder reservoir until it snaps into position when inserted into the O-ring seals. The installation process ends by following removal steps while bleeding the master cylinder and optionally bleeding the clutch master cylinder.