How to Service and Repair the Lower Rear Motor and Transmission Mount for the 2.0L 4V on Ford Escape?

Service and repair operations on the transaxle support insulator-lower, rear for the 2.0L 4V require users to disconnect the battery cables followed by removing the battery tray. Start by disconnecting the breather tube followed by the mass air flow sensor then remove the intake tube alongside the air cleaner cover before taking out the air cleaner assembly. First remove the rack bolts and afterward remove bolts and nuts from the mount to take out the mount itself. You must begin the installation procedure by putting in new mount and bolts then gently fit the mount bolt to achieve correct alignment before applying torque to the nuts and bolt. Start by mounting the rack bolts after which you should arrange the air cleaner assembly and intake tube and air cleaner cover. Before final installation of the battery tray verify that the breather tube alongside the MAF sensor can function correctly with no constraints. Inspect the vent tube hose for any blockages or kinks that may obstruct its proper routing. Fitting the battery and tray in place marks the final step of the service followed by reconnecting battery cables. The adaptive strategy learning process for the vehicle requires 160 kilometers (100 miles) of driving or more after disconnecting and reconnecting battery cables before normal driving behavior resumes.

How to Service and Repair a Motor and Transmission Mount for the LH Transaxle Support Insulator on Ford Escape?

Service work on the LH transaxle support insulator begins only after setting the vehicle to neutral gear and hoisting it off the ground. The first step requires air cleaner removal before using the engine support bar to suspend the engine. The LH transaxle support insulator requires four bolts removal which should be tightened to 35 lb-ft when installation is complete. You should tighten both the through bolt and LH transaxle support insulator to 103 Nm (76 lb-ft) after removing them. As the last step remove the three nuts from the LH transaxle support insulator bracket before tightening each one to 40 Nm (30 lb-ft). Perform the opposite operations to finish your installation procedure.

OEM Ford Escape Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

98 Motor And Transmission Mounts found

View related parts
Ford Escape Transmission Mount, Rear Part Number: 5L8Z-6038-AA
$45.87 MSRP: $65.62
You Save: $19.75 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Support; Manual/Auto Trans Mount; Mount Torque Strut & Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Bracket Insulator
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2012 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Mount Part Number: 3L8Z-6038-EA
$67.99 MSRP: $94.05
You Save: $26.06 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Manual Transmission Mount; Engine Mount Bracket; Motor Mount; Transmission Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Escape | Limited, XLS, XLT | 6 Cyl 3.0 L GAS
View related parts
Ford Escape Engine Support Part Number: 5L8Z-6P094-AA
$70.41 MSRP: $97.40
You Save: $26.99 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Support - Engine Mounting - Front; Engine Mount Crossmember; Motor Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Ford Escape | XLS, XLT, XLT No Boundaries | 4 Cyl 2.3 L GAS
View related parts
Ford Escape Transmission Mount Part Number: YL8Z-6038-AA
$50.06 MSRP: $69.25
You Save: $19.19 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Manual Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Front Mount; Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Front Mount Part Number: BV6Z-6038-B
$120.29 MSRP: $175.10
You Save: $54.81 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Motor Mount; Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Escape | SE, SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Side Mount, Rear Part Number: 9L8Z-6068-A
$85.90 MSRP: $125.03
You Save: $39.13 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount, Rear; Engine Mount Bracket; Motor Mount; Rear Mount; Mount
- Position: Rear
- Replaces: 5L8Z-6068-BB, 5L8Z-6068-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2012 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Front Mount Part Number: YL8Z-6068-AA
$150.00 MSRP: $218.33
You Save: $68.33 (32%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount Support Bracket; Torque Strut; Motor Mount; Rear Mount; Front Insulator; Insulator
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2006 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Engine Support Part Number: 9L8Z-6P094-C
$99.25 MSRP: $144.47
You Save: $45.22 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Support - Engine Mounting - Front; Engine Mount Crossmember; Motor Mount
- Replaces: 9L8Z-6P094-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Transmission Mount Part Number: NZ6Z-6068-B
$130.99 MSRP: $190.67
You Save: $59.68 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing - Transmission Extension; Automatic Transmission Mount; Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2023 Ford Escape | Platinum, ST-Line Elite, ST-Line Select | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Rear Mount Part Number: 9M6Z-6A023-A
$78.60 MSRP: $106.95
You Save: $28.35 (27%)
ADD TO CART
Product Specifications
- Other Name: Support; Engine Mount Bracket; Engine Mount Torque Strut; Motor Mount; Side Support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2012 Ford Escape | Hybrid, Limited Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Escape Motor Mount Part Number: LX6Z-6038-D
$172.90 MSRP: $251.67
You Save: $78.77 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Side Mount; Front Mount
- Replaced by: LX6Z-6038-Z
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Escape | Platinum Hybrid, Plug-In Hybrid, SE Hybrid, SE Plug-In Hybrid, SE Sport Hybrid, SEL Hybrid, SEL Plug-In Hybrid, ST-Line Elite Hybrid, ST-Line Hybrid, ST-Line Select Hybrid, Titanium Hybrid, Titanium Plug-In Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Transmission Mount Part Number: 5L8Z-6038-CA
$48.08 MSRP: $66.51
You Save: $18.43 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Manual Transmission Mount; Transfer Case Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2012 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Escape Support Rod Part Number: 5M6Z-6068-AC
$35.38 MSRP: $48.14
You Save: $12.76 (27%)
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Support Rod; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Link Rod; Support Strut; Strut
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2012 Ford Escape | Hybrid, Limited Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Escape Mount Part Number: PZ1Z-6068-C
$96.10 MSRP: $139.88
You Save: $43.78 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2023 Ford Escape | Platinum, ST-Line Elite, ST-Line Select | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Transmission Mount Part Number: LX6Z-6068-AC
$127.21 MSRP: $185.17
You Save: $57.96 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing - Transmission Extension
- Replaced by: PZ1Z-6068-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford Escape | Active, Base, S, SE, SEL, ST-Line | 3 Cyl 1.5 L GAS
View related parts
Ford Escape Front Mount Part Number: LX6Z-6038-E
$142.32 MSRP: $207.17
You Save: $64.85 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Motor Mount
- Replaced by: LX6Z-6038-Y
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Escape | Platinum Hybrid, Plug-In Hybrid, SE Hybrid, SE Plug-In Hybrid, SE Sport Hybrid, SEL Hybrid, SEL Plug-In Hybrid, ST-Line Elite Hybrid, ST-Line Hybrid, ST-Line Select Hybrid, Titanium Hybrid, Titanium Plug-In Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Front Mount Part Number: LX6Z-6038-U
$137.29 MSRP: $199.83
You Save: $62.54 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford Escape | Active, Base, S, SE, SEL, ST-Line | 3 Cyl 1.5 L GAS
View related parts
Ford Escape Front Mount Part Number: PZ1Z-6038-B
$130.99 MSRP: $190.67
You Save: $59.68 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2023 Ford Escape | Active, Base, ST-Line | 3 Cyl 1.5 L GAS
View related parts
Ford Escape Torque Arm Part Number: LX6Z-6068-AF
$99.71 MSRP: $153.45
You Save: $53.74 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Mount
- Replaces: LX6Z-6068-AA, LX6Z-6068-E, LX6Z-6068-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Escape | Platinum, Platinum Hybrid, Plug-In Hybrid, SE Hybrid, SE Plug-In Hybrid, SE Sport Hybrid, SEL, SEL Hybrid, SEL Plug-In Hybrid, ST-Line Elite, ST-Line Elite Hybrid, ST-Line Hybrid, ST-Line Select, ST-Line Select Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Mount Part Number: PZ1Z-6038-C
$130.99 MSRP: $190.67
You Save: $59.68 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2023 Ford Escape | Platinum, ST-Line Elite, ST-Line Select | 4 Cyl 2.0 L GAS

| Page 1 of 5 |Next >

1-20 of 98 Results

Ford Escape Motor And Transmission Mount

OEM Motor And Transmission Mount boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Motor And Transmission Mount with long life and a perfect fit. Come to our website and find genuine Ford Escape parts. We keep a wide inventory of OEM Escape parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Motor And Transmission Mount on Ford Escape cars is very essential part that offers holding ability of the transmission and also addresses it protection from vibrations coming from the engine. This part is crucial for us to have a stable and efficient ride of the vehicle. Depending on how and what type of Transmission is installed in the Ford Escape, there may be one or several products with the label 'Motor And Transmission Mounts'. Different types of Motor And Transmission Mounts have been used in Ford Escape vehicle throughout the years, and each of them is specifically meant to deal with the transmission, positioning, and to counter vibrations. The differences may include differences in the design of the types of these tires and the number of mounts used, which may have an impact on the overall performance as well as comfort of the vehicle. Altogether, the Motor And Transmission Mount is a pretty important element in Ford Escape's operation and handling.

Ford Escape Motor And Transmission Mount Parts and Q&A

Rear Mount
YL8Z-6068-BA
Q: How to Service and Repair the Lower Rear Motor and Transmission Mount for the 2.0L 4V on Ford Escape?
A:
Service and repair operations on the transaxle support insulator-lower, rear for the 2.0L 4V require users to disconnect the battery cables followed by removing the battery tray. Start by disconnecting the breather tube followed by the Mass Air Flow Sensor then remove the intake tube alongside the air cleaner cover before taking out the air cleaner assembly. First remove the rack bolts and afterward remove bolts and nuts from the mount to take out the mount itself. You must begin the installation procedure by putting in new mount and bolts then gently fit the mount bolt to achieve correct alignment before applying torque to the nuts and bolt. Start by mounting the rack bolts after which you should arrange the air cleaner assembly and intake tube and air cleaner cover. Before final installation of the battery tray verify that the breather tube alongside the MAF sensor can function correctly with no constraints. Inspect the vent tube hose for any blockages or kinks that may obstruct its proper routing. Fitting the battery and tray in place marks the final step of the service followed by reconnecting battery cables. The adaptive strategy learning process for the vehicle requires 160 kilometers (100 miles) of driving or more after disconnecting and reconnecting battery cables before normal driving behavior resumes.
Rear Mount
9M6Z-6068-A
Q: How to Service and Repair a Motor and Transmission Mount for the LH Transaxle Support Insulator on Ford Escape?
A:
Service work on the LH transaxle support insulator begins only after setting the vehicle to neutral gear and hoisting it off the ground. The first step requires air cleaner removal before using the engine support bar to suspend the engine. The LH transaxle support insulator requires four bolts removal which should be tightened to 35 lb-ft when installation is complete. You should tighten both the through bolt and LH transaxle support insulator to 103 Nm (76 lb-ft) after removing them. As the last step remove the three nuts from the LH transaxle support insulator bracket before tightening each one to 40 Nm (30 lb-ft). Perform the opposite operations to finish your installation procedure.