How to service and repair the engine mount on Ford Explorer Sport Trac?

Service procedures for engine mount repair should start by removing the fan shroud first. Beginning with the left-hand (LH) engine insulator nuts you must then remove the right-hand (RH) engine insulator nuts. Post the vehicle to lift height and make sure to anchor the axle housing of 4x4 vehicles onto appropriate supports. Keep the front axle bolts loose without disconnecting them while moving the lift to expose the left motor mount nut. Proceed with nut removal from the LH and RH engine support insulators followed by suspending the engine before pulling out the insulators. The installation requires following the reverse steps of removal to finish the process.

How to remove and replace the engine mount on Ford Explorer Sport Trac?

A hoist positioned vehicle requires neutral gear position and disconnecting battery cables for the start of engine mount removal and replacement. The installation requires removing the weather strip and bolt to set aside the power steering fluid reservoir then tightening everything to 7 Nm (62 lb-in) before completing reinstallation. Let your engine temperature decrease first before taking off the coolant expansion tank to stop air from entering the radiator while you disconnect the overflow hose and tighten its supporting bolts to 7 Nm (62 lb-in). The next step requires the removal of two bolts accompanied by unclipping the clips to extract the upper fan shroud before reinstalling with screws tightened to 7 Nm (62 lb-in). The Engine Lifting Bracket requires 42 Nm (31 lb-ft) tightening for its bolt before adding the Engine Support Bar while also installing the pair of Adapters for 303-290A. The LH engine mount requires removal via its bolt which needs tightening to 103 Nm (76 lb-ft) before reinstalling. After that disconnect the five pushpins and the RH inner fender splash shield. Replace the RH engine mount by first loosening the three nuts to 90 Nm (66 lb-ft) torque then raising the engine by 60 mm (2.36 in). AWD models need four bolts removal and two stabilizer bar brackets extraction to suspend the bar until setting torque to 55 Nm (41 lb-ft) at reassembly. Hang the assembly from a jack which should be set away from obstacles before performing any lower or upper motions and use a proper jack to stabilize the axle housing. Disconnect the axle housing vent tube and remove three bolts along with three flag nuts then lower the housing 25 mm (1 in) and retighten bolts to 66 Nm (49 lb-ft). To finish the installation normalize the reinstallation of the LH engine mount nut while tightening it to 90 Nm (66 lb-ft) and proceed with the removal procedure in reverse order.

OEM Ford Explorer Sport Trac Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Engine Mounts found

View related parts
Ford Explorer Sport Trac Motor Mount, Driver Side Part Number: 7A2Z-6038-CA
$74.11 MSRP: $91.67
You Save: $17.56 (20%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount, Left; Engine Mount Bracket; Front Mount
- Position: Driver Side
- Replaces: 7A2Z-6038-C, 7A2Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Explorer Sport Trac | Limited, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Sport Trac Motor Mount Bracket, Driver Side Part Number: 7A2Z-6031-AA
$17.30 MSRP: $23.54
You Save: $6.24 (27%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Engine Mount Bracket, Left; Motor Mount; Bracket; Engine Mount Bracket
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Explorer Sport Trac | Limited, XLT | 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Sport Trac Motor Mount, Passenger Side Part Number: 7A2Z-6038-D
$70.30 MSRP: $102.33
You Save: $32.03 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Right; Engine Mount Bracket; Front Mount; Engine Mount
- Position: Passenger Side
- Replaces: 5L2Z-6038-AD, 7A2Z-6038-B, 5L2Z-6038-BB, 5L2Z-6038-AB, 6L2Z-6038-AB, 5L2Z-6038-BD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Explorer Sport Trac | Limited, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Sport Trac Motor Mount, Driver Side Part Number: 6L2Z-6031-BA
$28.44 MSRP: $39.34
You Save: $10.90 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Engine Mount Bracket, Left; Engine Mount, Left; Motor Mount Bracket; Front Mount; Bracket; Engine Mount Bracket
- Position: Driver Side
- Replaces: 7A2Z-6031-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Explorer Sport Trac | Limited, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Explorer Sport Trac Mount Bracket, Driver Side Part Number: F87Z-6031-FA
$59.45 MSRP: $86.53
You Save: $27.08 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Engine Mount Bracket, Left; Motor Mount; Motor Mount Bracket; Engine Mount Bracket
- Position: Driver Side
- Replaces: F77Z-6031-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2005 Ford Explorer Sport Trac | Adrenalin, Base, XL, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS
View related parts
Ford Explorer Sport Trac Transmission Mount Part Number: 9L2Z-6068-A
$82.77 MSRP: $114.51
You Save: $31.74 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount.; Rear Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2010 Ford Explorer Sport Trac | Limited, XLT | 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Sport Trac Transmission Mount Part Number: 8L2Z-6068-B
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Transmission Mounts; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount
- Replaces: 6L2Z-6068-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Explorer Sport Trac | Limited, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Explorer Sport Trac Transmission Mount Part Number: F87Z-6068-KA
Product Specifications
- Other Name: Insulator Assembly - Engine; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Insulator Assembly - Engine Support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2005 Ford Explorer Sport Trac | Adrenalin, Base, XL, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS
View related parts
Ford Explorer Sport Trac Transmission Mount Part Number: F5TZ-6068-A
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Manual Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Insulator
- Replaces: E5TZ-6068-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2005 Ford Explorer Sport Trac | Adrenalin, Base, XL, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS
View related parts
Ford Explorer Sport Trac Motor Mount Bracket, Passenger Side Part Number: 6L2Z-6030-AA
Product Specifications
- Other Name: Bracket; Engine Mount Bracket, Right; Motor Mount; Engine Mount Bracket
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Explorer Sport Trac | Limited, XLT | 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Sport Trac Motor Mount, Passenger Side Part Number: 3L2Z-6038-BB
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Right; Engine Mount Bracket; Front Mount; Engine Mount
- Position: Passenger Side
- Replaces: F5TZ-6038-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2005 Ford Explorer Sport Trac | Adrenalin, Base, XL, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS
View related parts
Ford Explorer Sport Trac Motor Mount, Driver Side Part Number: 3L2Z-6038-BA
Product Specifications
- Other Name: Insulator Assembly - Engine; Engine Mount, Left; Engine Mount Bracket; Front Mount; Insulator Assembly - Engine Support
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2005 Ford Explorer Sport Trac | Adrenalin, Base, XL, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS
View related parts
Ford Explorer Sport Trac Transmission Mount Part Number: 8L2Z-6068-A
$33.37 MSRP: $47.33
You Save: $13.96 (30%)
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount.; Rear Mount
- Replaces: 7A2Z-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Explorer Sport Trac | Limited, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Sport Trac Transmission Mount Part Number: 8L2Z-6068-C
Product Specifications
- Other Name: Insulator Assembly - Engine; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Insulator Assembly - Engine Support
- Replaces: 6L2Z-6068-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Explorer Sport Trac | Limited, XLT | 8 Cyl 4.6 L GAS

Ford Explorer Sport Trac Engine Mount

OEM Engine Mount boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Engine Mount with long life and a perfect fit. Come to our website and find genuine Ford Explorer Sport Trac parts. We keep a wide inventory of OEM Explorer Sport Trac parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Explorer Sport Trac Engine Mount Parts and Q&A

Mount Bracket, Driver Side
F87Z-6031-FA
Q: How to service and repair the engine mount on Ford Explorer Sport Trac?
A:
Service procedures for engine mount repair should start by removing the Fan Shroud first. Beginning with the left-hand (LH) engine insulator nuts you must then remove the right-hand (RH) engine insulator nuts. Post the vehicle to lift height and make sure to anchor the axle housing of 4x4 vehicles onto appropriate supports. Keep the front axle bolts loose without disconnecting them while moving the lift to expose the left motor mount nut. Proceed with nut removal from the LH and RH engine support insulators followed by suspending the engine before pulling out the insulators. The installation requires following the reverse steps of removal to finish the process.
Motor Mount, Passenger Side
7A2Z-6038-D
Q: How to remove and replace the engine mount on Ford Explorer Sport Trac?
A:
A hoist positioned vehicle requires neutral gear position and disconnecting Battery Cables for the start of engine mount removal and replacement. The installation requires removing the weather strip and bolt to set aside the power steering fluid reservoir then tightening everything to 7 Nm (62 lb-in) before completing reinstallation. Let your engine temperature decrease first before taking off the coolant expansion tank to stop air from entering the Radiator while you disconnect the overflow hose and tighten its supporting bolts to 7 Nm (62 lb-in). The next step requires the removal of two bolts accompanied by unclipping the clips to extract the upper Fan Shroud before reinstalling with screws tightened to 7 Nm (62 lb-in). The Engine Lifting Bracket requires 42 Nm (31 lb-ft) tightening for its bolt before adding the Engine Support Bar while also installing the pair of Adapters for 303-290A. The LH engine mount requires removal via its bolt which needs tightening to 103 Nm (76 lb-ft) before reinstalling. After that disconnect the five pushpins and the RH inner fender splash shield. Replace the RH engine mount by first loosening the three nuts to 90 Nm (66 lb-ft) torque then raising the engine by 60 mm (2.36 in). AWD models need four bolts removal and two stabilizer bar brackets extraction to suspend the bar until setting torque to 55 Nm (41 lb-ft) at reassembly. Hang the assembly from a jack which should be set away from obstacles before performing any lower or upper motions and use a proper jack to stabilize the axle housing. Disconnect the axle housing vent tube and remove three bolts along with three flag nuts then lower the housing 25 mm (1 in) and retighten bolts to 66 Nm (49 lb-ft). To finish the installation normalize the reinstallation of the LH engine mount nut while tightening it to 90 Nm (66 lb-ft) and proceed with the removal procedure in reverse order.