How to service and repair the intake manifold on Ford F-350 Super Duty?

Start servicing or repairing the intake manifold only when there is no presence of smoking or open flames because fuel-related components possess flammable properties. The service process requires draining fuel system pressure before unfastening fuel lines. First disconnect the fuel supply coupling from the fuel rail by removing its spring lock before draining the cooling system then extracting the generator. You should first remove the air cleaner outlet pipe and disconnect the upper radiator hose from the thermostat housing before disconnecting the heater coolant hose from the coolant crossover assembly. The service should begin by disconnecting the fuel rail pressure and temperature sensor electrical connector together with its vacuum connector while also separating the 10 fuel injector electrical connectors and intake manifold runner control (IMRC) actuator electrical connector. Disconnections are required for the positive crankcase ventilation (PCV) tube quick connect coupling from the intake manifold as well as the evaporative emissions (EVAP) tube quick connect couplings and the brake booster and engine vacuum hose connections from the rear of the intake manifold and the 2 heated PCV coolant hoses. Cut the right connections for throttle position (TP) and electronic throttle control after disconnecting both cables then remove the engine wiring harness position retainers found on top of the intake manifold. The installation of new intake manifold gaskets requires first removing all 12 bolts and afterwards cleaning the sealing surface using a silicone gasket remover and plastic scraping tool before discarding old gaskets. Install the intake manifold with new gaskets first and then position the coolant crossover tube with new gaskets before fastening its two bolts to 10 Nm (89 inch lbs.). The maintenance team should install intake manifold bolts through two steps starting at 2 Nm (18 inch lbs.) then tightening them to 10 Nm (89 inch lbs.). The service procedure requires the TP sensor and electronic throttle control electrical connectors to be reconnected with the engine wiring harness position retainers and PCV tube quick connect coupling while including brake booster and engine vacuum hose connections and EVAP tube quick connect couplings and 2 heated PCV coolant hoses. The installation process involves reattaching the 10 fuel injector electrical connectors as well as reconnecting the fuel rail pressure and temperature sensor electrical connector and vacuum connector and the IMRC actuator electrical connector. The final step includes connecting the fuel supply spring lock coupling to the fuel rail while also attaching the heater coolant hose to the coolant crossover assembly as well as mating the heated PCV coolant hose with the coolant crossover assembly and securing the upper radiator hose to the thermostat housing. Safely reattach the generator along with the air cleaner outlet pipe before processing engine cooling system filling and bleeding procedures.

OEM Ford F-350 Super Duty Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

32 Intake Manifolds found

View related parts
Ford F-350 Super Duty Intake Manifold, Upper Part Number: 2C3Z-9424-BA
$520.97 MSRP: $765.00
You Save: $244.03 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper; Upper Manifold
- Manufacturer Note: Upper. includes heater inlet tube xl1z-18599-aa
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford F-350 Super Duty | Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: 9L3Z-9424-H
$291.04 MSRP: $453.33
You Save: $162.29 (36%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold
- Replaces: 9L3Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2010 Ford F-350 Super Duty | Cabela's, FX4, King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: 5C3Z-9424-CRM
$1188.30 MSRP: $1783.33
You Save: $595.03 (34%)
ADD TO CART
Product Specifications
- Other Name: Remanufactured Kit - Manifold Hardware; Engine Intake Manifold; Lower Manifold
- Replaces: 5C3Z-9424-C, 5C3Z-9424-B, 5C3Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford F-350 Super Duty | Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: HC3Z-9424-J
$599.63 MSRP: $888.33
You Save: $288.70 (33%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019 Ford F-350 Super Duty | King Ranch, Lariat, Platinum, XL, XLT | 8 Cyl 6.2 L FLEX
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: HC3Z-9424-A
$419.95 MSRP: $616.67
You Save: $196.72 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Replaces: 5C3Z-9424-CA, BC3Z-9424-A, 8C3Z-9424-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010 Ford F-350 Super Duty | Cabela's, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
Ford F-350 Super Duty Intake Manifold, Upper Part Number: 9C2Z-9424-A
$2965.50 MSRP: $4393.33
You Save: $1427.83 (33%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper; Upper Manifold
- Position: Upper
- Replaces: YC2Z-9424-BA, 2C3Z-9424-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2002 Ford F-350 Super Duty | Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
Ford F-350 Super Duty Lower Manifold Part Number: 5C3Z-9424-CA
$419.95 MSRP: $616.67
You Save: $196.72 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet; Intake Manifold; Upper Manifold
- Replaced by: HC3Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford F-350 Super Duty | Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: HC3Z-9424-K
$664.88 MSRP: $985.00
You Save: $320.12 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019 Ford F-350 Super Duty | King Ranch, Lariat, Platinum, XL, XLT | 8 Cyl 6.2 L FLEX
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: PC3Z-9424-B
$120.23 MSRP: $175.00
You Save: $54.77 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2023-2024 Ford F-350 Super Duty | King Ranch, Lariat, Platinum, XL, XLT | 8 Cyl 6.8 L GAS, 8 Cyl 7.3 L GAS
View related parts
Ford F-350 Super Duty Intake Manifold, Upper Part Number: GC4Z-9424-A
$86.10 MSRP: $125.33
You Save: $39.23 (32%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper
- Position: Upper
- Replaces: BC3Z-9424-BE, BC3Z-9424-F, BC3Z-9424-B, BC3Z-9424-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2019 Ford F-350 Super Duty | King Ranch, Lariat, Limited, Platinum, XL, XLT | 8 Cyl 6.7 L DIESEL
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: 4C2Z-9424-CA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Lower Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford F-350 Super Duty | King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: 5L1Z-9424-A
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold; Lower Manifold
- Replaces: 5L1Z-9424-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford F-350 Super Duty | FX4, King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: 8C3Z-9424-A
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2010 Ford F-350 Super Duty | Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
Ford F-350 Super Duty Lower Manifold Part Number: 3C3Z-9424-AJ
Product Specifications
- Other Name: Kit - Manifold Hardware; Intake Manifold
- Manufacturer Note: KIT INTAKE MANIFOLD
- Replaces: 3C3Z-9424-AE, 3C3Z-9424-AH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford F-350 Super Duty | Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
Ford F-350 Super Duty Lower Manifold Part Number: 4C3Z-9424-E
Product Specifications
- Other Name: Kit - Manifold Hardware; Intake Manifold
- Replaces: 4C3Z-9424-C, 4C3Z-9424-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford F-350 Super Duty | Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: AL3Z-9424-E
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2016 Ford F-350 Super Duty | King Ranch, Lariat, Platinum, XL, XLT | 8 Cyl 6.2 L FLEX
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: AL3Z-9424-F
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2016 Ford F-350 Super Duty | King Ranch, Lariat, Platinum, XL, XLT | 8 Cyl 6.2 L FLEX
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: F75Z-9424-AB
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold; Lower Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999 Ford F-350 Super Duty | Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
Ford F-350 Super Duty Lower Manifold Part Number: F81Z9424AA
Product Specifications
- Other Name: Manifold Assembly Inlet; Intake Manifold; Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999 Ford F-350 Super Duty | Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
Ford F-350 Super Duty Intake Manifold Part Number: F85Z-9424-BA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Upper Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999 Ford F-350 Super Duty | Lariat, XL, XLT | 8 Cyl 5.4 L GAS

| Page 1 of 2 |Next >

1-20 of 32 Results

Ford F-350 Super Duty Intake Manifold

OEM Intake Manifold boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Intake Manifold with long life and a perfect fit. Come to our website and find genuine Ford F-350 Super Duty parts. We keep a wide inventory of OEM F-350 Super Duty parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Ford F-350 Super Duty intake manifold is flexible yet a very essential part that is well recognized for its dependability and output in the functionality of the engine. Responsible for supplying the air or the air/fuel mixture to the cylinder head intake port, Intake Manifold plays an important role to the Horsepower output of the Ford F-350 Super Duty from different models. However, with the passage of time, particularly due to the incorporation of high tech features in the vessels, the present Ford F-350 Super Duty Intake Manifolds are made of lightweight composite plastic to save fuel and for improving the efficiency of cooling. By implementing VLIM, the length of the intake tract is variable, and hence increases power and also fuel efficiency. This feature is even more important for the Ford F-350 Super Duty that has gone through four generations since the model's launch in 1999 and is available with a range of engines, including the mighty PowerStroke diesel. There are bottleneck standalone requisites for the Intake Manifold such as the coolant passages and temperature sensors on the design to allow complete airflow and pressure regulation. Moreover, the Ford F-350 Super Duty includes other important safety features as the antilock brake system coupled with the stability control that, along with the Intake Manifold, acts to boost the performance of the vehicles. The Ford F-350 Super Duty Intake Manifold is a known reminder in the automotive market for its uniqueness and its compatibility to various engines; this is why intake manifold is considered as a building block of the Ford F-350 Super Duty's reliability and fuel efficiency.

Ford F-350 Super Duty Intake Manifold Parts and Q&A

Intake Manifold
5C3Z-9424-CRM
Q: How to service and repair the intake manifold on Ford F-350 Super Duty?
A:
Start servicing or repairing the intake manifold only when there is no presence of smoking or open flames because fuel-related components possess flammable properties. The service process requires draining fuel system pressure before unfastening fuel lines. First disconnect the fuel supply coupling from the Fuel Rail by removing its spring lock before draining the cooling system then extracting the generator. You should first remove the air cleaner outlet pipe and disconnect the upper radiator hose from the Thermostat Housing before disconnecting the heater coolant hose from the coolant crossover assembly. The service should begin by disconnecting the fuel rail pressure and temperature sensor electrical connector together with its vacuum connector while also separating the 10 Fuel Injector electrical connectors and intake manifold runner control (IMRC) actuator electrical connector. Disconnections are required for the positive crankcase ventilation (PCV) tube quick connect coupling from the intake manifold as well as the evaporative emissions (EVAP) tube quick connect couplings and the Brake Booster and engine vacuum hose connections from the rear of the intake manifold and the 2 heated PCV coolant hoses. Cut the right connections for throttle position (TP) and electronic throttle control after disconnecting both cables then remove the engine wiring harness position retainers found on top of the intake manifold. The installation of new intake manifold gaskets requires first removing all 12 bolts and afterwards cleaning the sealing surface using a silicone gasket remover and plastic scraping tool before discarding old gaskets. Install the intake manifold with new gaskets first and then position the coolant crossover tube with new gaskets before fastening its two bolts to 10 Nm (89 inch lbs.). The maintenance team should install intake manifold bolts through two steps starting at 2 Nm (18 inch lbs.) then tightening them to 10 Nm (89 inch lbs.). The service procedure requires the TP sensor and electronic throttle control electrical connectors to be reconnected with the engine wiring harness position retainers and PCV tube quick connect coupling while including brake booster and engine vacuum hose connections and EVAP tube quick connect couplings and 2 heated PCV coolant hoses. The installation process involves reattaching the 10 fuel injector electrical connectors as well as reconnecting the fuel rail pressure and temperature sensor electrical connector and vacuum connector and the IMRC actuator electrical connector. The final step includes connecting the fuel supply spring lock coupling to the fuel rail while also attaching the heater coolant hose to the coolant crossover assembly as well as mating the heated PCV coolant hose with the coolant crossover assembly and securing the upper radiator hose to the thermostat housing. Safely reattach the generator along with the air cleaner outlet pipe before processing engine cooling system filling and bleeding procedures.