How to service the Engine Control Module on Ford Ranger?

The first step to serve the Engine Control Module begins with disconnecting the battery ground cable. Beginning service on the Engine Control Module requires unfastening the powertrain control module (PCM) wiring harness retainer nut while deliberately tightening it to 10 Nm (89 lb-in) torque after reinstallation. When disconnecting the PCM electrical connector you need to tighten it to 7 Nm (62 lb-in) after everything is back in place. Dispose of the stud bolt and place the ground cable and PCM wiring harness aside before tightening both to 10 Nm (89 lb-in). The installation should begin by removing two nuts and the PCM cover while applying 7 Nm (62 lb-in) torque for both. Reposition the PCM before you substitute it with the opposite order used during removal.

How to remove and replace the Engine Control Module on Ford Ranger?

Starting the Engine Control Module removal process demands a retrieval of module configuration data following the Programmable Module Installation procedure. The first step is to remove the PCM wiring harness retainer nut followed by the ground wire stud bolt while disconnecting the three PCM electrical connectors. Undertake the removal of both nuts securing the PCM unit before extracting the module from the system. After placing the PCM into its correct position you must fasten it using the two nuts which require a 10 Nm (89 lb-in) torque setting. Fasten the ground wire terminals by installing the stud bolt while tightening it to 10 Nm (89 lb-in). Secure the PCM wiring harness retainer nut by tightening it to 10 Nm (89 lb-in). When installing a new PCM it becomes necessary to reset the parameters inside both the PCM and instrument cluster module to prevent PATS no-start conditions that might affect un-PATS equipped vehicles. The restoration of module configurations for the instrument cluster module and PCM will follow the directions present in the Programmable Module Installation procedure.

OEM Ford Ranger Engine Control Module

Engine Control Computer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

98 Engine Control Modules found

View related parts
Ford Ranger Control Module Part Number: DU2Z-12A297-A
$60.00 MSRP: $98.73
You Save: $38.73 (40%)
ADD TO CART
Product Specifications
- Other Name: Module - Ignition; Ignition Control Module; Ignition Module; Computer; ECM
- Replaces: 5U2Z-12A297-A, E43Z-12A297-A, 5U2Z-12A297-C, E6SZ-12A297-A, DY-1074, DY-1076
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1992 Ford Ranger | Base, Custom, GT, S, Sport, STX, XL, XLS, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.3 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 2.9 L GAS
View related parts
Ford Ranger ECM Part Number: 1U7Z-12A650-FNA
$132.92 MSRP: $183.89
You Save: $50.97 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: 1L5Z-12A650-BCC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger ECM, Black Oak Part Number: 3U7Z-12A650-BCA
$132.92 MSRP: $183.89
You Save: $50.97 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Pcm - Black Oak; Engine Control Module (ECM); Engine Control Module
- Replaces: 3L5Z-12A650-AEB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Ranger | Edge, Tremor, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger ECM Part Number: F87Z-12A650-UB
$276.94 MSRP: $406.67
You Save: $129.73 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Manufacturer Note: Powertrain Control Module (PCM) #F87F 12A650-UB (EEC-V) TYPE:ML2-512 (REPROGRAMMABLE)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Ford Ranger | Splash, XL, XLT | 4 Cyl 2.5 L GAS
View related parts
Ford Ranger ECM Part Number: 7L5Z-12A650-AVG
$572.63 MSRP: $848.33
You Save: $275.70 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Ranger | Sport, STX, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger ECM, Black Oak Part Number: 3U7Z-12A650-BAA
$179.30 MSRP: $248.05
You Save: $68.75 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Pcm - Black Oak; Engine Control Module (ECM); Engine Control Module
- Replaces: 3L5Z-12A650-ACB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Ranger | Edge, Tremor, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger ECM Part Number: F8PZ-12A650-ETA
$174.48 MSRP: $241.38
You Save: $66.90 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: F87Z-12A650-AAB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-1999 Ford Ranger | Splash, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger ECM Part Number: 5U7Z-12A650-SA
$524.93 MSRP: $717.33
You Save: $192.40 (27%)
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: 5L5Z-12A650-AGA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Ford Ranger | Edge, FX4, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger ECM Part Number: F87Z-12A650-AMC
$282.49 MSRP: $384.69
You Save: $102.20 (27%)
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control; Engine Control Module (ECM); Engine Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Ranger | Edge, Splash, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger ECM Part Number: 7L5Z-12A650-AZFRM
$280.01 MSRP: $405.00
You Save: $124.99 (31%)
Product Specifications
- Other Name: Reman Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: 7L5Z-12A650-AZF, 7L5Z-12A650-AXE, 7L5Z-12A650-AXF, 7L5Z-12A650-BFE, 7L5Z-12A650-AZE
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Ranger | FX4, Sport, STX, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger ECM, Black Oak Part Number: 3U7Z-12A650-FGA
Product Specifications
- Other Name: Module - Pcm - Black Oak; Engine Control Module (ECM); Engine Control Module
- Replaces: 3L5Z-12A650-ME
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Ranger | Edge, Tremor, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger ECM Part Number: 1U7Z-12A650-FKA
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: 1L5Z-12A650-BDC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger ECM, Black Oak Part Number: 3U7Z-12A650-AZA
Product Specifications
- Other Name: Module - Pcm - Black Oak; Engine Control Module (ECM); Engine Control Module
- Replaces: 3L5Z-12A650-YB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Ranger | Edge, Tremor, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger ECM Part Number: 1U7Z-12A650-FMA
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: 1L5Z-12A650-BBC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger ECM Part Number: F87Z-12A650-AKC
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Manufacturer Note: Powertrain Control Module (PCM) #F87F 12A650-AKC (EEC-V) TYPE:ML2-30E (REPROGRAMMABLE)
- Replaces: F87Z-12A650-AKB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Ranger | Edge, Splash, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger ECM Part Number: 1L5Z-12A650-JB
Product Specifications
- Other Name: Module - Engine Control; Engine Control Module (ECM); Engine Control Module
- Manufacturer Note: Powertrain Control Module (PCM) #1L5F 12A650-JB (EEC-V) TYPE:MP2-1A2 (REPROGRAMMABLE)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger ECM Part Number: 1U7Z-12A650-FCA
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: 1L5Z-12A650-ASG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Ranger | XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger ECM Part Number: 1U7Z-12A650-FDA
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: 1L5Z-12A650-ANG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Ranger | XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger ECM Part Number: 1U7Z-12A650-FLA
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: 1L5Z-12A650-BFC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger ECM Part Number: 1U7Z-12A650-FPA
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module
- Replaces: 1L5Z-12A650-BEC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Ranger | Edge, XL, XLT | 6 Cyl 4.0 L GAS

| Page 1 of 5 |Next >

1-20 of 98 Results

Ford Ranger Engine Control Module

OEM Engine Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Engine Control Module with long life and a perfect fit. Come to our website and find genuine Ford Ranger parts. We keep a wide inventory of OEM Ranger parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Housed in the Ford Ranger is the Engine Control Module (ECM), an important part of the Ford Ranger series citing the automaker's attributes in reliability and performance. The Engine Control Module is basically the virtual control center of the engine as it polymixes and co-ordinates all of the engine's critical parameters including air-fuel mixture, ignition time and speed as well as other engine's conditions depending on the data obtained from various sensors. This leads to optimised performance of the Ford Ranger, with a proven improvement in fuel consumption and safety. Depending on the Ranger model, the Engine Control Module has developed from simple integrated circuits based to more complex microprocessors including the facility for variable valve timing which provides the engine with enhanced features for efficient functioning. The Engine Control Module is famous for its high level of durability and precision; this means that the control system is designed to meet certain needs of the specified model of Ranger while being versatile to adapt to other requirements of driving. Also, Engine Control Module can come both new and rebuilt, so there will be always a perfect match for each car's needs. By continuing to work on increasing efficiency and safety, the Engine Control Module is still an important attribute of the Ford Ranger which strengthens it popular status as a reliable vehicle that provides various features to drivers in terms of performance.

Ford Ranger Engine Control Module Parts and Q&A

ECM
5L5Z-12A650-AMB
Q: How to service the Engine Control Module on Ford Ranger?
A:
The first step to serve the Engine Control Module begins with disconnecting the battery ground cable. Beginning service on the Engine Control Module requires unfastening the powertrain control module (PCM) wiring harness retainer nut while deliberately tightening it to 10 Nm (89 lb-in) torque after reinstallation. When disconnecting the PCM electrical connector you need to tighten it to 7 Nm (62 lb-in) after everything is back in place. Dispose of the stud bolt and place the ground cable and PCM wiring harness aside before tightening both to 10 Nm (89 lb-in). The installation should begin by removing two nuts and the PCM cover while applying 7 Nm (62 lb-in) torque for both. Reposition the PCM before you substitute it with the opposite order used during removal.
ECM
7L5Z-12A650-AZFRM
Q: How to remove and replace the Engine Control Module on Ford Ranger?
A:
Starting the Engine Control Module removal process demands a retrieval of module configuration data following the Programmable Module Installation procedure. The first step is to remove the PCM wiring harness retainer nut followed by the ground wire stud bolt while disconnecting the three PCM electrical connectors. Undertake the removal of both nuts securing the PCM unit before extracting the module from the system. After placing the PCM into its correct position you must fasten it using the two nuts which require a 10 Nm (89 lb-in) torque setting. Fasten the ground wire terminals by installing the stud bolt while tightening it to 10 Nm (89 lb-in). Secure the PCM wiring harness retainer nut by tightening it to 10 Nm (89 lb-in). When installing a new PCM it becomes necessary to reset the parameters inside both the PCM and instrument cluster module to prevent PATS no-start conditions that might affect un-PATS equipped vehicles. The restoration of module configurations for the instrument cluster module and PCM will follow the directions present in the Programmable Module Installation procedure.