How to Bleed the ABS Control Module in the Four Wheel Anti-Lock Brake System (4WABS) Hydraulic Control Unit (HCU) on Ford Taurus?

Start bleeding the Four Wheel Anti-Lock Brake System (4WABS) Hydraulic Control Unit (HCU) by using approved DOT 3 brake fluid since different types of fluid will permanently damage brake parts and disable braking function. Users should protect themselves from brake fluid exposure since the substance contains polyglycols and polyglycol ethers yet they must wash their hands completely after handling this material. Touching brake fluid near your eyes requires the immediate use of running water for 15 minutes before obtaining medical help if the eyes show persistent irritation. Though from a fluid ingestion requires patients to drink water followed by water-triggered vomiting before receiving urgent medical care. Before brake fluid comes into contact with painted or plastic materials it should be immediately cleaned with water. Filling the master cylinder reservoir with the specified brake fluid while actively bleeding must be done to prevent any reuse of discarded fluid. The procedure becomes mandatory when installing a new 4WABS HCU unit. Divide your approach into three sections which first require you to prepare the area before removing the brake master cylinder filler cap and adding specified brake fluid to the reservoir. Attach a clear drain tube with the rear bleeder screw located on the RH while directing the opposite end into a container containing partially full DOT 3 brake fluid. An assistant should pump down and maintain steady pressure on the brake pedal throughout the procedure. During the procedure the assistant should continue pressing the brake pedal after the operator tightens the RH rear bleeder screw when brake fluid starts to flow. The procedure should be repeated until you see clear fluid without bubbles coming from the drainage point and the master cylinder reservoir requires occasional refilling. The provider should tighten each bleeder screw to 15 Nm torque (11 ft. lbs.) after performing bleeder procedures on the LH rear and then continuing with the RH front and finally the LH front screws. The diagnostic tool adapter cable should be connected to the vehicle data link connector under the dash before proceeding with the tool's instructions for bleeding followed by conventional bleeding procedures.

How to Bleed the Brake System After Installing a New ABS Control Module on Ford Taurus?

A suitable drainage procedure for new Four Wheel Anti-Lock Brake System (4WABS) Hydraulic Control Unit (HCU) requires cleanup of dirt from brake master cylinder filler cap followed by fluid addition of DOT 3 or DOT 4 brake fluid into the container while maintaining a non-dry master cylinder. Install a clear drain tube onto the RH rear bleeder screw while placing its other end into brake fluid-filled container for vehicles equipped with rear drum or disc brakes. Apply steady pressure on the brake pedal with an assistant as you open the RH rear bleeder screw until you see clear liquid brake fluid without air bubbles then secure the screw. Illuminate the dropping area before filling up the brake master cylinder reservoir since you will perform brake bleeding operations on the LH rear bleeder screw first then the RH front bleeder screw followed by the LH front bleeder screw. You should connect the NGS DLC cable adapter at the vehicle Data Link Connector DLC under the dash before accessing the help menu on the scan tool through the Ford Service Function Card (FSF) for additional bleeding instructions. Rica the standard bleed procedure which was established earlier. When working with brake fluid be cautious to avoid spreading it onto your eyes and all painted or plastic materials since you must discard the drained fluid entirely.

OEM Ford Taurus ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

27 ABS Control Modules found

View related parts
Ford Taurus Control Module Part Number: 9G1Z-2C219-B
$1257.30 MSRP: $1719.38
You Save: $462.08 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module; Module
- Replaces: 9G1Z-2C219-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Modulator Valve Part Number: FG1Z-2C215-A
$810.56 MSRP: $1108.46
You Save: $297.90 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Replaces: DG1Z-2C405-C, FG1Z-2C405-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Control Module Part Number: FG1Z-2C219-C
$412.01 MSRP: $558.46
You Save: $146.45 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: DG1Z-2C219-C, FG1Z-2C219-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Control Module Part Number: 8G1Z-2C219-D
$588.51 MSRP: $814.15
You Save: $225.64 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 8G1Z-2C219-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Control Module Part Number: AG1Z-2C219-A
$1427.63 MSRP: $1952.31
You Save: $524.68 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | Limited, SE, SEL, SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Modulator Valve Part Number: DG1Z-2C215-C
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Modulator Valve Part Number: 8G1Z-2C346-D
Product Specifications
- Other Name: Module - ABS Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU & HCU
- Replaces: 8G1Z-2C346-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Modulator Valve Part Number: 8G1Z-2C346-E
Product Specifications
- Other Name: Module - ABS Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU & HCU
- Replaces: 8G1Z-2C346-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Modulator Valve Part Number: 9G1Z-2C405-B
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit; Control Assembly
- Replaces: 9G1Z-2C405-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Control Module Part Number: AA5Z-2C219-A
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | Limited, SE, SEL, SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Modulator Valve Part Number: AA5Z-2C405-C
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU & HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | Limited, SE, SEL, SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Control Module Part Number: F1DZ-2C219-A
Product Specifications
- Other Name: Module And Bracket Assembly - Power Steering; ABS Control Module; Module & Brkt Assembly-Power Steering
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Ford Taurus | GL, L, LX, SE, SHO | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Taurus Control Module Part Number: F6DZ2C219DA
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996 Ford Taurus | SHO | 8 Cyl 3.4 L GAS
View related parts
Ford Taurus Control Module Part Number: XF1Z-2C219-AA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: except SHO
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford Taurus | G, GL, LX | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Control Module Part Number: YF1Z-2C219-AA
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Manufacturer Note: ABS only
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2003 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Control Module Part Number: YF1Z-2C219-BA
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Manufacturer Note: ABS & Traction assist
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2003 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Control Module Part Number: YF1Z-2C286-AA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulic; ABS Hydraulic Assembly; ABS Control Module; Hydraulic Control Unit; Control Assembly - ABS Hydraulics
- Manufacturer Note: HCU, ABS only
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2007 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Control Module Part Number: YF1Z-2C286-BA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulic; ABS Hydraulic Assembly; ABS Control Module; Hydraulic Control Unit; Control Assembly - ABS Hydraulics
- Manufacturer Note: HCU, ABS & traction assist
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2007 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Control Module Part Number: YF1Z-2C286-CA
Product Specifications
- Other Name: Control; ABS Hydraulic Assembly; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2007 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Modulator Valve Part Number: 8G1Z-2C346-F
$1805.63 MSRP: $2469.23
You Save: $663.60 (27%)
Product Specifications
- Other Name: Module - ABS Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit; Control Assembly
- Manufacturer Note: ECU & HCU
- Replaces: 8G1Z-2C346-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford Taurus | Limited, SEL | 6 Cyl 3.5 L GAS

| Page 1 of 2 |Next >

1-20 of 27 Results

Ford Taurus ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Ford Taurus parts. We keep a wide inventory of OEM Taurus parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The ABS Control Module is one of the critically important modules in the Ford Taurus series famed for its good working capacity in governing the operation of the anti-locking braking system. The improved ABS Control Module makes sure that the wheels do not lock, thus improving the safety of the vehicle particularly in instances of a heavy brake by avoiding skidding. The ABS Control Module together with the wheel speed sensors, valves, a pump, and an ECU, aims at the detection of the speed of the wheel and reaction by controlling the pressure of the brake. Besides, it enhances the stopping distances and has elements like the integrated electronic stability control and traction control necessary to drive on different roads. There are many generations of the Ford Taurus with the ABS Control Module being changed to fit the requirements of various models to serve the entire line of Taurus vehicles. This adaptability means the ABS Control Module is, therefore, important in improving efficiency and safety of the vehicle to the driver. Furthermore, the hydraulic pressure of the module to support as necessary, is unique in the market automotive industry of Ford Taurus making it a special attribute. Given the company's focus on quality and innovation, the ABS Control Module highlights the company's goal and determination to offering consumers with a safe and dependable ride, making the Taurus to be a dependable car for the consumers.

Ford Taurus ABS Control Module Parts and Q&A

Control Module
4F1Z-2C219-AA
Q: How to Bleed the ABS Control Module in the Four Wheel Anti-Lock Brake System (4WABS) Hydraulic Control Unit (HCU) on Ford Taurus?
A:
Start bleeding the Four Wheel Anti-Lock Brake System (4WABS) Hydraulic Control Unit (HCU) by using approved DOT 3 brake fluid since different types of fluid will permanently damage brake parts and disable braking function. Users should protect themselves from brake fluid exposure since the substance contains polyglycols and polyglycol ethers yet they must wash their hands completely after handling this material. Touching brake fluid near your eyes requires the immediate use of running water for 15 minutes before obtaining medical help if the eyes show persistent irritation. Though from a fluid ingestion requires patients to drink water followed by water-triggered vomiting before receiving urgent medical care. Before brake fluid comes into contact with painted or plastic materials it should be immediately cleaned with water. Filling the master cylinder reservoir with the specified brake fluid while actively bleeding must be done to prevent any reuse of discarded fluid. The procedure becomes mandatory when installing a new 4WABS HCU unit. Divide your approach into three sections which first require you to prepare the area before removing the brake master cylinder filler cap and adding specified brake fluid to the reservoir. Attach a clear drain tube with the rear bleeder screw located on the RH while directing the opposite end into a container containing partially full DOT 3 brake fluid. An assistant should pump down and maintain steady pressure on the brake pedal throughout the procedure. During the procedure the assistant should continue pressing the brake pedal after the operator tightens the RH rear bleeder screw when brake fluid starts to flow. The procedure should be repeated until you see clear fluid without bubbles coming from the drainage point and the master cylinder reservoir requires occasional refilling. The provider should tighten each bleeder screw to 15 Nm torque (11 ft. lbs.) after performing bleeder procedures on the LH rear and then continuing with the RH front and finally the LH front screws. The diagnostic tool adapter cable should be connected to the vehicle data link connector under the dash before proceeding with the tool's instructions for bleeding followed by conventional bleeding procedures.
Control Module
YF1Z-2C286-CA
Q: How to Bleed the Brake System After Installing a New ABS Control Module on Ford Taurus?
A:
A suitable drainage procedure for new Four Wheel Anti-Lock Brake System (4WABS) Hydraulic Control Unit (HCU) requires cleanup of dirt from Brake Master Cylinder filler cap followed by fluid addition of DOT 3 or DOT 4 brake fluid into the container while maintaining a non-dry master cylinder. Install a clear drain tube onto the RH rear bleeder screw while placing its other end into brake fluid-filled container for vehicles equipped with rear drum or disc brakes. Apply steady pressure on the brake pedal with an assistant as you open the RH rear bleeder screw until you see clear liquid brake fluid without air bubbles then secure the screw. Illuminate the dropping area before filling up the brake master cylinder reservoir since you will perform brake bleeding operations on the LH rear bleeder screw first then the RH front bleeder screw followed by the LH front bleeder screw. You should connect the NGS DLC cable adapter at the vehicle Data Link Connector DLC under the dash before accessing the help menu on the scan tool through the Ford Service Function Card (FSF) for additional bleeding instructions. Rica the standard bleed procedure which was established earlier. When working with brake fluid be cautious to avoid spreading it onto your eyes and all painted or plastic materials since you must discard the drained fluid entirely.