How to service and repair the wheel spindle on Lincoln MKZ?

Begin wheel spindle service and repair operations by taking out the wheel bearing along with wheel hub assembly. You should remove the brake disc shield by taking out its three bolts first while tightening it back to 23 Nm (17 ft. lbs.) during reinstallation. The wheel spindle can be detached by removing the four spindle bolts before installation where their torque should be set at 140 Nm (103 ft. lbs.). The service will experience severe consequences if someone uses a wheel spindle part of lesser quality or with a different number than the original one that needs switching. Reinstall all critical suspension fasteners by using specified torque values so these components maintain their proper retention.

How to properly service and repair the spindle on Lincoln Navigator?

The spindle service process begins with power shut-off to air suspension through kicking off the RH switch in the panel to avoid sudden air spring changes that might cause vehicle position shifts during work. Start by lifting and securing the vehicle and then take off the tire assembly together with the wheel before removing the brake disc shield. A High-Lift Jack should support the lower arm before removing its upper ball joint castle nut along with the discarding of the cotter pin before continuing with the nut removal. A Pitman Arm Puller allows users to detach the ball joint from the front wheel spindle before they remove the upper shock absorber nut and washer and finally take off the front shock absorber through lower nuts. Proceed by taking out the tie-rod castle nut then discard the cotter pin before loosening the nut, and reapply the Pitman Arm Puller to free the tie-rod end from the front wheel spindle. Fold the front coil spring with a Coil Spring Compressor tool before removing the lower ball joint castle nut while also discarding the cotter pin so you can detach the castle nut. Use a Pitman Arm Puller to disconnect and separate both the lower ball joint while ending the procedure by taking off the front wheel spindle. New cotter pins must be installed during assembly while following the reverse steps of removal and checking the front end alignment before final installation.

OEM Lincoln Spindle

Axle Spindle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Spindles found

View related parts
Lincoln Knuckle, Front Driver Side Part Number: 2L3Z-3106-AA
Product Specifications
- Other Name: Spindle; Steering Knuckle, Front Left
- Manufacturer Note: L.H., 4x2
- Position: Front Driver Side
- Replaces: F75Z-3106-AB
Fits the following Lincoln Models:
- Blackwood | 2002 | Base | 8 Cyl 5.4 L GAS
- Navigator | 1998-2002 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Knuckle, Front Passenger Side Part Number: 2L3Z-3105-AA
Product Specifications
- Other Name: Spindle; Steering Knuckle, Front Right
- Manufacturer Note: R.H., 4x2
- Position: Front Passenger Side
- Replaces: F75Z-3105-AB
Fits the following Lincoln Models:
- Blackwood | 2002 | Base | 8 Cyl 5.4 L GAS
- Navigator | 1998-2002 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Spindle, Rear Passenger Side Part Number: 3F1Z-4A013-BB
Product Specifications
- Other Name: Suspension Knuckle, Rear Right; Knuckle
- Manufacturer Note: R.H., with 18mm diameter hole for anti-lock sensor
- Position: Rear Passenger Side
Fits the following Lincoln Models:
- Continental | 1995-1996 | Anniversary, Diamond Anniversary, Signature, Spinnaker Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Spindle, Rear Driver Side Part Number: 3F1Z-4A013-BA
Product Specifications
- Other Name: Suspension Knuckle, Rear Left; Knuckle
- Manufacturer Note: L.H., with 18mm diameter hole for anti-lock sensor
- Position: Rear Driver Side
Fits the following Lincoln Models:
- Continental | 1995-1996 | Anniversary, Diamond Anniversary, Signature, Spinnaker Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Spindle, Passenger Side Part Number: XF1Z-4A013-AB
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
Fits the following Lincoln Models:
- Continental | 1988-1994 | Base, Executive, Signature | 6 Cyl 3.8 L GAS
View related parts
Lincoln Spindle, Driver Side Part Number: XF1Z-4A013-AA
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
Fits the following Lincoln Models:
- Continental | 1990-1994 | Base, Executive, Signature | 6 Cyl 3.8 L GAS
View related parts
Lincoln Spindle, Passenger Side Part Number: F7OZ-4A013-BA
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
Fits the following Lincoln Models:
- Continental | 1997-2002 | Base, Spinnaker Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Spindle, Driver Side Part Number: F7OZ-4A013-AA
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
Fits the following Lincoln Models:
- Continental | 1997-2002 | Base, Spinnaker Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Knuckle, Driver Side Part Number: F5AZ-3106-A
Product Specifications
- Other Name: Spindle
- Position: Driver Side
Fits the following Lincoln Models:
- Town Car | 1995-2002 | Anniversary, Base, Cartier, Cartier L, Cypress, Executive, Executive L, Signature, Touring Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Knuckle, Passenger Side Part Number: F5AZ-3105-A
Product Specifications
- Other Name: Spindle
- Position: Passenger Side
Fits the following Lincoln Models:
- Town Car | 1995-2002 | Anniversary, Base, Cartier, Cartier L, Cypress, Executive, Executive L, Signature, Touring Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Knuckle, Passenger Side Part Number: F1VY3105A
Product Specifications
- Other Name: Spindle
- Position: Passenger Side
Fits the following Lincoln Models:
- Town Car | 1991-1994 | Base, Cartier, Cypress, Executive, Jack Nicklaus, Signature, Touring Edition, Tournament Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Knuckle, Front Driver Side Part Number: 7L3Z-3106-A
Product Specifications
- Other Name: Spindle; Steering Knuckle, Front Left
- Position: Front Driver Side
- Replaces: 6L3Z-3106-AB
Fits the following Lincoln Models:
- Mark LT | 2006-2008 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Knuckle, Front Passenger Side Part Number: 7L3Z-3105-A
Product Specifications
- Other Name: Spindle; Steering Knuckle, Front Right
- Position: Front Passenger Side
- Replaces: 6L3Z-3105-AB
Fits the following Lincoln Models:
- Mark LT | 2006-2008 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Knuckle Assembly, Rear Passenger Side Part Number: 7E5Z-4A013-R
Product Specifications
- Other Name: Spindle; Suspension Knuckle Assembly, Rear Right
- Position: Rear Passenger Side
Fits the following Lincoln Models:
- MKZ | 2007-2009 | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln Knuckle Assembly, Rear Driver Side Part Number: 7E5Z-4A013-L
Product Specifications
- Other Name: Spindle; Suspension Knuckle Assembly, Rear Left
- Position: Rear Driver Side
Fits the following Lincoln Models:
- MKZ | 2007-2009 | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln Spindle, Rear Passenger Side Part Number: 3M8Z-4A013-R
Product Specifications
- Other Name: Stub Axle, Rear Right
- Position: Rear Passenger Side
Fits the following Lincoln Models:
- MKZ | 2007-2012 | Base, Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
- Zephyr | 2006 | Base | 6 Cyl 3.0 L GAS
View related parts
Lincoln Spindle, Rear Driver Side Part Number: 3M8Z-4A013-L
Product Specifications
- Other Name: Shaft; Stub Axle, Rear Left
- Position: Rear Driver Side
Fits the following Lincoln Models:
- MKZ | 2007-2012 | Base, Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
- Zephyr | 2006 | Base | 6 Cyl 3.0 L GAS

Lincoln Spindle

If you own Lincoln and want to keep it in top shape, choosing OEM Spindle is a smart move. They are precisely engineered and follow strict factory standards. They are made in advanced facilities that use cutting edge technology. Each part goes through thorough testing to confirm strength and safety, so you can trust it. FordPartsDeal.com gives you genuine Lincoln Spindle at some of the affordable online prices without cutting quality. Every OEM Lincoln part includes the manufacturer's warranty, easy returns, and super-fast delivery. So why wait? Shop now and get your vehicle back to peak condition.

Lincoln Spindle connects wheel and steering forces providing drivers with rapid feedback and solid cornering assurance. Lincoln is concentrated on quiet cabins where Quiet Flight is applied to shut out road noise, eliminate vibration through several panels, and circulate fresh air without turbulence to ensure that conversations remain gentle as city mayhem rocks the house. Lincoln equips all their models with Co-Pilot360 which has lane keeping, blind-spot warnings, auto high-beams, and smart parking assistance which pop in anytime it feels it is necessary but will never override the driver. Lincoln provides ActiveGlide on some trims that can update maps on-air provided there are enough highways to venture without straining hands and the sensors monitor the lanes, distance, and gaze. The combination of soft leather, real wood, and transparent digital clusters in Lincoln is relaxing as it proves that quiet luxury can calm the nerves and display the information in an understandable manner rather than futilely search loud gimmicks. The Spindle is in between knuckle and hub; it has bumps, twists with steering and forces brake and keeps a definite camber on front, back or all-wheel design, and the high density of metal and tight machining prevents flexing. Every Spindle is built upon a forged high-strength core that scowls away rust, heat, gravel blows, and continuous side forces, thus suspension geometry remains fixed despite years of pothole abuse. Consistent inspections prevent play before it increases since a sound Spindle clamps bearings of the wheels at right angles, ABS sensors show clean, and shocks concentrate on vertical work rather than chasing wobble. Paired together, a new Spindle will put a new crisp turn-in and eliminate brake shimmy permanently.

Lincoln Spindle Parts and Q&A

Knuckle Assembly, Rear Driver Side
7E5Z-4A013-L
Q: How to service and repair the wheel spindle on Lincoln MKZ?
A:
Begin wheel spindle service and repair operations by taking out the wheel bearing along with wheel hub assembly. You should remove the brake disc shield by taking out its three bolts first while tightening it back to 23 Nm (17 ft. lbs.) during reinstallation. The wheel spindle can be detached by removing the four spindle bolts before installation where their torque should be set at 140 Nm (103 ft. lbs.). The service will experience severe consequences if someone uses a wheel spindle part of lesser quality or with a different number than the original one that needs switching. Reinstall all critical suspension fasteners by using specified torque values so these components maintain their proper retention.
Knuckle, Front Driver Side
2L3Z-3106-AA
Q: How to properly service and repair the spindle on Lincoln Navigator?
A:
The spindle service process begins with power shut-off to air suspension through kicking off the RH switch in the panel to avoid sudden air spring changes that might cause vehicle position shifts during work. Start by lifting and securing the vehicle and then take off the tire assembly together with the wheel before removing the brake disc shield. A High-Lift Jack should support the lower arm before removing its upper ball joint castle nut along with the discarding of the cotter pin before continuing with the nut removal. A Pitman Arm Puller allows users to detach the ball joint from the front wheel spindle before they remove the upper shock absorber nut and washer and finally take off the front shock absorber through lower nuts. Proceed by taking out the tie-rod castle nut then discard the cotter pin before loosening the nut, and reapply the Pitman Arm Puller to free the tie-rod end from the front wheel spindle. Fold the front coil spring with a Coil Spring Compressor tool before removing the lower ball joint castle nut while also discarding the cotter pin so you can detach the castle nut. Use a Pitman Arm Puller to disconnect and separate both the lower ball joint while ending the procedure by taking off the front wheel spindle. New cotter pins must be installed during assembly while following the reverse steps of removal and checking the front end alignment before final installation.