How to replace the wheel bearing on Mercury Capri?

For early models with the bearing pressed onto the axleshaft, a hydraulic press and special tools are necessary for replacement. Begin by removing the axleshaft and then have a dealer service department or automotive machine shop handle the bearing replacement. In later models, first remove the axleshaft and the oil seal. A bearing puller or a specially fabricated tool that engages behind the bearing will be needed; to remove the axle bearing, insert a bearing removal tool attached to a slide hammer through the center, pull the tool against the back side, and use the slide hammer to yank the bearing from the axle housing. After that, attach a slide hammer to pull the bearing out of the axle housing. Clean the bearing recess and drive in the new bearing using a correctly-sized bearing driver, ensuring it is lubricated with gear lubricant and tapped into the full depth of its recess. Finally, discard the old oil seal and install a new one before reinstalling the axleshaft.

How to inspect and service front wheel bearings on Mercury Grand Marquis?

When inspecting and servicing front wheel bearings, lift the car and listen to noise, resistance, and free play on each tire. In case it moves, take off the cap of the dust, nut washer, nut lock, and cotter pin. The spindle should be pushed to detach the hub from the outer bearing. Then take out the seal by removing the hub from it. Inspect and exchange any components that are defective or excessively worn out. Fill with grease bearings as well as lubricate spindles and hubs with grease. Put on a seal, inner bearing, and outer bearing (in this order). Use a washer and nut for securing them together. While spinning the hub, tighten up a nut so that later excess grease may be removed. A new nut lock plus cotter pin should be used for fastening it tightly enough while installing a dust cap, caliper and tire back again. You can now lower your vehicle to test its bearings.

OEM Mercury Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Wheel Bearings found

View related parts
Mercury Axle Bearing, Rear Part Number: E3TZ-1225-AA
$17.74 MSRP: $25.17
You Save: $7.43 (30%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Ball; Drive Axle Shaft Bearing, Rear; Wheel Bearing; Axle Bearings; Shaft Bearings; Axle Shaft Bearing; Bearing
- Position: Rear
- Replaces: E3TZ-1225-A
Fits the following Mercury Models:
- Mountaineer | 1997-2001 | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Hub & Bearing, Rear Part Number: F5RZ-1104-B
$76.07 MSRP: $103.52
You Save: $27.45 (27%)
ADD TO CART
Product Specifications
- Other Name: Hub And Bearing Assembly; Wheel Hub Assembly; Wheel Hub Repair Kit; Wheel Hub Module.; Hub; Hub And Bearing Assembly - Wheel
- Manufacturer Note: Rear - includes sensor ring - remove ring if not required
- Position: Rear
Fits the following Mercury Models:
- Cougar | 1999-2002 | Base, S, V6 | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
- Mystique | 1995-2000 | Base, GS, GS Spree, LS, LS Young America | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Mercury Wheel Bearing, Front Part Number: F5RZ-1215-A
$18.06 MSRP: $24.99
You Save: $6.93 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Wheel Hub; Axle Bearing; Front Wheel Bearing
- Manufacturer Note: Front , bearing only
- Position: Front
Fits the following Mercury Models:
- Cougar | 1999-2002 | Base, S, V6 | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
- Mystique | 1995-2000 | Base, GS, GS Spree, LS, LS Young America | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Mercury Wheel Bearings, Front Outer Part Number: B5A-1216-A
$19.52 MSRP: $28.42
You Save: $8.90 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cone And Roller - Bearing; Front Outer Wheel Bearing and Race Set; Taper Bearing Cone; Axle Bearing; Front Wheel Bearing; Outer Wheel Bearing; Outer Bearing; Bearing; Wheel Bearing
- Position: Front Outer
Fits the following Mercury Models:
- Mountaineer | 1997-2001 | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Wheel Bearings, Front Part Number: YL8Z-1215-AA
$43.97 MSRP: $69.82
You Save: $25.85 (38%)
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Wheel Hub; Wheel Bearing, Front; Wheel Hub Repair Kit; Wheel Hub Kit; Axle Bearing; Inner Bearing; Bearing; Wheel Bearing
- Position: Front
Fits the following Mercury Models:
- Mariner | 2005-2011 | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Front Wheel Bearing Part Number: 3M8Z-1215-A
$46.66 MSRP: $76.22
You Save: $29.56 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Wheel Hub; Wheel Bearing, Front, Rear; Wheel Hub Repair Kit; Axle Bearing; Rear Wheel Bearing; Bearing; Wheel Bearing
- Position: Front
- Replaces: F32Z-1215-A
Fits the following Mercury Models:
- Milan | 2006-2011 | Base, Hybrid, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Wheel Bearing, Front Outer Part Number: E7TZ-1216-A
$21.41 MSRP: $29.14
You Save: $7.73 (27%)
ADD TO CART
Product Specifications
- Other Name: Cone And Roller - Bearing; Wheel Bearing, Front Outer; Taper Bearing Cone; Axle Bearing; Bearings; Wheel Bearings; Front Wheel Bearing; Rear Wheel Bearing; Outer Bearing; Bearing
- Position: Front Outer
Fits the following Mercury Models:
- Capri | 1985-1986 | 5.0, GS, RS | 4 Cyl 2.3 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 5.0 L GAS
- Colony Park | 1987-1991 | GS, LS | 8 Cyl 5.0 L GAS
- Cougar | 1984-1990 | Base, LS, XR-7 | 4 Cyl 2.3 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 5.0 L GAS
- Grand Marquis | 1984-1991 | Base, Colony Park, GS, LS | 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS
- Lynx | 1984-1987 | Base, GL, GS, L, LS, LTS, RS, XR3 | 4 Cyl 1.6 L GAS, 4 Cyl 1.9 L GAS, 4 Cyl 2.0 L DIESEL
- Marquis | 1984-1986 | Base, Brougham | 4 Cyl 2.3 L GAS, 4 Cyl 2.3 L LPG, 6 Cyl 3.8 L GAS
- Sable | 1986-1995 | GS, LS, LTS | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
- Topaz | 1984-1994 | Base, GS, GS AWD, LS, LS AWD, LTS, LTS AWD, Sport, Sport AWD, XR5, XR5 AWD | 4 Cyl 2.0 L DIESEL, 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View More
View related parts
Mercury Wheel Bearings, Rear Part Number: 6L2Z-1215-A
$54.14 MSRP: $90.73
You Save: $36.59 (41%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Wheel Hub; Wheel Bearing and Race Set, Rear; Wheel Bearing, Rear; Axle Bearing; Bearing; Wheel Bearing
- Position: Rear
- Replaces: 3L2Z-1215-AA
Fits the following Mercury Models:
- Mountaineer | 2002-2010 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Wheel Bearing Part Number: DV6Z-4221-A
$16.00 MSRP: $23.28
You Save: $7.28 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Ball; Differential Bearing; Axle Bearing; Front Wheel Bearing; Axle Bearings; Differential Bearings; Outer Bearing; Side Bearings; Bearing
- Replaces: B7A-4221-A
Fits the following Mercury Models:
- Capri | 1984-1986 | 5.0, GS, RS, RS Turbo | 4 Cyl 2.3 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 5.0 L GAS
- Cougar | 1984-1997 | Base, LS, XR-7 | 4 Cyl 2.3 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
- Marquis | 1984-1986 | Base, Brougham | 4 Cyl 2.3 L GAS, 4 Cyl 2.3 L LPG, 6 Cyl 3.8 L GAS
- Mountaineer | 2002-2010 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View More
View related parts
Mercury Front Hub & Bearing Part Number: 4L2Z-1102-AC
$177.91 MSRP: $292.73
You Save: $114.82 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub; Wheel Hub Repair Kit; Wheel Hub
- Replaced by: G2MZ-1104-AE
Fits the following Mercury Models:
- Mountaineer | 2002-2005 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Hub & Bearing, Front Part Number: G2MZ-1104-W
$167.40 MSRP: $281.82
You Save: $114.42 (41%)
ADD TO CART
Product Specifications
- Other Name: Hub Assembly - Wheel; Front Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit.; Hub Assembly; Front Hub & Bearing
- Position: Front
- Replaces: F5TZ-1104-A, F87Z-1104-CA, HUB-8
Fits the following Mercury Models:
- Mountaineer | 1997-2001 | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Wheel Bearing, Front Part Number: F7CZ-1215-AA
$28.44 MSRP: $38.71
You Save: $10.27 (27%)
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Wheel Hub; Axle Bearing; Front Wheel Bearing; Bearing
- Position: Front
- Replaces: F4CZ-1215-A
Fits the following Mercury Models:
- Tracer | 1991-1999 | Base, GS, LS, LTS, Trio | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L GAS, 4 Cyl 2.0 L GAS
View related parts
Mercury Wheel Bearing, Rear Part Number: E9DZ-1215-A
$47.68 MSRP: $64.88
You Save: $17.20 (27%)
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly - Wheel Hub; Wheel Bearing and Race Set, Rear; Axle Bearing; Wheel Bearings; Front Wheel Bearing; Rear Wheel Bearing; Bearing
- Position: Rear
Fits the following Mercury Models:
- Cougar | 1989-1997 | LS, XR-7 | 6 Cyl 3.8 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
- Sable | 1986-1995 | GS, LS, LTS | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Hub Assembly Part Number: F7XZ1109BB
Product Specifications
- Other Name: Hub Assembly - Wheel; includes Wheel Bearing, Hub Repair Kit, and Axle Bearing.; Hub; Bearing
Fits the following Mercury Models:
- Villager | 1993-1998 | GS, LS, Nautica | 6 Cyl 3.0 L GAS
View related parts
Mercury Front Wheel Bearing Part Number: F3XY-3123-A
Product Specifications
- Other Name: Bearing Assembly - Thrust; Wheel Bearing; Axle Bearing; Bearing
Fits the following Mercury Models:
- Villager | 1993-2002 | Base, Estate, GS, LS, Nautica, Sport | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Mercury Wheel Bearing, Front Part Number: E7GZ-1216-B
Product Specifications
- Other Name: Bearing Assembly - Wheel; Multi-Purpose Bearing; Needle Bearing; Axle Bearing; Wheel Bearings; Front Wheel Bearing; Outer Bearing; Bearing; Bearing Assembly - Wheel Hub
- Manufacturer Note: Front - inner & outer
- Position: Front
Fits the following Mercury Models:
- Capri | 1991-1994 | Base, XR2 | 4 Cyl 1.6 L GAS
- Tracer | 1988-1989 | Base | 4 Cyl 1.6 L GAS

Mercury Wheel Bearing

If you own Mercury and want to keep it in top shape, choosing OEM Wheel Bearing is a smart move. They are precisely engineered and follow strict factory standards. They are made in advanced facilities that use cutting edge technology. Each part goes through thorough testing to confirm strength and safety, so you can trust it. FordPartsDeal.com gives you genuine Mercury Wheel Bearing at some of the affordable online prices without cutting quality. Every OEM Mercury part includes the manufacturer's warranty, easy returns, and super-fast delivery. So why wait? Shop now and get your vehicle back to peak condition.

Mercury Wheel Bearing reduces friction, maintains wheel rotation on course, and enhances road safety regardless of the ride. In 1938, Mercury cut its lane by combining aggressive styling with a more comfortable ride that got the attention and appreciation of everyday drivers on their way to work. Mercury interiors silenced road noise, provided comfortable seating, and placed controls in the places the hands like to fall, which made long trips seem shorter and talking easy. Mercury was able to focus on comfort versus cost and provided shoppers with value without compromising the confident suspension tuning that over decades made such models as Cougar and Grand Marquis memorable with decades of highway service. Mercury continued to roll out daily advances in technology, such as smoother steering racks, tightening of the body seals, ingenious insulation of the cabin, and so forth, which showed that innovation does not require a luxury label to count in the real world. The Wheel Bearing units are pressed into the hub assembly, and hardened steel races are applied together with rollers well machined to slash rotational drag, and the wheel and tire remain in a steady position when potholes are encountered or cornering forces increase. An optional ABS sensor is also located in Wheel Bearing, which allows the car to monitor wheel speed without the need for additional components to be attached to the car. Wheel Bearing failure notifies itself with its rumbling sound or vibration, and thus changing the closed part saves tire wobble and steering confidence in the swapping. The grease and proper torque should be applied during the installation of Wheel Bearing because otherwise heat accumulates and the joint may loosen or even be frozen.

Mercury Wheel Bearing Parts and Q&A

Wheel Bearing, Front
E7GZ-1216-B
Q: How to replace the wheel bearing on Mercury Capri?
A:
For early models with the bearing pressed onto the axleshaft, a hydraulic press and special tools are necessary for replacement. Begin by removing the axleshaft and then have a dealer service department or automotive machine shop handle the bearing replacement. In later models, first remove the axleshaft and the oil seal. A bearing puller or a specially fabricated tool that engages behind the bearing will be needed; to remove the axle bearing, insert a bearing removal tool attached to a slide hammer through the center, pull the tool against the back side, and use the slide hammer to yank the bearing from the axle housing. After that, attach a slide hammer to pull the bearing out of the axle housing. Clean the bearing recess and drive in the new bearing using a correctly-sized bearing driver, ensuring it is lubricated with gear lubricant and tapped into the full depth of its recess. Finally, discard the old oil seal and install a new one before reinstalling the axleshaft.
Wheel Bearing, Front Outer
E7TZ-1216-A
Q: How to inspect and service front wheel bearings on Mercury Grand Marquis?
A:
When inspecting and servicing front wheel bearings, lift the car and listen to noise, resistance, and free play on each tire. In case it moves, take off the cap of the dust, nut washer, nut lock, and cotter pin. The spindle should be pushed to detach the hub from the outer bearing. Then take out the seal by removing the hub from it. Inspect and exchange any components that are defective or excessively worn out. Fill with grease bearings as well as lubricate spindles and hubs with grease. Put on a seal, inner bearing, and outer bearing (in this order). Use a washer and nut for securing them together. While spinning the hub, tighten up a nut so that later excess grease may be removed. A new nut lock plus cotter pin should be used for fastening it tightly enough while installing a dust cap, caliper and tire back again. You can now lower your vehicle to test its bearings.