Other Name: Regulator And Motor Assembly - Window; Window Regulator, Rear Left; Window Assembly
Manufacturer Note: Includes Motor
Position: Rear Driver Side
Fits the following Mercury Models:
Mariner | 2007-2011 | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
Other Name: Regulator And Motor Assembly - Window; Window Regulator, Front Left; Power Window Motor and Regulator Assembly
Manufacturer Note: Includes Motor
Position: Front Driver Side
Replaces: 8L8Z-7823201-A
Fits the following Mercury Models:
Mariner | 2007-2011 | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
Other Name: Regulator And Motor Assembly - Window; Front Right; Power Window Motor and Regulator Assembly; Window Switch
Manufacturer Note: Includes Motor
Position: Front Passenger Side
Replaces: 8L8Z-7823200-A
Fits the following Mercury Models:
Mariner | 2007-2011 | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
Other Name: Regulator And Motor Assembly - Window; Window Regulator, Rear Right; Window Assembly
Manufacturer Note: Includes Motor
Position: Rear Passenger Side
Fits the following Mercury Models:
Mariner | 2007-2011 | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
Q: How to service the front Power Window Motor and Window Regulator on Mercury Cougar?
A: The service process for front door window motor and regulator begins by taking out the door glass and separating the door speaker and removing the electrical connector. A plastic knife can be used to cut through the Butyl strip of the watershield yet care must be taken to not touch the adhesive side to protect its ability to re-bond. The watershield must be peeled back beyond the door speaker housing to get better access for service. First disconnect the regulator motor electrical connector before moving on to remove the regulator guide and separate the motor and regulator units through nuts removal and rivet drilling. The installation process demands the exact opposite of the removal steps.
Q: How to service and repair the front door window regulator on Mercury Grand Marquis?
A: A service or repair process for the front door window regulator begins with front door trim panel removal and watershield placement out of the way. The first action should remove the speaker and driver door module followed by the pull strap handle. First disconnect the connector then remove the front door window glass after which disconnect the rivets. The Torx® screws and the nuts must be removed prior to finally taking out the regulator. The installation method requires you to perform the steps in reverse order of removal.
Q: How to service the front door window regulator on Mercury Mariner?
A: Service of the front door window regulator begins by taking out the front door trim panel together with its bracket holding screw. Begin by placing the watershield to the side and linking the window control switch electrical connector before budgeting the battery power. Lower the front door window glass by using the window control switch to reach the screws on the glass before detaching both the battery power and the window control switch electrical connector. Uninstall the screws fastening the front door window glass before tightening them to 5 Nm (44 lb-in) when reattaching the window glass. Support the front door window glass in its maximum position before disconnecting the motor electrical connector and removing bolts that maintain the front door window regulator while tightening them to 6 Nm (53 lb-in) for installation. To finish the procedure complete reverse the removal steps while tightening the two front door window regulator and motor nuts to 6 Nm (53 lb-in) before reinstalling them.