How to Properly Service and Repair a Tail Pipe and Muffler on 2007 Ford Crown Victoria?

You should initiate muffler and tailpipe servicing by placing your vehicle in NEUTRAL on the hoist system. The lifting procedure must start by shutting off air suspension electrical power to avoid unexpected spring changes that may cause vehicle movement. The two nuts and clamp need removal before installation where tightening to 48 Nm (35 ft. lbs.) becomes necessary. Make use of a suitable exhaust cutting tool to disconnect the muffler from the tailpipe. Perform an evaluation of isolators for quality before you detach the isolators to eliminate the tailpipe. Perform the same steps for the muffler while inspecting the necessary isolator for possible replacement. New exhaust fasteners should replace old ones during installation then the fasteners should remain loose until all components join before final tightening. Use a systematic tightening method to specify these fasteners which will achieve uniform assembly of the flanges before concluding at 33 Nm (24 ft. lbs.). Using oil or grease-based lubricants represents a danger to ISO T2 the isolators and their rubber components because these substances will degrade the rubber material and permit the isolators to break away from their exhaust hanger bracket position when the vehicle runs.

OEM 2007 Ford Crown Victoria Tail Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Tail Pipes found

View related parts
2007 Ford Crown Victoria Front Pipe
Part Number: 4W7Z-5246-CA
$194.54 MSRP: $269.12
You Save: $74.58 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe
- Replaces: 3W7Z-5246-CA
- Base No.: 5246
- Item Weight: 9.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4W7Z-5246-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Base, LWB, LX, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2007 Ford Crown Victoria Inlet Pipe
Part Number: 4W7Z-5246-BA
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Crossover Pipe; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Front Pipe
- Replaces: 3W7Z-5246-BA
- Base No.: 5246
- Item Weight: 20.90 Pounds
- Item Dimensions: 46.2 x 10.1 x 26.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4W7Z-5246-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2007 Ford Crown Victoria Muffler, Front Passenger Side
Part Number: 7W7Z-5230-AA
Product Specifications
- Other Name: Muffler Assembly - Front
- Position: Front Passenger Side
- Replaces: 6W7Z-5230-AA
- Base No.: 5230
- Item Weight: 22.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7W7Z-5230-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2007 Ford Crown Victoria Muffler, Front Driver Side
Part Number: 6W7Z-5230-A
Product Specifications
- Other Name: Muffler Assembly - Front
- Manufacturer Note: LH muffler with fire protection, FROM 8/3/2005
- Position: Front Driver Side
- Replaces: 5W7Z-5230-FB, 6W7Z-5230-AB
- Base No.: 5230
- Item Weight: 23.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W7Z-5230-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2007 Ford Crown Victoria Muffler, Rear Passenger Side
Part Number: 6W7Z-5230-BA
Product Specifications
- Other Name: Muffler Assembly - Centre And Rear; Exhaust Muffler, Right
- Position: Rear Passenger Side
- Replaces: 4W7Z-5230-DA, 5W7Z-5230-BA
- Base No.: 5230
- Item Weight: 22.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W7Z-5230-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2007 Ford Crown Victoria Inlet Pipe
Part Number: 4W7Z-5246-AA
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Crossover Pipe; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Front Pipe
- Replaces: 3W7Z-5246-AA
- Base No.: 5246
- Item Weight: 11.00 Pounds
- Item Dimensions: 36.7 x 20.4 x 12.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4W7Z-5246-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS

2007 Ford Crown Victoria Tail Pipe

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2007 Ford Crown Victoria Tail Pipe available at FordPartsDeal.com. You can confidently purchase our OEM 2007 Ford Crown Victoria Tail Pipe as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2007 Ford Crown Victoria Tail Pipe Parts Questions & Experts Answers

Q: How to Properly Service and Repair a Tail Pipe and Muffler on 2007 Ford Crown Victoria?
A: You should initiate muffler and tailpipe servicing by placing your vehicle in NEUTRAL on the hoist system. The lifting procedure must start by shutting off air suspension electrical power to avoid unexpected spring changes that may cause vehicle movement. The two nuts and clamp need removal before installation where tightening to 48 Nm (35 ft. lbs.) becomes necessary. Make use of a suitable exhaust cutting tool to disconnect the muffler from the tailpipe. Perform an evaluation of isolators for quality before you detach the isolators to eliminate the tailpipe. Perform the same steps for the muffler while inspecting the necessary isolator for possible replacement. New exhaust fasteners should replace old ones during installation then the fasteners should remain loose until all components join before final tightening. Use a systematic tightening method to specify these fasteners which will achieve uniform assembly of the flanges before concluding at 33 Nm (24 ft. lbs.). Using oil or grease-based lubricants represents a danger to ISO T2 the isolators and their rubber components because these substances will degrade the rubber material and permit the isolators to break away from their exhaust hanger bracket position when the vehicle runs.