How to Bleed the Brake System After Installing a New ABS Control Module on Ford E-250?

Start brake bleeding procedures after new four-wheel anti-lock brake system (4WABS) hydraulic control unit (HCU) installation or when opening the HCU lines by first cleaning brake master cylinder filler cap dirt before filling the reservoir with clean DOT 3 brake fluid. A waste line made from clear tubing should link with the right-hand (RH) rear bleeder screw with the waste end positioned below clean DOT 3 brake fluid. Apply pressure to the brake pedal as an assistant tightens the RH rear bleeder screw at a point when brake fluid starts to flow. Follow this procedure until the brake fluid runs clear without bubbles then restart the reservoir as required. It is necessary to repeat the bleeding procedure that begins with tightening the LH rear bleeder screw to 15 Nm (11 ft. lbs.) followed by disconnecting the waste line and proceeding through the RH front disc brake caliper bleeder screw and finally the LH front disc brake caliper bleeder screw in sequence. The diagnostic tool needs to be connected to the data link connector (DLC) in order to perform the bleeding procedure following the tool instructions that match the original steps.

How to Service and Repair the ABS Control Module on Ford E-250?

The service and repair process for the Electronic Brake Control Module must start by taking out the Hydraulic Control Unit (HCU). The next step requires the removal of screws which are securing the ABS module. Finish the installation process by following the backward order of the removal steps.

OEM Ford E-250 ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 ABS Control Modules found

View related parts
Ford E-250 Control Module Part Number: 9C2Z-2C219-G
$515.04 MSRP: $693.85
You Save: $178.81 (26%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 9C2Z-2C219-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2014 Ford E-250 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Modulator Valve Part Number: 9C2Z-2C215-A
$904.61 MSRP: $1237.08
You Save: $332.47 (27%)
ADD TO CART
Product Specifications
- Other Name: Module; ABS Control Module; ABS Control Unit
- Replaces: 8C2Z-2C286-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2014 Ford E-250 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Modulator Valve Part Number: 9C2Z-2C215-B
$548.40 MSRP: $793.69
You Save: $245.29 (31%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Module; ABS Control Module; ABS Control Unit
- Replaces: 8C2Z-2C286-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2014 Ford E-250 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Control Module Part Number: BC2Z-2C219-A
$513.79 MSRP: $692.15
You Save: $178.36 (26%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2014 Ford E-250 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Control Valve Part Number: 7C2Z-2C219-CA
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 6C2Z-2C219-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Modulator Valve Part Number: 6C2Z-2C286-CA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Replaces: 2C2Z-2C286-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Modulator Valve Part Number: 6C2Z-2C286-BA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Speed Sensor Part Number: 6L3Z-2B373-A
$774.00 MSRP: $1058.46
You Save: $284.46 (27%)
Product Specifications
- Other Name: Valve Assembly - Modulator; ABS Hydraulic Assembly; Control Valve; Control Module; Modulator Valve
- Replaces: XL3Z-2B373-BARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Control Valve Part Number: 8C2Z-2C219-CG
$417.51 MSRP: $563.08
You Save: $145.57 (26%)
Product Specifications
- Other Name: Control; ABS Control Module; Control Module
- Replaces: 8C2Z-2C219-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford E-250 | Base | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Control Valve Part Number: 8C2Z-2C219-A
Product Specifications
- Other Name: Control; ABS Control Module; Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford E-250 | Base | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Control Valve Part Number: 7C2Z-2C219-FA
Product Specifications
- Other Name: Control; ABS Control Module; Control Module
- Replaces: 6C2Z-2C219-FA, 6C2Z-2C219-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Control Module Part Number: 3L3Z-2C286-AARM
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Control Module Part Number: AC2Z-2C219-A
$499.23 MSRP: $673.85
You Save: $174.62 (26%)
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2010 Ford E-250 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Control Valve Part Number: 3C2Z-2C286-AARM
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS

Ford E-250 ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Ford E-250 parts. We keep a wide inventory of OEM E-250 parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Ford E-250 ABS Control Module is an essential component in the Anti lock Braking system of Ford E-250 vehicles that has gain a reputation in the market for its reliability and performance. This module is very important in braking heavy loads from locking the wheels thus improving safety and functionality of the train. The Ford E-250 ABS Control Module is made up of absolute inputs and a series of outputs including wheel speed sensor inputs, valves, a pump, and an ECU section controlling the advanced diagnostics of the ABS modulator. All together, they provide the premier control of the brake pressure and the restoration of the hydraulic pressure for the automated braking that is far beyond human reflexes. There has been different models of the Ford E-250 with reference to the ABS Control Module, and each succeeding generation comes with features such as electronic stability control and traction control to enhance control of the vehicle in different road conditions. This evolution shows that Ford E-250 is responsive to safety and performance issues in the automotive industry making it a reasonable contender. The on demand ABS Control Module not only avails maximum control, braking and minimizes stopping distances but also provides better adaptability for all surfaces thus reflecting the intelligent design of the car. The Ford E-250 ABS Control Module is designed to be compatible with several models of E-250 and for that reason the part remains very popular with drivers as they can be assured of safe and efficient driving. About the Ford E-250 ABS Control Module in summary, one can only applaud Ford's efforts to put forth its premier foot in the field of vehicle safety concerns and achieving optimum results.

Ford E-250 ABS Control Module Parts and Q&A

Modulator Valve
6C2Z-2C286-BA
Q: How to Bleed the Brake System After Installing a New ABS Control Module on Ford E-250?
A:
Start brake bleeding procedures after new four-wheel anti-lock brake system (4WABS) hydraulic control unit (HCU) installation or when opening the HCU lines by first cleaning Brake Master Cylinder filler cap dirt before filling the reservoir with clean DOT 3 brake fluid. A waste line made from clear tubing should link with the right-hand (RH) rear bleeder screw with the waste end positioned below clean DOT 3 brake fluid. Apply pressure to the brake pedal as an assistant tightens the RH rear bleeder screw at a point when brake fluid starts to flow. Follow this procedure until the brake fluid runs clear without bubbles then restart the reservoir as required. It is necessary to repeat the bleeding procedure that begins with tightening the LH rear bleeder screw to 15 Nm (11 ft. lbs.) followed by disconnecting the waste line and proceeding through the RH front disc Brake Caliper bleeder screw and finally the LH front disc brake caliper bleeder screw in sequence. The diagnostic tool needs to be connected to the data link connector (DLC) in order to perform the bleeding procedure following the tool instructions that match the original steps.
Control Valve
7C2Z-2C219-CA
Q: How to Service and Repair the ABS Control Module on Ford E-250?
A:
The service and repair process for the Electronic Brake Control Module must start by taking out the Hydraulic Control Unit (HCU). The next step requires the removal of screws which are securing the ABS module. Finish the installation process by following the backward order of the removal steps.