How to service and repair the 9.75-inch ring gear axle shaft assembly on Ford E-250?

Beginning the service and repair of 9.75-inch ring gear axle shaft assembly requires setting the vehicle to neutral position then hoisting it for maintenance. The first step requires removal of the wheel along with the tire before extracting the differential housing cover. Drain the stored lubricant from the unit. Security of the rear disc brake calipers should follow their detachment from the system before removing the rear brake discs. You must begin the procedure by removing the differential pinion shaft yet keeping the lock bolt and extracting the shaft from its position. A proper U-washer removal requires pushing the axle shafts inboard because damaging the rubber O-ring O-rings creates installation problems. Take out the two axle shafts while preserving the wheel bearing oil seal's state of undamaged condition. At installation time apply grease to the lip of the wheel bearing oil seal then install the two axle shafts from the correct side of the U-washers without harming either the oil seal or rubber O-rings. Place the U-washers against the button terminals of each axle shaft and slowly extend the shafts out from the housing. Insert and secure the differential pinion shaft into position by aligning the horizontal hole with the case lock bolt hole while using a new lock bolt to fasten it. To complete the reinstall install brake discs and calipers while you should cover the differential housing and add specified lubricant to the housing before you install the tire and wheel assembly.

OEM Ford E-250 Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Axle Shafts found

View related parts
Ford E-250 Axle Shaft, Rear Driver Side Part Number: YC2Z-4234-AB
$206.00 MSRP: $302.50
You Save: $96.50 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; CV Axle Shaft, Rear Left; Axle Shafts
- Manufacturer Note: LH - use with axle #YC25-YA, ZA, 1C24-RA, SA, 2C24-AA, BA, 3C24-AA, BA, 4C24-AA, AB, 6C24-BA - 2000/
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Axle Shaft, Rear Driver Side Part Number: F8UZ-4234-AB
$330.85 MSRP: $485.83
You Save: $154.98 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Left; Axle Shafts
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2014 Ford E-250 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Axle Shaft, Rear Passenger Side Part Number: YC2Z-4234-AA
$204.04 MSRP: $297.00
You Save: $92.96 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; CV Axle Shaft, Rear Right; Axle Shafts
- Manufacturer Note: RH - use with axle #YC25-YA, ZA #1C24-RA, SA, 2C24-AA, BA, 3C24-AA, BA, 4C24-AA, AB, 6C24-BA - 2000/
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford E-250 Axle Shaft, Rear Driver Side Part Number: F5UZ-4234-B
$334.60 MSRP: $491.33
You Save: $156.73 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Rear Axle Outer Stub; Drive Axle Shaft, Rear Left; Axle Shafts
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2014 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Axle Shaft, Rear Passenger Side Part Number: 9C2Z-4234-A
$489.19 MSRP: $718.33
You Save: $229.14 (32%)
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Right; Axle Shafts
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2014 Ford E-250 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Axle Shaft, Rear Passenger Side Part Number: F8UZ-4234-AA
$329.60 MSRP: $484.00
You Save: $154.40 (32%)
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Right; Axle Shafts
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2014 Ford E-250 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Axle Shaft, Rear Driver Side Part Number: 9C2Z-4234-B
$489.19 MSRP: $718.33
You Save: $229.14 (32%)
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Left; Axle Shafts
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2014 Ford E-250 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-250 Axle Shaft, Rear Passenger Side Part Number: F5UZ-4234-A
$332.10 MSRP: $487.67
You Save: $155.57 (32%)
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Right; Axle Shafts
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2014 Ford E-250 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG

Ford E-250 Axle Shaft

OEM Axle Shaft boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Axle Shaft with long life and a perfect fit. Come to our website and find genuine Ford E-250 parts. We keep a wide inventory of OEM E-250 parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Ford E-250 Axle Shaft is among the most respected utilitarian items that work effectively in transferring the power from the differential to the drive wheels. This functionality enables the wheels to turn separately, and this helps in improving the tractions that are required in cornering which makes the Ford E-250 safe and efficient. Suitable to use on any model of E-250, the Axle Shaft is built to perform in work and everyday settings to guarantee that the driver has a reliable car at any given time. In the Ford E-250 Axle Shaft, two basic axle kinds are used: solid axles and halfshafts, with every type and model developed for a specific use within the entire line of E-250 vehicles. It offers strong support for weight and torque of a vehicle through the solid axle, then the half shaft of solid axle that offers better handling especially in independant suspension. It is essential to perform a routine maintenance service on the Ford E-250 Axle Shaft because wear and matters like noise and vibration may be experienced, hence improving the drive. More specifically, the Ford E-250 Axle Shaft has received new technological solutions that affect the products' durability and performance on the automotive market. The Ford E-250 Axle Shaft offers strength, efficiency and safety hence making it a product many people consider when in need of a solution that will enhance their automobiles powertrain.

Ford E-250 Axle Shaft Parts and Q&A

Axle Shaft, Rear Driver Side
YC2Z-4234-AB
Q: How to service and repair the 9.75-inch ring gear axle shaft assembly on Ford E-250?
A:
Beginning the service and repair of 9.75-inch ring gear axle shaft assembly requires setting the vehicle to neutral position then hoisting it for maintenance. The first step requires removal of the wheel along with the tire before extracting the differential housing cover. Drain the stored lubricant from the unit. Security of the rear disc Brake Calipers should follow their detachment from the system before removing the rear Brake Discs. You must begin the procedure by removing the differential pinion shaft yet keeping the lock bolt and extracting the shaft from its position. A proper U-washer removal requires pushing the axle shafts inboard because damaging the rubber O-ring O-rings creates installation problems. Take out the two axle shafts while preserving the wheel bearing oil seal's state of undamaged condition. At installation time apply grease to the lip of the wheel bearing oil seal then install the two axle shafts from the correct side of the U-washers without harming either the oil seal or rubber O-rings. Place the U-washers against the button terminals of each axle shaft and slowly extend the shafts out from the housing. Insert and secure the differential pinion shaft into position by aligning the horizontal hole with the case lock bolt hole while using a new lock bolt to fasten it. To complete the reinstall install brake discs and calipers while you should cover the differential housing and add specified lubricant to the housing before you install the tire and wheel assembly.