How to service the right-hand temperature blend door actuator on Ford Taurus?

The glove compartment servicing operation requires you to first disassemble the damper component before you lower the compartment. You need to reach the actuator inside the glove compartment while disconnecting the jumper harness electrical connection of the temperature blend door actuator. Begin by unwiring the instrument panel wire harness at the heater core and evaporator core housing support using its pin-type retainer then proceed to remove the pin-type retainer for the in-vehicle temperature sensor aspirator hose on the instrument panel support. First detach the two screws which keep the right-hand temperature blend door actuator in place before moving the actuator to disconnect the electrical connector. The new actuator installation requires readers to perform the opposite sequence of removel steps along with returning the original equipment.

How to service the LH temperature blend door actuator on Ford Taurus?

Guests must reach the LH temperature blend door actuator by accessing it from the LH side of the instrument panel below. Start the procedure by unscrewing the two fasteners that attach the left hand temperature blend door actuator. Step two is to disconnect the electrical connector which attaches to the actuator. The actuator must be detached following the disconnection of the electrical connector. The installation process for the new actuator begins by performing the steps in reverse order from removal.

OEM Ford Taurus Blend Door Actuator

Air Blend Door Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Blend Door Actuators found

View related parts
Ford Taurus Door Actuator, Driver Side Part Number: AA5Z-19E616-C
$28.03 MSRP: $44.51
You Save: $16.48 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Motor Assembly; HVAC Air Inlet Door Actuator, Front Lower; Front; Air Adjustment Control Motor; Right; Left; Vacuum Motor; Adjust Motor; Motor
- Position: Driver Side
- Replaces: 8G1Z-19E616-B, 8G1Z-19E616-C, AA5Z-19E616-B, YH-1778
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Motor Assembly Part Number: XF1Z-19E616-CA
Product Specifications
- Other Name: HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Blower Motor; Actuator
- Manufacturer Note: w/manual A/C
- Replaces: F7DZ-19E616-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2007 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Motor Assembly Part Number: F7DZ-19E616-BA
Product Specifications
- Other Name: HVAC Air Inlet Door Actuator; HVAC Blend Door Actuator; HVAC Heater Blend Door Actuator; Blower Motor; Motor; Actuator
- Manufacturer Note: with EATC
- Replaces: F6DZ-19E616-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2007 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Door Actuator, Front Upper Part Number: AA5Z-19E616-A
$19.29 MSRP: $29.85
You Save: $10.56 (36%)
Product Specifications
- Other Name: Motor Assembly; HVAC Air Inlet Door Actuator, Front Upper; Defrost Mode Door Actuator; Heater Blend Door Actuator; Vacuum Motor; Adjust Motor; Motor
- Position: Front Upper
- Replaces: 7L1Z-19E616-G, 9L3Z-19E616-A, 5F2Z-19E616-AA, 4F2Z-19E616-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS

Ford Taurus Blend Door Actuator

OEM Blend Door Actuator boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Blend Door Actuator with long life and a perfect fit. Come to our website and find genuine Ford Taurus parts. We keep a wide inventory of OEM Taurus parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Taurus Blend Door Actuator Parts and Q&A

Door Actuator, Front Upper
AA5Z-19E616-A
Q: How to service the right-hand temperature blend door actuator on Ford Taurus?
A:
The glove compartment servicing operation requires you to first disassemble the damper component before you lower the compartment. You need to reach the actuator inside the glove compartment while disconnecting the jumper harness electrical connection of the temperature blend door actuator. Begin by unwiring the instrument panel wire harness at the Heater Core and evaporator core housing support using its pin-type retainer then proceed to remove the pin-type retainer for the in-vehicle temperature sensor aspirator hose on the instrument panel support. First detach the two screws which keep the right-hand temperature blend door actuator in place before moving the actuator to disconnect the electrical connector. The new actuator installation requires readers to perform the opposite sequence of removel steps along with returning the original equipment.
Door Actuator, Driver Side
AA5Z-19E616-C
Q: How to service the LH temperature blend door actuator on Ford Taurus?
A:
Guests must reach the LH temperature blend door actuator by accessing it from the LH side of the instrument panel below. Start the procedure by unscrewing the two fasteners that attach the left hand temperature blend door actuator. Step two is to disconnect the electrical connector which attaches to the actuator. The actuator must be detached following the disconnection of the electrical connector. The installation process for the new actuator begins by performing the steps in reverse order from removal.