How to Service the Crankshaft Position Sensor on Lincoln Navigator?

The first step to service the crankshaft position (CKP) sensor requires you to disconnect the battery ground cable. The service starts by moving the accessory drive belt from the A/C compressor pulley before lifting and supporting the vehicle. You must disconnect the electrical connector of the A/C compressor field coil before disconnecting the CKP sensor electrical connector and detaching the wiring harness. Access to the CKP sensor becomes possible by sliding the compressor down one inch after the A/C compressor bolts receive only enough release to create this opening. Unbolt the sensor from its position while you remove the CKP sensor from the system. The reverse steps from removal must be followed for product installation.

How to properly service the Crankshaft Position Sensor on a Lincoln Continental?

The first step requires that technicians height and sustain a vehicle and disable air suspension electrical power at the right-hand kick panel area air suspension switch to avoid air spring sudden pressure or vacuum variations which could move the vehicle before service completion. Start by detaching the engine control sensor wires from the Crankshaft Position Sensor (CKP sensor). Proceed with removing the bolt that fastens the CKP sensor to remove the sensor from its position. To install the component follow the steps in reverse order of removal.

How to Service the Crankshaft Position Sensor on Lincoln Town Car?

The service of Crankshaft Position (CKP) Sensor should begin by raising the vehicle on a hoist and placing it in NEUTRAL position. The accessory drive belt needs to be removed from the A/C compressor pulley while the technician rotates the tensioner according to procedure before disconnecting the A/C compressor field coil electrical connector and the CKP sensor electrical connector. First cut off the two wiring harness clips by unwinding the nut from the connection. The three A/C compressor stud bolts need to be loosened gently to allow the compressor descent one inch for accessing the CKP sensor installation area. When you remove the retaining bolt then you can extract the CKP sensor from its place. Follow these steps for installation by rolling up the A/C compressor one inch but do not remove the bolts and perform bolt tightening to 9 Nm (80 lb-in).

OEM Lincoln Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Crankshaft Position Sensors found

View related parts
Lincoln Crankshaft Position Sensor
Part Number: BL3Z-6C315-B
$20.84 MSRP: $33.09
You Save: $12.25 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Replaces: BL3Z-6C315-A, DY-1177
Fits the following Lincoln Models:
- MKT | 2010-2019 | Base, EcoBoost, Livery, Premiere, Reserve | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
- Navigator | 2015-2024 | Base, Black Label, L, L Base, L Black Label, L Livery, L Reserve, L Select, Premiere, Reserve, Select | 6 Cyl 3.5 L GAS
View related parts
Lincoln Crankshaft Position Sensor
Part Number: AA5Z-6C315-A
$46.83 MSRP: $74.36
You Save: $27.53 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Manufacturer Note: Includes Attaching Bolt
- Replaces: AT4Z-6C315-A, 7T4Z-6C315-B
Fits the following Lincoln Models:
- Continental | 2017-2020 | Base, Livery, Premiere, Select | 6 Cyl 3.7 L GAS
- MKS | 2009-2016 | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
- MKT | 2010-2019 | Base, EcoBoost, Livery, Premiere | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
- MKX | 2007-2018 | Base, Black Label, Premiere, Reserve, Select | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
- MKZ | 2007-2016 | Base, Black Label | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View More
View related parts
Lincoln Crankshaft Position Sensor
Part Number: 5L8Z-6C315-AA
$25.22 MSRP: $40.05
You Save: $14.83 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Manufacturer Note: Also Used As Camshaft Position Sensor
Fits the following Lincoln Models:
- Zephyr | 2006 | Base | 6 Cyl 3.0 L GAS
View related parts
Lincoln Crankshaft Position Sensor
Part Number: 1W7Z-6C315-AB
$41.11 MSRP: $65.27
You Save: $24.16 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Position Sensor; Sensor - Crankshaft Position - Cps
- Manufacturer Note: Sensor asy. (Crankshaft position) #1W7E 6C315-AA
- Replaces: 1W7Z-6C315-AA
Fits the following Lincoln Models:
- Aviator | 2003-2005 | Base | 8 Cyl 4.6 L GAS
- Blackwood | 2002 | Base | 8 Cyl 5.4 L GAS
- Mark LT | 2006-2008 | Base | 8 Cyl 5.4 L GAS
- Mark VIII | 1993-1998 | Anniversary, Base, LSC | 8 Cyl 4.6 L GAS
- Navigator | 1998-2017 | Base, L, L Luxury, L Reserve, L Select, L Ultimate, Luxury, Reserve, Select, Ultimate | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
- Town Car | 1991-2011 | Anniversary, Base, Cartier, Cartier L, Cypress, Designer Series, Executive, Executive L, Executive Protection Series, Jack Nicklaus, Protection Series, Signature, Signature L, Signature Limited, Touring Edition, Tournament Edition, Ultimate, Ultimate L | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View More
View related parts
Lincoln Crankshaft Position Sensor
Part Number: 6M8Z-6C315-AA
$69.99 MSRP: $115.16
You Save: $45.17 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Camshaft Position Sensor; Sensor - Crankshaft Position - Cps
Fits the following Lincoln Models:
- MKC | 2015-2019 | Base, Black Label, Premiere, Reserve, Select | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
- MKT | 2013-2016 | Base
- MKZ | 2013-2020 | Black Label Hybrid, Hybrid, Premiere Hybrid, Reserve Hybrid, Reserve I Hybrid, Reserve II Hybrid, Select Hybrid | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV)
View More
View related parts
Lincoln Crankshaft Position Sensor
Part Number: EOAZ6C315A
$29.09 MSRP: $40.24
You Save: $11.15 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Crankshaft Position; Sensor - Crankshaft Position - Cps
Fits the following Lincoln Models:
- Continental | 1984 | Base, Givenchy, Valentino | 6 Cyl 2.4 L DIESEL, 8 Cyl 5.0 L GAS
- Mark VII | 1984 | Base, Bill Blass, LSC, Versace | 6 Cyl 2.4 L DIESEL, 8 Cyl 5.0 L GAS
- Town Car | 1984 | Base, Cartier, Signature | 8 Cyl 5.0 L GAS
View More
View related parts
Lincoln Crankshaft Position Sensor
Part Number: JX6Z-6C315-B
$36.36 MSRP: $56.75
You Save: $20.39 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor
- Replaces: AS7Z-6C315-A, DY-1461, DY-1204, JX6Z-6C315-A
Fits the following Lincoln Models:
- Corsair | 2020-2023 | Base, Grand Touring, Reserve | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
- MKC | 2017-2019 | Base, Black Label, Premiere, Reserve, Select | 4 Cyl 2.0 L GAS
- MKZ | 2013-2020 | Base, Black Label, Premiere, Reserve, Reserve I, Reserve II, Select | 4 Cyl 2.0 L GAS
- Nautilus | 2019-2023 | Base, Black Label, Reserve, Select | 4 Cyl 2.0 L GAS
View More
View related parts
Lincoln Crankshaft Position Sensor
Part Number: FT4Z-6C315-C
$55.98 MSRP: $93.80
You Save: $37.82 (41%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor
- Replaces: FT4Z-6C315-A, DY-1288
Fits the following Lincoln Models:
- Aviator | 2020-2023 | Base, Black Label, Black Label Grand Touring, Grand Touring, Livery, Reserve | 6 Cyl 3.0 L GAS, 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV)
- Continental | 2017-2020 | 80th Anniversary Coach Door Edition, Black Label, Coach Door Edition, Reserve, Select | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
- MKX | 2016-2018 | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS
- MKZ | 2017-2020 | Black Label, Reserve, Reserve II, Select | 6 Cyl 3.0 L GAS
- Nautilus | 2019-2023 | Black Label, Reserve, Select | 6 Cyl 2.7 L GAS
View More
View related parts
Lincoln Crankshaft Position Sensor
Part Number: 1F1Z-6C315-AB
$19.81 MSRP: $31.45
You Save: $11.64 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Replaces: 1F1Z-6C315-AA
Fits the following Lincoln Models:
- LS | 2000-2005 | Appearance, Base, LSE, Luxury, Premium | 6 Cyl 3.0 L GAS
View related parts
Lincoln Crankshaft Position Sensor
Part Number: 5M6Z-6C315-A
$98.17 MSRP: $161.53
You Save: $63.36 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Replaces: 3M6Z-6C315-AA
Fits the following Lincoln Models:
- MKZ | 2011-2012 | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Lincoln Crankshaft Position Sensor
Part Number: XW4Z-6C315-BB
$47.51 MSRP: $64.65
You Save: $17.14 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
Fits the following Lincoln Models:
- LS | 2000-2006 | Appearance, Base, LSE, Luxury, Premium, Sport, Ultimate | 6 Cyl 3.0 L GAS, 8 Cyl 3.9 L GAS
View related parts
Lincoln Crankshaft Position Sensor
Part Number: 1F3Z-6C315-AA
Product Specifications
- Other Name: Sensor - Crankshaft; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Manufacturer Note: (HDR)sensor RH side of 6019
Fits the following Lincoln Models:
- Continental | 1995-2002 | Anniversary, Base, Diamond Anniversary, Signature, Spinnaker Edition | 8 Cyl 4.6 L GAS

Lincoln Crankshaft Position Sensor Parts Questions & Experts Answers

Crankshaft Position Sensor
1W7Z-6C315-AB
Q: How to Service the Crankshaft Position Sensor on Lincoln Navigator?
A: The first step to service the crankshaft position (CKP) sensor requires you to disconnect the battery ground cable. The service starts by moving the accessory drive belt from the A/C compressor pulley before lifting and supporting the vehicle. You must disconnect the electrical connector of the A/C compressor field coil before disconnecting the CKP sensor electrical connector and detaching the wiring harness. Access to the CKP sensor becomes possible by sliding the compressor down one inch after the A/C compressor bolts receive only enough release to create this opening. Unbolt the sensor from its position while you remove the CKP sensor from the system. The reverse steps from removal must be followed for product installation.
Crankshaft Position Sensor
1F3Z-6C315-AA
Q: How to properly service the Crankshaft Position Sensor on a Lincoln Continental?
A: The first step requires that technicians height and sustain a vehicle and disable air suspension electrical power at the right-hand kick panel area air suspension switch to avoid air spring sudden pressure or vacuum variations which could move the vehicle before service completion. Start by detaching the engine control sensor wires from the Crankshaft Position Sensor (CKP sensor). Proceed with removing the bolt that fastens the CKP sensor to remove the sensor from its position. To install the component follow the steps in reverse order of removal.
Crankshaft Position Sensor
1W7Z-6C315-AB
Q: How to Service the Crankshaft Position Sensor on Lincoln Town Car?
A: The service of Crankshaft Position (CKP) Sensor should begin by raising the vehicle on a hoist and placing it in NEUTRAL position. The accessory drive belt needs to be removed from the A/C compressor pulley while the technician rotates the tensioner according to procedure before disconnecting the A/C compressor field coil electrical connector and the CKP sensor electrical connector. First cut off the two wiring harness clips by unwinding the nut from the connection. The three A/C compressor stud bolts need to be loosened gently to allow the compressor descent one inch for accessing the CKP sensor installation area. When you remove the retaining bolt then you can extract the CKP sensor from its place. Follow these steps for installation by rolling up the A/C compressor one inch but do not remove the bolts and perform bolt tightening to 9 Nm (80 lb-in).