Ford 7R3Z-17664-A
Washer Pump

Service starts by hood support then battery removal along with the battery tray using bolt extraction. Place a collecting container beneath the windshield washer hose when you disconnect it to collect the fluid inside the reservoir. First unmount the washer pump and reservoir by taking out the nut and bolt then removing the filler hose and electrical connector. The first step is to separate the wiring harness locator from the washer pump and reservoir and afterward disconnect the windshield washer hose before completing the removal with washer pump and reservoir. Take the washer pump out of the reservoir after finishing the removal process. Perform the installation procedure by following the exact opposite steps of removal. Refilling the windshield washer reservoir needs to be done before both electrical connections and pump operation.

The servicing process starts with taking off both the engine air cleaner and windshield wiper reservoir fasteners that comprise two screws and two nuts. Complete the service of the windshield washer reservoir pump by disconnecting the electrical connector. The windshield washer solution includes methanol which functions as a poisonous substance therefore consumers must read all safety warnings on the solution container. Familiarize and disconnect the windshield washer hose from the pump while using a plug to seal the pump outlet. It is essential to disconnect and plug the hose connecting the engine coolant overflow reservoir with the overflow tank. Take all necessary precautions to prevent any damage to the rubber grommet when disassembling it. The installation of new components requires you to perform the removal reversal steps.

Caretaking or repairing the windshield washer pump and reservoir requires first removing the battery tray and setting the windshield washer fluid reservoir to the side. You should first disconnect the electrical connector while removing the bolts which keep the reservoir in place. The hazardous properties of windshield washer solution require implementing all safety warnings and precautions from its container label. Put the windshield washer fluid into a container following windshield washer hose disconnect and then disconnect and collect the rear window washer fluid as necessary. Proceed to take out the windshield washer pump after getting rid of the windshield washer fluid reservoir. Avoid electrical connections before reservoir filling because it is essential to wait until the reservoir is filled before operating the windshield washer pump. After finishing the installation you should follow the steps in reverse order of removal.

Service and repair of the windshield washer pump and reservoir starts with securely following all warnings about the poisonous properties of methanol in windshield washer solution according to the label on the container. Before connecting any electrical components to service the windshield washer pump constantly check the reservoir has proper fluid level. Reducing power to the vehicle at first followed by wheel removal allows safe placement of the right front splash shield. The first step of the installation is to remove screws to separate the right-hand corner lamp following the diagram order. Installation requires reversing the removal steps starting with filling the windshield washer reservoir through the inner frame support before attaching its hoses to the reservoir.

Vehicle servicing of the windshield washer pump requires placing it on a hoist with NEUTRAL gear selection. Disconnect the windshield washer pump hose for drainage of solvent before disconnecting its electrical connector. You should extract the windshield washer pump from its place of attachment. The two bolts must be removed from the fluid reservoir before you can detach it by removing the nut. During reinstallation you must tighten all bolts and the nut to 6 Nm (53 lb-in) torque value. Operating the windshield washer pump should be avoided before correctly filling the reservoir. After performing the installation you should execute the opposite steps used during removal. Treatment of windshield washer solution must be cautious because it contains poisonous and flammable methanol.

The repair of windshield washer pump and reservoir requires operators to first disconnect battery cables followed by the removal of the battery heat shield. Move on by detaching the jack handle from the windshield washer reservoir as well as the electrical connector from the windshield washer pump. The service procedure begins with screw removal from the windshield washer reservoir and fluid collection from the washer hose before disconnecting the reservoir. After detaching the hose, remove both the windshield washer reservoir and the washer pump only if needed. Installation procedures include preventing electrical connections until the washer reservoir has fluid then waiting to operate the pump until fluid reaches its maximum level. Following the battery reconnection you should expect the vehicle to learn its adaptive strategy again while showing certain unusual drive symptoms until reaching 16 km (10 miles) driving distance. The installation process ends by reversing the removal steps while filling the windshield washer reservoir with ultra-clear windshield washer concentrate C9AZ-19550-AC or BC or any material that satisfies Ford specification ESR-M17P5-A.

The windshield washer pump servicing requires you to empty the reservoir first to stop spills followed by hose disconnect from the pump. The second step involves disconnecting the coolant overflow hose from the engine coolant overflow reservoir while plugging the outlet port. Locate the electrical connector on the windshield washer reservoir pump before removing it while placing the air filter housing to the side. Clear the windshield washer reservoir by removing both screws and two nuts then extract the reservoir with care. Be cautious when pulling out the washer pump from the reservoir because damage can occur to the rubber grommet. The windshield washer reservoir installation as well as the washer pump service must be done independently according to the removal reversal procedure.

The process of servicing or repairing the windshield washer pump starts with wheel and tire removal of the left front position then moving forward to expose the left front inner splash shield. Disconnect both electrical connections and washer hose located on the washer pump before extracting the pump. Before taking off the windshield washer reservoir ensure draining its contents because the washer solution possesses methanol making it poisonous. Observe all warnings and cautions shown on solution bottle labels. To install these components follow the opposite installation steps while keeping in mind to avoid operating the windshield washer pump until the reservoir has sufficient fluid.

Start the windshield washer pump and reservoir service by unthreading the right front wheel assembly with tire then remove the splash shield pin-type retainer and its three retaining screws. Before replacement of the windshield washer fluid you must place it in a designated container when disconnecting from the washer hose. You need to start by removing the windshield washer reservoir together with the pump supply line and then disconnect the electrical connector from the windshield washer pump. The windshield washer reservoir needs three bolts removed before reinstallation where you should tighten each bolt to 6 Nm (53 lb-in). You should finish the installation phases by performing the reverse steps of removal for the windshield washer pump.

Service of the windshield washer pump begins with eliminating the right-side front wheel. To detach the right-hand front inner fender well you have to remove its four screws along with the pin-type retainer. After disconnecting the washer hose and electrical connector from the washer pump users need to be cautious due to the poisonous nature of methanol in the windshield solution as indicated by safety labels on the solution container. The windshield washer reservoir becomes empty whenever the washer hose disconnects from the system. A small flat blade screwdriver should be used to remove the washer pump assembly from the reservoir cavity. Follow the same process backward to reinstall the windshield wiper pump.

The first step to service the windshield washer pump requires users to disconnect the battery ground cable. Raised and supported vehicle before you can take out the pushpins and screws to remove the right-hand front splash shield. Unfasten the washer hose from the washer pump after taking off the splash shield. Start the repair by detaching both the electrical connector and then pulling out the pump from the vehicle. The windshield washer fluid contains poisonous methanol thus you must observe all precautions described on the solution container label. The procedure to avoid spilling starts with draining the windshield washer fluid from its container. To accomplish installation mirror the sequence used for removal. After battery connection and disconnection customers must understand that vehicle behavior will show unusual driving characteristics because it learns its adaptive strategy while needing a minimum 16 km (10 mi) driving distance.

Before servicing the windshield washer pump users must disconnect the hose from the pump then drain the washer reservoir to stop fluid leaks. Discharge the coolant overflow hose from the engine coolant overflow reservoir before plugging its outlet port. First disconnect the electrical connection from the windshield washer reservoir pump before setting aside the air filter housing unit. Detach the windshield washer reservoir by removing its two screws and two nuts before extracting the washer pump from the reservoir without damaging the rubber grommet. Proceed with installation by following the opposite steps of removal while understanding that the washer reservoir and pump service separately.

The first step to work on the windshield washer pump requires disconnecting the battery ground cable. The service begins when the vehicle is properly raised and supported and then proceeds to extract the right-hand front splash shield by unscrewing and pulling out its pushpins. Disconnection of the washer hose from the washer pump requires preliminary fluid drainage to avoid spillage since the solution carries poisonous methanol. Disconnect both the electrical connector and remove the washer pump. Installation should be done by performing the opposite steps of removal. The vehicle will need continued driving for at least 16 km (10 mi) after reconnecting the battery because it relearns its adaptive strategy following this procedure.

The windscreen washer pump repair starts by unbolting upper reservoir elements followed by right-hand tire removal with the wheel and subsequent splash shield detachment. A proper start involves removing the screws from the right-hand cornering lamp for positioning it aside. Shift the washer reservoir to one side after unbolting its lower fastener and disconnecting the level sensor electricity wire. The washer reservoir should be placed aside before disconnecting both electrical connectors and washer hoses from the washer pumps and completing the removal of the washer reservoir. Windshield washer solution contains poisonous methanol thus all cautions and warnings on the washer solution container must be observed. A proper prevention of washer fluid spills requires reservoir fluid draining before uninstalling the reservoir unit. The new components need installation by performing the removal procedure in reverse order.

The service and repair procedures of the windshield washer pump and reservoir begin with following all safety cautions about the poisonous methanol found in windshield washer solutions. Begin by emptying the windshield washer fluid from the reservoir to avoid liquid spillages. Disconnect the electrical connector from the windshield washer pump followed by removing the washer fluid reservoir hose. First loosen then remove the three bolts securing the washer fluid reservoir while tightening them back to 7 Nm (62 lb-in) after installation. When removing the washer fluid reservoir maintain constant attention to the rubber grommet to avoid damage to it while taking out the windshield washer pump. The installation process can be finished by reversing the step of removal.

Firstly service and repair the windshield washer pump following the components removal sequence displayed in the illustration along with the table references. Perform the reverse order of removal steps to install the components. The removal of the engine control sensor wire assembly requires complete jack handle removal because hidden access is necessary.

The service process for windshield washer pump and reservoir begins by disconnecting the battery followed by right front wheel removal. You should first shift the right front splash shield out of the way before extracting the screws which maintain the right front corner lamp. The two bolts need removal for moving the degas bottle to a new location. Disconnect electrical connectors from the windshield washer pump while being aware that the washer solution consists of methanol which is toxic so read all label cautions on the solution container. Vacate suitable storage for the washer reservoir liquid by disconnecting its hoses then draining the container. First disconnect the windshield washer reservoir bolts before you remove the reservoir from its position. The technician must avoid both electrical connections and operating the washer pump until the reservoir reaches its maximum fill point. Plug the windshield washer hoses into the reservoir first before installing the part and follow the removal steps in reverse to finish the installation process.

The first step for servicing or repairing the windshield washer pump and reservoir requires you to remove the air cleaner assembly to position the washer elements aside. The assembly should be bolted out carefully. All cautions and warnings on windshield washer solution containers exist because the product contains methanol which poses a poisoning risk to users. Therefore proper safety measures must be followed to avoid personal injury. You should obtain windshield washer fluid inside a container by disconnecting the hose from the windshield washer system. Disconnect the electrical connectors followed by detaching the washer hose before you remove the washer pump together with its reservoir. Remove the washer pump as the final stage of installation. Cautions arise from avoiding the use of the windshield washer pump until the windshield reservoir has reached its full capacity. Execute the installation by reversing all removal steps.

The process for servicing or correcting the windshield washer pump starts by taking away the air cleaner assembly before setting the washer pump together with the reservoir to one side. Drop the first step by removing bolts from the washer pump and reservoir. Proceed to disconnect the electrical connectors and the washer hose. After the hose disconnection it is vital to place the windshield washer fluid into a suitable container because the solution has toxic methanol ingredients therefore follow all safety instructions from the washer solution label to prevent injuries. To properly reinstall the washer pump start by reversing the removal steps while avoiding operation of the windscreen wiper system until you add fluid to the tank.

The procedure to service windshield washer pump and reservoir starts by removing the air cleaner assembly followed by washer pump and reservoir bolt removal procedure. Personal injury prevention needs all safety warnings and cautions on windshield washer solution containers to be followed because the solution contains toxic methanol substances. Washers fluid for the windshield needs to be collected in a container once the windshield hose is disconnected. The washing pump and reservoir removal process starts with disconnecting electrical connectors and washer hose before you take them out. Follow the installation steps by holding off from pumping the windshield washer before adding fluid to the reservoir and perform the removal steps in reverse order during installation.

The windshield washer pump servicing starts by removing the right-hand front wheel followed by removing four screws with a pin-type retainer to separate the right-hand front inner fender well. Proper caution must be used when working with windshield washer solution because it contains poisonous methanol and all solution container warnings should be followed. Unplugging the washer hose leads to total depletion of fluid from the windshield washer reservoir. You should first decompress the washer hose and eliminate the electrical link from the washer pump. A flat blade screwdriver should be used to pry the pump out of its position in the reservoir cavity during washer pump assembly removal. The procedure to install the component follows the opposite sequence of the removal process.

The first step to repair the windshield washer pump and reservoir requires the battery disconnection. Begin the service by first unscrewing and placing aside the bolt which attaches the windshield washer reservoir. Before continuing disconnect the electrical pump connector but take caution because windshield washer solution includes poisonous methanol thus following all warning labels prevents personal harm. After removing the windshield washer hose for disconnection the level sensor you should put the washer fluid into a storage container. Take off the windshield washer reservoir followed by the windshield washer pump. First priority is to prevent electrical connections before filling the windshield washer reservoir while waiting for the pump start until the reservoir reaches full capacity. The reverse steps from removal will finish the installation process.

You need to start washer pump and washer fluid level sensor removal before performing repair or service operations on the windshield washer pump and reservoir. Any work with windshield washer solution requires observing safety warnings and precautions on the container label as this product contains poisonous methanol substances. Deployment of the windshield washer reservoir requires a preceding drainage step to prevent fluid leakage. The upper radiator hose can be removed if you need better view of the work area. You must disconnect the A/C line bracket together with washer pump hose(s), before removing the A/C line retainer, windshield washer hose and the rear window washer hose if present. Three windshield washer reservoir bolts need to be removed yet should be tightened to 5 Nm (44 lb-in) when reinstalling them. Harmful to health is the methanol content in the washer solution so caution is required before pumping windshield washer liquid into the reservoir. Finishing the installation requires following the removal reversal steps and filling the windshield washer reservoir.

Service of the windshield washer pump and reservoir begins with disconnecting the battery cable followed by removing the bolt which allows relocating the windshield washer reservoir. One must disconnect the windshield washer pump electrical connector while understanding that windshield washer solution holds poisonous methanol which requires following all safety markings and warnings on solution containers to prevent personal injury. Separate the windshield washer fluid level sensor then store leaked fluid in a suitable container once you disconnect the windshield washer hose. Drain the windshield washer reservoir before taking out the windshield washer pump. The installation process requires waiting for the pump operation or electrical connections until after the windshield washer reservoir is filled and the stopping order should be followed for installation completion.

Reverse the removal procedure, ensuring to lubricate the washer pump seal with a soapy solution before assembly.

Be aware that the windshield washer solution contains methanol, which is poisonous and flammable; observe all cautions and warnings on the label of the washer solution container to avoid personal injury.

Reverse the removal procedure to complete the process.

Follow the specified order for removing the components as indicated in the accompanying illustration and table.

Reverse the removal procedure.

The nut should be tightened to 4 Nm (35 lb-in) during installation.

Both should be tightened to 4 Nm (35 lb-in).

Reverse the removal procedure, ensuring to lubricate the washer pump seal with a soapy solution before assembly.

Reinstall it by reversing the removal steps.

Reverse the removal procedure.

Carefully remove the windshield washer pump, taking care not to damage the rubber grommet during disassembly.

The vehicle may exhibit abnormal drive symptoms as it relearns its adaptive strategy.

Disconnect the rear window washer hose as well.

Ensure not to damage the rubber grommet and make sure the reservoir is filled before operating the pump to prevent premature failure.

Be aware that some abnormal drive symptoms may occur as the vehicle relearns its adaptive strategy, which may require driving 16 km (10 miles) or more.

Reverse the removal procedure, taking care not to make the electrical connection before filling the windshield washer reservoir.

It is crucial not to make any electrical connections or operate the windshield washer pump before filling the windshield washer reservoir.

Press an additional cap onto the rear vent tube of the reservoir.

Always observe all cautions and warnings indicated on the label of the washer solution container, as windshield washer fluid contains methanol, which is poisonous.

Disconnect the electrical connector from the pump.

Be cautious of the methanol in the washer solution.

Remove the rear window washer reservoir.

The electrical connector and the wiring harness retainer.

Disconnect the windshield washer pump hose and drain the windshield washer solvent, then disconnect the electrical connector from the pump.

Disconnect the electrical connector from the pump.

Disconnect the windshield washer hose from the pump.

Take off the right-hand front wheel and tire, followed by the right-hand front splash shield.

Position the right-hand cornering lamp aside by removing its screws.

Pull the rear window washer pump straight out from the reservoir.

Reverse the removal procedure.

Disconnect the coolant overflow hose from the engine coolant overflow reservoir and plug the outlet port.

Remove the three bolts securing the washer fluid reservoir.

Remove the lower bolt and disconnect the level sensor electrical connector.

Ensure to collect the windshield washer fluid in a container.

Reverse the removal procedure, ensuring not to make any electrical connections before filling the windshield washer reservoir, and do not operate the pump until the reservoir is filled.

Reverse the removal procedure.

They are serviced independently; remove the two reservoir bolts and two reservoir nuts to take out the windshield washer reservoir.

Remove the windshield washer pump.

Ensure not to make any electrical connections or operate the windshield washer pump before filling the windshield washer reservoir.

Disconnect the windshield washer pump electrical connector and the windshield washer fluid level sensor.

Detach the windshield washer pump from the reservoir.

Begin by disconnecting the battery.

Take care to observe all cautions and warnings regarding the poisonous methanol in the windshield washer solution.

Observe all safety precautions indicated on the solution container, as it contains methanol, which is poisonous.

Next, remove the bolts securing the washer pump and reservoir, then disconnect the electrical connectors and the washer hose.

Disconnect the electrical connector and the washer hose from the washer pump.

Begin by removing the right-hand front wheel.