Continental | 1984-1987 | Base, Givenchy, Valentino | 6 Cyl 2.4 L DIESEL, 8 Cyl 5.0 L GAS
Mark VII | 1984-1992 | Base, Bill Blass, LSC, Versace | 6 Cyl 2.4 L DIESEL, 8 Cyl 5.0 L GAS
Town Car | 1984-1994 | Base, Cartier, Cypress, Executive, Jack Nicklaus, Signature, Signature SE, Touring Edition, Tournament Edition | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
Corsair | 2020-2023 | Base, Reserve | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
MKC | 2015-2019 | Base, Black Label, Reserve, Select | 4 Cyl 2.3 L GAS
MKX | 2016-2018 | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS, 6 Cyl 3.7 L GAS
Nautilus | 2019-2023 | Base, Reserve, Select | 4 Cyl 2.0 L GAS
Navigator | 2007-2024 | Base, Black Label, L, L Base, L Black Label, L Livery, L Luxury, L Reserve, L Select, L Ultimate, Luxury, Premiere, Reserve, Select, Ultimate | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
Other Name: Solenoid Assembly; Vapor Canister Purge Solenoid; Vapor Canister Vent Solenoid; Canister Purge Valve; Vent Control Solenoid; Solenoid
Replaces: CU5Z-9F945-C
Fits the following Lincoln Models:
Aviator | 2020-2023 | Base, Black Label, Black Label Grand Touring, Grand Touring, Livery, Reserve | 6 Cyl 3.0 L GAS, 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV)
Q: How to Address Issues with the Canister Purge Valve on a Lincoln MKZ?
A: The Evaporative Emission Canister Purge Valve demands a safety step to prevent smoking or using lighted tobacco and open flames in the vicinity of fuel-related components due to highly flammable mixture propagation. Personal electronic devices such as cell phones and audio equipment must remain outside the working area when servicing operations take place. It is essential to disconnect the battery ground cable prior to servicing both EVAP components and fuel-related components. The removal process for the EVAP canister purge valve starts with eliminating the lower cowl panel grille on 3.0L and 3.5L vehicles to access the valve. The EVAP canister purge valve electrical connector needs disconnection after taking down the battery ground cable. Remove both vapor jumper tube-to-EVAP canister purge valve quick connect couplings from each other. You can eliminate the EVAP canister purge valve from its bracket by pressing down the tab. Installation of the new valve will proceed by following the uninstallation procedures in reverse order. The Evaporative Emission System Leak Test should be performed right after installation to verify proper system functioning.
Q: How to service and repair the evaporative emission canister purge valve on Lincoln Navigator?
A: The first step for servicing or repairing the evaporative emission canister purge valve requires disconnecting the battery ground cable because this step will prevent electrical sparks that could ignite fuel vapors. The first step should be to remove the EVAP canister purge valve electrical connector before disconnecting both fuel vapor tubes by unclipping their quick connect couplings. The EVAP canister purge valve should be taken from its bracket after disconnection. The installation of the new valve requires following the removal steps in reverse order. After completing installation, test the system for leaks by performing the required drive cycle to confirm the system works correctly.
Q: How to Service and Repair the Canister Purge Valve on Lincoln Town Car?
A: For maintenance and repair of the Canister Purge Valve begin by disconnecting its connector followed by evaporative emission return tube and evaporative emission test port and vacuum hose. The service and repair of the Canister Purge Valve begins by removing its two securing nuts. Install the valve by returning to the removal steps and perform a system leak test. The proper operation of the system needs verification through completion of an evaporative emission repair verification drive cycle.