How to Service the ABS Control Module on Mercury Grand Marquis?

Service of the Electronic Brake Control Module begins by following the procedure to disconnect the battery ground cable. The service begins with disconnecting electrical contacts from the anti-lock brake control module then the control module after that the pump motor. Unfasten the anti-lock brake control module after disconnection of the control module electrical connections. The installation of the components requires performing the opposite steps of removal. Drivers must note that vehicles will demonstrate unusual driving behaviors after battery disconnection until completing relearning of adaptive strategies which might need multiple drives exceeding 16 kilometers (10 miles) for the process to finish.

What are the essential steps and precautions for servicing and repairing the ABS Control Module on Mercury Mariner?

The repair process of the Electronic Brake Control Module requires clean brake fluid from authorized suppliers with manufacturer-standard specifications since using reused fluid can harm system functions and cause injuries to users. When handling brake fluid users need to minimize spillage on paint and plastic surfaces because leakage will lead to surface damage but accidental leaks should have immediate water-based cleaning made to the affected area. ABS modules function as a calibrated unit with the Hydraulic Control Unit so their exchange between vehicles is prohibited. Open the HCU first but focus on the Hydraulic Control Unit removal exclusively for non-hybrid vehicles. Continue with standard procedure to remove HCU followed by jumper tubes fittings and four ABS module screws. Follow the step by removing the jumper tube assembly bracket nut while keeping it tight at 9 Nm (80 lb-in) during installation. Remove the jumper tube assembly from the HCU while keeping the joint fittings loose and preparing to tighten them properly at 15 Nm (133 lb-in). The ABS module require four screws to detach from the vehicle but should be reinstalled using screws tightened to 2 Nm (18 lb-in). Reinstall the ABS module and follow the procedures for module configuration and calibration procedure. The initialization sequence provided by the scan tool must be followed by non-hybrid vehicles yet hybrid vehicles need to perform the Multi-Calibration routine based on the scan tool guidance.

OEM Mercury ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

92 ABS Control Modules found

View related parts
Mercury Modulator Valve Part Number: 9E5Z-2C215-B
$647.75 MSRP: $946.00
You Save: $298.25 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module; ABS Control Module; Actuator
Fits the following Mercury Models:
- Milan | 2010-2011 | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Modulator Valve Part Number: AL8Z-2C215-A
$931.50 MSRP: $1273.85
You Save: $342.35 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module; ABS Control Module
- Manufacturer Note: HCU
Fits the following Mercury Models:
- Mariner | 2010-2011 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Modulator Valve Part Number: AM6Z-2C215-A
$1254.38 MSRP: $1715.38
You Save: $461.00 (27%)
ADD TO CART
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module
- Manufacturer Note: Hydraulic
- Replaces: 9M6Z-2C215-A
Fits the following Mercury Models:
- Mariner | 2009-2011 | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Control Module Part Number: AM6Z-2C219-B
$950.40 MSRP: $1299.69
You Save: $349.29 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module; Controller
- Replaces: 9M6Z-2C219-A, AM6Z-2C219-A
Fits the following Mercury Models:
- Mariner | 2009-2010 | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Control Module Part Number: 9L8Z-2C219-F
$591.53 MSRP: $808.92
You Save: $217.39 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Modulator Valve; ABS Control Module; Controller
- Replaces: 9L8Z-2C219-C, 9L8Z-2C219-D
Fits the following Mercury Models:
- Mariner | 2009-2010 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Modulator Valve Part Number: BE5Z-2C215-A
$648.00 MSRP: $886.15
You Save: $238.15 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module; ABS Control Module; Actuator
- Replaces: AE5Z-2C215-A
Fits the following Mercury Models:
- Milan | 2010-2011 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Control Module Part Number: 9W7Z-2C219-A
$1105.88 MSRP: $1512.31
You Save: $406.43 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
Fits the following Mercury Models:
- Grand Marquis | 2009-2011 | LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Control Module Part Number: BE5Z-2C219-G
$1097.29 MSRP: $1497.69
You Save: $400.40 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaced by: RU2Z-2C219-A
- Replaces: AE5Z-2C219-G, BE5Z-2C219-C, AE5Z-2C219-C, AE5Z-2C219-F
Fits the following Mercury Models:
- Milan | 2010-2011 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Control Module Part Number: 8G1Z-2C219-D
$588.51 MSRP: $814.15
You Save: $225.64 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 8G1Z-2C219-A
Fits the following Mercury Models:
- Sable | 2008-2009 | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Motor & Pump Part Number: 9E5Z-2C215-A
$742.50 MSRP: $1015.38
You Save: $272.88 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module; ABS Pump And Motor Assembly; ABS Control Module; Actuator
Fits the following Mercury Models:
- Milan | 2009 | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Control Module Part Number: XL2Z-2C219-BA
$269.00 MSRP: $364.62
You Save: $95.62 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
Fits the following Mercury Models:
- Mountaineer | 1999-2001 | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Modulator Valve Part Number: 9L8Z-2C346-C
$990.00 MSRP: $1353.85
You Save: $363.85 (27%)
Product Specifications
- Other Name: Module - ABS Control; ABS Control Module; Module
- Manufacturer Note: HCU & ECU
- Replaces: 9L8Z-2C346-A, 9L8Z-2C346-B
Fits the following Mercury Models:
- Mariner | 2009 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Control Module Part Number: BM6Z-2C219-A
$760.50 MSRP: $1040.00
You Save: $279.50 (27%)
Product Specifications
- Other Name: Control; ABS Control Module; Controller
Fits the following Mercury Models:
- Mariner | 2011 | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Control Module Part Number: AL8Z-2C219-A
$343.74 MSRP: $463.08
You Save: $119.34 (26%)
Product Specifications
- Other Name: Control; ABS Control Module; Controller
Fits the following Mercury Models:
- Mariner | 2010 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Control Module Part Number: 9L2Z-2C219-D
$490.32 MSRP: $664.62
You Save: $174.30 (27%)
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Replaces: AL2Z-2C219-C, 9L2Z-2C219-C
Fits the following Mercury Models:
- Mountaineer | 2009-2010 | Base, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Modulator Valve Part Number: 4L2Z-2C215-AA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: HCU
Fits the following Mercury Models:
- Mountaineer | 2004-2005 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Modulator Valve Part Number: 4L2Z-2C215-BA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: HCU
Fits the following Mercury Models:
- Mountaineer | 2004-2005 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Control Module Part Number: 3W1Z-2C219-AA
$885.38 MSRP: $1210.77
You Save: $325.39 (27%)
Product Specifications
- Other Name: Control; ABS Control Module
Fits the following Mercury Models:
- Grand Marquis | 2003-2004 | GS, LS, LSE | 8 Cyl 4.6 L GAS
View related parts
Mercury Control Module Part Number: 9G1Z-2C219-B
$1257.30 MSRP: $1719.38
You Save: $462.08 (27%)
Product Specifications
- Other Name: Control; ABS Control Module; Module
- Replaces: 9G1Z-2C219-A
Fits the following Mercury Models:
- Sable | 2009 | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Modulator Valve Part Number: 8G1Z-2C346-F
$1805.63 MSRP: $2469.23
You Save: $663.60 (27%)
Product Specifications
- Other Name: Module - ABS Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit; Control Assembly
- Manufacturer Note: ECU & HCU
- Replaces: 8G1Z-2C346-C
Fits the following Mercury Models:
- Sable | 2008 | Base, Premier | 6 Cyl 3.5 L GAS

| Page 1 of 5 |Next >

1-20 of 92 Results

Mercury ABS Control Module

If you own Mercury and want to keep it in top shape, choosing OEM ABS Control Module is a smart move. They are precisely engineered and follow strict factory standards. They are made in advanced facilities that use cutting edge technology. Each part goes through thorough testing to confirm strength and safety, so you can trust it. FordPartsDeal.com gives you genuine Mercury ABS Control Module at some of the affordable online prices without cutting quality. Every OEM Mercury part includes the manufacturer's warranty, easy returns, and super-fast delivery. So why wait? Shop now and get your vehicle back to peak condition.

Mercury ABS Control Module ensures wheels do not give way when there is pressure, enabling drivers to have consistent steering on hard stops. In 1939, Mercury unleashed the showrooms with vehicles that offered a more relaxed ride with hard-edged style and accessible prices. Mercury was named after the fleet-footed Roman god that made the badge easy to remember and glided across American roads. Over the decades, the brand combined spacious cabins with muted glass and plush suspension tuning so that commuters would feel free to travel long-distance highways without sensing cost savings. The innovations came one right after the other, starting with better sound insulation to user-friendly dashboards to ensure that the controls were not too complicated for ordinary drivers. The legacy of balanced comfort and value remained bright even in 2011 when production ceased among loyal owners. The ABS Control Module today operates in the entire range of reading wheel speed control signals in hundreds of rapid bursts per second and modulates brake pressure in thousands of rapid bursts per second. When the sensors detect a wheel that is about to lock, the ABS Control Module hydraulic force is reapplied in a way that traction remains alive, but steering is still responsive. Through communication with stability and traction software, the ABS Control Module contracts individual brakes or releases throttle in order to hold the car together on slippery curves and sudden lane alterations. Mercury will combine this ABS Control Module with tough circuitry and closed housing that shake off road spray, heat, and winter salinity. All the Mercury roller with the unit can hammer the pedal feel through the footwell and continue to point precisely where the driver points.

Mercury ABS Control Module Parts and Q&A

Control Module
F8VZ-2C219-BA
Q: How to Service the ABS Control Module on Mercury Grand Marquis?
A:
Service of the Electronic Brake Control Module begins by following the procedure to disconnect the battery ground cable. The service begins with disconnecting electrical contacts from the anti-lock brake control module then the control module after that the pump motor. Unfasten the anti-lock brake control module after disconnection of the control module electrical connections. The installation of the components requires performing the opposite steps of removal. Drivers must note that vehicles will demonstrate unusual driving behaviors after battery disconnection until completing relearning of adaptive strategies which might need multiple drives exceeding 16 kilometers (10 miles) for the process to finish.
Control Module
9L8Z-2C219-F
Q: What are the essential steps and precautions for servicing and repairing the ABS Control Module on Mercury Mariner?
A:
The repair process of the Electronic Brake Control Module requires clean brake fluid from authorized suppliers with manufacturer-standard specifications since using reused fluid can harm system functions and cause injuries to users. When handling brake fluid users need to minimize spillage on paint and plastic surfaces because leakage will lead to surface damage but accidental leaks should have immediate water-based cleaning made to the affected area. ABS modules function as a calibrated unit with the Hydraulic Control Unit so their exchange between vehicles is prohibited. Open the HCU first but focus on the Hydraulic Control Unit removal exclusively for non-hybrid vehicles. Continue with standard procedure to remove HCU followed by jumper tubes fittings and four ABS module screws. Follow the step by removing the jumper tube assembly bracket nut while keeping it tight at 9 Nm (80 lb-in) during installation. Remove the jumper tube assembly from the HCU while keeping the joint fittings loose and preparing to tighten them properly at 15 Nm (133 lb-in). The ABS module require four screws to detach from the vehicle but should be reinstalled using screws tightened to 2 Nm (18 lb-in). Reinstall the ABS module and follow the procedures for module configuration and calibration procedure. The initialization sequence provided by the scan tool must be followed by non-hybrid vehicles yet hybrid vehicles need to perform the Multi-Calibration routine based on the scan tool guidance.